IKEA GULLIVER changing table assembly instructions
How to assemble the IKEA GULLIVER changing table, step by step: 17 animated steps built from the official manual, about 45–60 min for 1 person, with Allen key 100092 with handle 121030 (included).
White changing table with slatted ends, a rimmed changing top and two open shelves, dowelled and screwed together. Size: 82x54x93 cm. About 45–60 min, 1 person. Tools: Allen key 100092 with handle 121030 (included).
Based on the official IKEA manual AA-2580868-1 (PDF). Guide updated .
| Steps | 17 |
|---|---|
| Time | 45–60 min |
| People | 1 |
| Tools | Allen key 100092 with handle 121030 (included) |
| Size | 82x54x93 cm |
| Official manual | AA-2580868-1 |
| IKEA article number | 203.070.37 (white) |
| Pieces in the box | 81 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Slatted end frame (pre-assembled) | 2 | |
| Wide board (top unit) | 2 | |
| Short grooved rail (top unit) | 2 | |
| Changing-top panel | 1 | |
| Long shelf rail | 4 | |
| Short grooved shelf side | 4 | |
| Shelf panel (white/grey) | 2 | |
| Top rail | 2 | |
| Screw | 100215 | 16 |
| Dowel | 101350 | 20 |
| Dowel | 101375 | 24 |
| Allen key | 100092 | 1 |
| Key handle | 121030 | 1 |
Steps
- Small dowels into the top-unit rails — Steps 1–5 build the top unit. Lay the two short grooved rails on a soft surface and push two small dowels (101375) into each end, 8 in all. Use the thin 101375 dowels here, not the thicker 101350. Check: Two dowel sizes look alike: here only the thin 101375.
- Rails onto a wide board — Lay one wide board flat on the floor, holes up. Stand the two grooved rails on it, grooves facing each other, and press their dowels into the holes at its ends.
- Slide in the changing-top panel — Slide the changing-top panel down between the two rails, its edges in their grooves, until it sits in the groove of the board on the floor.
- Second wide board on top — Press the second wide board down onto the dowels at the top of the rails, with its groove over the edge of the panel.
- Big dowels into the board ends — Push one thick dowel (101350) into the free hole at each end of both wide boards, 4 in all. The second hole in each end is for a screw later. Check: Use the thick 101350 dowels here, not the thin 101375.
- Small dowels into the shelf sides — Steps 6–9 are done twice, once for each shelf. Lay two short grooved shelf sides down and push two small dowels (101375) into each end, 8 per shelf and 16 in all.
- Sides onto a long rail — Lay a long shelf rail on the floor, holes up. Stand the two shelf sides on it, grooves facing each other, and press their dowels into its holes. Do the same for the second shelf.
- Slide in the shelf panels — Slide each shelf panel down the grooves until it sits in the groove of the rail on the floor. The panel has a white and a grey side: the white side becomes the top of the shelf, the grey side faces the legs. Check: Check which side is white before sliding the panel in.
- Close the shelf frames — Press the second long rail down onto the dowels at the top of the shelf sides, its groove over the panel edge. Do the same on the second shelf.
- First end frame onto the units — Work with the table on its back. Stand one slatted end frame on its edge and push 6 thick dowels (101350) into its three cross rails. Push the top unit and both shelves onto them, shelves grey side towards the legs.
- Screw the end frame on — Slide the Allen key into its handle. Drive a screw (100215) through the leg into the end of each unit, front and back: 6 screws in all.
- Dowels into the top rails — Lay the two top rails down and push one thick dowel (101350) into the free hole at each end, 4 in all.
- Slide in the top rails — Slide one top rail along the floor edge of the top unit and the other along its upper edge, both towards the end frame, until their dowels go into the legs.
- Screw the top rails on — Drive a screw (100215) through each leg into the end of its top rail: 2 screws.
- Second end frame — Push 6 thick dowels (101350) into the cross rails of the second end frame, then push it onto the other ends of the units and top rails.
- Screw the second end frame on — Drive the last 8 screws (100215) through the legs of this end frame: one into each end of the three units and the two top rails, front and back.
- Done! — Stand the changing table up on its four legs. Your GULLIVER changing table is assembled: the rimmed top takes a changing pad, the two shelves hold nappies and towels.
GULLIVER changing table: questions and answers
How long does it take to assemble the IKEA GULLIVER changing table?
About 45–60 min for 1 person, working through the 17 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the GULLIVER changing table?
Allen key 100092 with handle 121030 (included). Already in the box: Allen key 100092 with handle 121030.
Can one person assemble the GULLIVER changing table?
Yes, it is a one-person build.
What size is the GULLIVER changing table once assembled?
82x54x93 cm, as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the GULLIVER changing table?
61 fittings of 4 kinds, the most numerous being 24 × dowel, 20 × dowel, 16 × screw. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA GULLIVER changing table assembly instructions PDF?
The official PDF is manual AA-2580868-1, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 203.070.37 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2580868-1. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example screw 100215). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA MAMMUT children's table assembly instructions
- IKEA FLISAT children's table assembly instructions
- IKEA SNIGLAR changing table assembly instructions
- IKEA RESÖ children's picnic table assembly instructions
- IKEA UTTER children's table assembly instructions
All kids assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained