Furniture hardware explained
The fittings that come in a flat-pack box, what each one does and how it goes in, with the IKEA part numbers that turn up most often across our 190 guides. Every example is a real step from an official manual.
On this page
Cam lock
A round metal disc that sits in a large hole drilled in the face of a panel. Turned with a screwdriver, its offset slot hooks the head of a cam screw from the next panel and pulls the two panels tight together. Turned back, it lets go again, which is why cam-lock furniture can be taken apart and moved.
| Used in | 66 of our 190 guides |
|---|---|
| Common part numbers | 119030 (16 guides), 103114 (8 guides), 118224 (8 guides), 113434 (8 guides) |
| Example from a manual | “Push a cam lock into each of the 4 large holes next to the lower side panel, opening towards the cam screw, and turn it clockwise with a flat screwdriver until it grips.” (BILLY bookcase, step 4) |
- How to fit it: Push it in with the opening (or arrow) towards the cam screw, then turn it until it grips. In the guides here the manuals turn it clockwise with a flat or Phillips screwdriver. Stop when it is tight: forcing it further can strip the particleboard.
- HEMNES sideboard — 42 in the box
- HEMNES 3-drawer dresser — 40 in the box
- HEMNES day-bed frame with 3 drawers — 40 in the box
- LOMMARP cabinet with glass doors — 40 in the box
- LOMMARP cabinet — 40 in the box
- ALEX drawer unit with 9 drawers — 38 in the box
Cam screw
The other half of a cam joint: a screw with a round head on a short neck. It is screwed into one panel so the head sticks out, goes into a hole in the next panel and is caught there by the cam lock.
| Used in | 64 of our 190 guides |
|---|---|
| Common part numbers | 118331 (48 guides), 123492 (6 guides), 100481 (5 guides), 130449 (3 guides) |
| Example from a manual | “Lay both side panels flat, inside (the rows of small holes) facing up and the notched ends the same way. Screw 2 cam screws in at each of the 3 board positions, 12 in total, with a Phillips screwdriver.” (BILLY bookcase, step 2) |
- How to fit it: Screw it in by hand or with a screwdriver until the collar sits on the panel, not deeper: if it goes in too far, the cam lock cannot reach the head.
- HEMNES 3-drawer dresser — 40 in the box
- HEMNES day-bed frame with 3 drawers — 40 in the box
- LOMMARP cabinet with glass doors — 40 in the box
- LOMMARP cabinet — 40 in the box
- ALEX drawer unit with 9 drawers — 38 in the box
- ALEX drawer unit — 34 in the box
Wooden dowel
A short, grooved wooden peg that fits into matching holes in two panels. Dowels line the panels up and stop them sliding; the cam locks, screws or glue hold the joint tight.
| Used in | 99 of our 190 guides |
|---|---|
| Common part numbers | 101345 (45 guides), 101350 (33 guides), 101352 (6 guides), 101375 (6 guides) |
| Example from a manual | “Lay the top, middle and bottom boards and the plinth flat. Push 4 wooden dowels into the holes in the ends of each one, 16 in total.” (BILLY bookcase, step 1) |
- How to fit it: Press them into the holes by hand. If one is stiff, tap it in gently with a hammer. Make sure each is fully in before the next panel goes on.
- MUSKAN shelving unit — 52 in the box
- HEMNES day-bed frame with 3 drawers — 51 in the box
- LOMMARP cabinet with glass doors — 50 in the box
- HEMNES sideboard — 48 in the box
- TROFAST frame — 44 in the box
- GULLIVER changing table — 44 in the box
Expansion dowel
A ribbed plastic dowel used mostly in drawer boxes. It goes through a hole in one part into the end of another and its ribs grip, so the joint holds without a screw.
| Used in | 6 of our 190 guides |
|---|---|
| Common part numbers | 110519 (6 guides) |
| Example from a manual | “Hammer 2 expansion dowels through each side into the ends of the drawer back.” (MALM chest of 3 drawers, step 32) |
- How to fit it: The manuals push or hammer it straight in through the drawer side into the drawer back. Line the parts up first: once it is in, it is hard to pull out.
- MALM chest of 3 drawers — 12 in the box
- GURSKEN chest of 3 drawers — 12 in the box
- BRIMNES bookcase — 8 in the box
- MALM chest of 2 drawers — 8 in the box
- BRIMNES dressing table — 5 in the box
- MALM dressing table — 4 in the box
Screws
Ordinary screws that cut their own thread into particleboard, fibreboard or wood: for runners, hinges, brackets, handles and back strips. Manuals often use several lengths that look alike, each with its own part number.
| Used in | 155 of our 190 guides |
|---|---|
| Common part numbers | 100214 (20 guides), 109049 (20 guides), 100365 (15 guides), 100347 (11 guides) |
| Example from a manual | “Tip the bookcase up and place it against the wall. Screw the 2 wall brackets to the top board (screw 109041 + washer 100823), then to the wall with a washer and a screw that suits your wall.” (BILLY bookcase, step 11) |
- How to fit it: Use a Phillips screwdriver and turn by hand. Several manuals here say not to use a power drill, because it can strip the hole. Check the part number on the bag when two screws look alike.
- BRIMNES day-bed frame with 2 drawers — 112 in the box
- HEMNES day-bed frame with 3 drawers — 109 in the box
- VISTHUS wardrobe — 89 in the box
- STORKLINTA chest of 6 drawers — 84 in the box
- BRIMNES chest of 4 drawers — 76 in the box
- VITVAL bunk bed frame — 76 in the box
Allen key
An L-shaped bar with a hexagonal end that turns bolts and screws with a hexagonal socket in the head. When a build needs one, the right size usually comes in the box.
| Used in | 111 of our 190 guides |
|---|---|
| Common part numbers | 100001 (45 guides), 100092 (36 guides), 100006 (14 guides), 100002 (6 guides) |
| Example from a manual | “Work on a soft surface. Stand one long side panel and one short end panel (the bottom) on their long edges at a right angle. Screw 2 screws through the end panel into the end of the side panel with the hex key.” (KALLAX shelf unit 2x4, step 1) |
- How to fit it: Use the long arm for speed and the short arm for the final turn. Keep the supplied key: the same size is needed to tighten the bolts again later.
- TUFFING bunk bed frame — 3 in the box
- SMÅSTAD loft bed frame w desk and storage — 3 in the box
- MICKE desk — 2 in the box
- BRIMNES day-bed frame with 2 drawers — 2 in the box
- MYDAL bunk bed frame — 2 in the box
- VISTHUS wardrobe — 2 in the box
Bolts and Allen screws
Machine screws with a metal thread that screw into a nut, barrel nut or threaded insert rather than into the board. Common on beds, chairs, tables and steel frames.
| Used in | 57 of our 190 guides |
|---|---|
| Common part numbers | 119976 (6 guides), 130608 (3 guides), 114334 (2 guides), 147722 (2 guides) |
| Example from a manual | “Cross the two U-shaped frames. Push the carriage bolt down through the middle (round head up, square neck in the square hole) and screw the nut on underneath, by hand only for now.” (MARIUS stool, step 1) |
- How to fit it: Start every bolt by hand so it does not cross-thread, and leave them loose until the frame is square. Where the manual says hand-tight for now, the final tightening comes in a later step.
- MYDAL bunk bed frame — 63 in the box
- VITVAL loft bed frame — 45 in the box
- EKENABBEN open shelving unit — 40 in the box
- VITVAL bunk bed frame — 39 in the box
- RÅGRUND shelving unit — 30 in the box
- SMÅSTAD loft bed frame w desk and storage — 27 in the box
Barrel nut
A metal cylinder with a threaded hole across it (a barrel nut) or along it (a sleeve nut). It sits in a hole in a rail or leg so a bolt from the next part can screw into metal instead of wood.
| Used in | 20 of our 190 guides |
|---|---|
| Common part numbers | 100602 (4 guides), 100514 (3 guides), 152526 (2 guides), 121121 (2 guides) |
| Example from a manual | “Do the same on the other rail: barrel nut into the inside hole, slot turned along the rail, then the bolt through the leg, screwed in loosely with the allen key.” (LÄTT children's table with 2 chairs, step 4) |
- How to fit it: Drop it into its hole and turn the slot so the threaded hole lines up with the bolt hole, then screw the bolt in with the Allen key.
- MYDAL bunk bed frame — 63 in the box
- SMÅSTAD loft bed frame w desk and storage — 24 in the box
- VITVAL bunk bed frame — 16 in the box
- LÄTT children's table with 2 chairs — 12 in the box
- VADHOLMA kitchen island — 12 in the box
- TROGEN children's step stool — 8 in the box
Washer
A flat ring that goes under a bolt or screw head to spread the pressure, so the head does not dig into the wood or the metal.
| Used in | 58 of our 190 guides |
|---|---|
| Common part numbers | 100823 (29 guides), 126916 (9 guides), 152651 (4 guides), 327495 (3 guides) |
| Example from a manual | “Tip the bookcase up and place it against the wall. Screw the 2 wall brackets to the top board (screw 109041 + washer 100823), then to the wall with a washer and a screw that suits your wall.” (BILLY bookcase, step 11) |
- How to fit it: Put it on the bolt before the bolt goes through the part. Where a washer has a curved side, the manual shows which way it faces.
- MARIEDAMM table — 16 in the box
- STRANDMON wing chair — 10 in the box
- LOMMARP cabinet with glass doors — 9 in the box
- SKOGSTA dining table — 8 in the box
- SKOGSTA chair — 6 in the box
- BILLY bookcase — 4 in the box
Shelf pins and supports
Small metal or plastic pins that push into a column of holes inside a bookcase or cabinet. An adjustable shelf rests on four of them, so it can be moved up or down later.
| Used in | 33 of our 190 guides |
|---|---|
| Common part numbers | 131372 (7 guides), 101532 (3 guides), 104171 (3 guides), 10051660 (3 guides) |
| Example from a manual | “Push the shelf pins into the left side panel: front and back hole, at the height you want for each of the 4 shelves (2 below the fixed middle board, 2 above it).” (BILLY bookcase, step 12) |
- How to fit it: Push all four in at the same height (count the holes from the bottom) so the shelf lies level.
- VISTHUS wardrobe — 42 in the box
- HEMNES bookcase — 20 in the box
- BILLY bookcase — 16 in the box
- NYSJÖN tall cabinet — 16 in the box
- LOMMARP cabinet with glass doors — 16 in the box
- IDANÄS cabinet with bi-folding doors — 16 in the box
Nails
Thin nails that fix the thin fibreboard back panel to the frame. On bookcases and chests the nailed back also keeps the frame square.
| Used in | 20 of our 190 guides |
|---|---|
| Common part numbers | 101221 (13 guides), 105494 (11 guides), 405950 (3 guides), 105493 (2 guides) |
| Example from a manual | “Check the dresser is square, then hammer one nail 101221 through each top corner of the back panel into the back legs, the same distance from the edge on both sides.” (HEMNES 3-drawer dresser, step 25) |
- How to fit it: Measure the frame diagonals first: when they are equal, the frame is square. Then nail along the edges, about as far apart as the manual shows, with the nails going straight into the middle of the panel edge.
- BRIMNES wardrobe with 3 doors — 61 in the box
- KLEPPSTAD wardrobe with sliding doors — 61 in the box
- RAKKESTAD wardrobe with 3 doors — 61 in the box
- BRIMNES bookcase — 31 in the box
- BAGGEBO bookcase — 31 in the box
- BRIMNES TV bench — 31 in the box
Wall fixing
A bracket, strap or rail that fixes tall furniture and chests of drawers to the wall so they cannot tip over. The bracket comes in the box; the screws and plugs for the wall often do not, because the right ones depend on the wall.
| Used in | 51 of our 190 guides |
|---|---|
| Common part numbers | 106989 (21 guides), 121714 (12 guides), 109048 (11 guides), 115753 (5 guides) |
| Example from a manual | “Tip the bookcase up and place it against the wall. Screw the 2 wall brackets to the top board (screw 109041 + washer 100823), then to the wall with a washer and a screw that suits your wall.” (BILLY bookcase, step 11) |
- How to fit it: Use screws and plugs made for your wall (wood, brick, concrete or plasterboard) and check for pipes and cables before drilling. Ask at a hardware store if you are not sure.
- NYSJÖN tall cabinet — 8 in the box
- NYSJÖN laundry cabinet — 8 in the box
- HEMNES 3-drawer dresser — 6 in the box
- MALM chest of 3 drawers — 6 in the box
- MALM dressing table — 6 in the box
- HAUGA wardrobe with sliding doors — 6 in the box
Angle bracket
A small L-shaped bracket screwed into two parts that meet at a right angle, such as a plinth and a side panel or a top and a rail.
| Used in | 27 of our 190 guides |
|---|---|
| Common part numbers | 102553 (5 guides), 103717 (5 guides), 102720 (4 guides), 10038685 (3 guides) |
| Example from a manual | “Hold an angle bracket (120298) on each marked hole, tab pointing towards the inside of the table, and screw it to the leg with the longer screw 108530.” (LACK coffee table, step 4) |
- How to fit it: Fit it flush with the edge the manual shows, then drive both screws in straight.
- BROR trolley — 12 in the box
- BROR work bench — 12 in the box
- BEKVÄM kitchen trolley — 8 in the box
- RÅGRUND towel rack/chair — 6 in the box
- LACK coffee table — 4 in the box
- BRIMNES bookcase — 4 in the box
Hinge and mounting plate
Cabinet doors mostly hang on concealed cup hinges: the cup sits in a round hole in the door and clips or screws onto a mounting plate inside the cabinet. Screws on the hinge move the door up and down, sideways and in and out.
| Used in | 32 of our 190 guides |
|---|---|
| Common part numbers | 109221 (3 guides), 109338 (3 guides), 144553 (3 guides), 109220 (2 guides) |
| Example from a manual | “Screw the 2 hinge mounting plates onto the inside of the outer cabinet side with 2 screws 113287 each.” (MICKE desk, step 16) |
- How to fit it: Fit the hinges to the door first, then hang the door with a helper holding it. If the doors are crooked or the gap is uneven, adjust them with the hinge screws once the cabinet stands where it will stay.
- BRIMNES wardrobe with 3 doors — 18 in the box
- RAKKESTAD wardrobe with 3 doors — 18 in the box
- IDANÄS wardrobe — 12 in the box
- RAKKESTAD wardrobe with 2 doors — 12 in the box
- BRIMNES cabinet with doors — 8 in the box
- VISTHUS wardrobe — 8 in the box
Drawer runner
The rails a drawer rolls on: one part is screwed inside the cabinet, its partner to the drawer. Runners are usually made for one side only, left or right.
| Used in | 39 of our 190 guides |
|---|---|
| Common part numbers | 112482 (4 guides), 158933 (4 guides), 139505 (3 guides), 10103402 (2 guides) |
| Example from a manual | “Place a drawer runner along the edge of each drawer side, with the wheel at the back end of the drawer.” (MICKE desk, step 7) |
- How to fit it: Check the left and right labels and which end the wheel goes, as the manual shows. If a drawer will not close, the runners are often swapped or the drawer is not square.
- BRIMNES chest of 3 drawers — 9 in the box
- MALM chest of 3 drawers — 8 in the box
- BRIMNES bookcase — 8 in the box
- BRIMNES chest of 4 drawers — 8 in the box
- ALEX desk — 6 in the box
- GURSKEN chest of 3 drawers — 6 in the box
Glide
A small plastic or felt foot pressed or tapped into the bottom edge of a panel or leg, so the furniture slides without scratching the floor.
| Used in | 44 of our 190 guides |
|---|---|
| Common part numbers | 153548 (16 guides), 158568 (12 guides), 122628 (3 guides), 153552 (2 guides) |
| Example from a manual | “Press the 4 glides 153549 into the bottom edges of the two cabinet sides.” (MICKE desk, step 28) |
- How to fit it: Press it in by hand or tap it with a hammer until it sits flat.
- RAKKESTAD wardrobe with 3 doors — 8 in the box
- STORKLINTA chest of 6 drawers — 7 in the box
- MALM chest of 3 drawers — 6 in the box
- MALM bed frame (high, Queen) — 6 in the box
- BRIMNES wardrobe with 3 doors — 6 in the box
- NORDEN gateleg table — 6 in the box
Adjustable foot
A foot that screws in or out so the furniture stands level on an uneven floor.
| Used in | 19 of our 190 guides |
|---|---|
| Common part numbers | 122158 (3 guides), 131399 (3 guides), 10056734 (2 guides), 107862 (2 guides) |
| Example from a manual | “Screw an adjustable foot 102728 by hand into the bottom end of each post: 2 per frame, 4 in total.” (HEMNES bookcase, step 5) |
- How to fit it: Screw them all in the same amount, stand the furniture in place, then adjust with a spirit level.
- FJÄLLBO TV bench — 8 in the box
- FJÄLLBO shelving unit — 6 in the box
- VISTHUS wardrobe — 6 in the box
- IDANÄS wardrobe — 5 in the box
- IDANÄS cabinet with bi-folding doors — 5 in the box
- PAX wardrobe frame — 4 in the box
Castor
A small wheel under a trolley, drawer unit or bed so it can be moved around. Some castors have a brake.
| Used in | 19 of our 190 guides |
|---|---|
| Common part numbers | 111401 (3 guides), 10054852 (1 guide), 122567 (1 guide), 10121215 (1 guide) |
| Example from a manual | “Turn the trolley upside down so it stands on the closed ends of the frames. Push a castor (10054852) into each of the 4 open tube ends until it clicks.” (NISSAFORS trolley, step 11) |
- How to fit it: Push or screw it fully into its socket; the manual shows which ones have the brake and where they go.
- MICKE drawer unit with drop-file storage — 14 in the box
- HEMNES day-bed frame with 3 drawers — 8 in the box
- VISTHUS wardrobe — 8 in the box
- BRIMNES day-bed frame with 2 drawers — 6 in the box
- ÖRFJÄLL children's desk chair — 5 in the box
- NISSAFORS trolley — 4 in the box
Bumpers and door stops
Small soft pads stuck or pressed inside a cabinet so doors and drawers close quietly and stop in the right place.
| Used in | 33 of our 190 guides |
|---|---|
| Common part numbers | 107091 (14 guides), 108787 (3 guides), 104663 (2 guides), 123840 (2 guides) |
| Example from a manual | “Stick the 2 hexagonal felt pads 10081375 under the leg frame. (The round bumpers are used later.)” (MICKE desk, step 29) |
- How to fit it: Stick them on a clean, dry surface in the spots the manual marks.
- VITTSJÖ shelving unit — 12 in the box
- HAUGA wardrobe with sliding doors — 11 in the box
- KLEPPSTAD wardrobe with sliding doors — 11 in the box
- VITTSJÖ coffee table — 6 in the box
- LOMMARP cabinet — 6 in the box
- BRIMNES wardrobe with 3 doors — 5 in the box
Cover caps
Plastic caps pressed over screw heads, cam locks or unused holes to hide them.
| Used in | 56 of our 190 guides |
|---|---|
| Common part numbers | 10093082 (9 guides), 115754 (4 guides), 152650 (4 guides), 10043569 (3 guides) |
| Example from a manual | “Hook each cover cap over its corner fitting and swing it in until it clicks.” (PAX wardrobe frame, step 20) |
- How to fit it: Fit them last, once everything is tight: they are hard to get off again.
- STORKLINTA chest of 6 drawers — 20 in the box
- SMUSSLA bedside table/shelf unit — 17 in the box
- LOMMARP cabinet with glass doors — 16 in the box
- HAUGA wardrobe with sliding doors — 14 in the box
- HAUGA cabinet with 2 doors — 12 in the box
- ENHET wall frame with shelves — 10 in the box
Knobs and handles
Fixed to the drawer front or door with a screw from the inside.
| Used in | 56 of our 190 guides |
|---|---|
| Common part numbers | 121030 (12 guides), 150689 (6 guides), 141414 (5 guides), 117615 (4 guides) |
| Example from a manual | “Turn the drawers upright. Hold a knob 117615 against the front and screw it on from the inside with a screw 119976: 2 knobs per drawer.” (HEMNES 3-drawer dresser, step 40) |
- How to fit it: Fit them before the drawer goes in, while you can still reach the back of the front.
- HEMNES 3-drawer dresser — 12 in the box
- VISTHUS wardrobe — 11 in the box
- STÄLL shoe cabinet with 4 compartments — 8 in the box
- HEMNES TV bench — 7 in the box
- VIHALS sideboard — 6 in the box
- IDÅSEN cabinet with doors and drawers — 6 in the box
Hardware questions
Which way do you turn a cam lock?
In the manuals behind these guides, cam locks are turned clockwise with a screwdriver until they grip the cam screw. Turning one back the other way releases it, for example to take the furniture apart. Stop when it is tight.
What is the difference between a cam lock and a dowel?
Dowels only line the panels up and stop them sliding. The cam lock and its cam screw are what pull the panels together and hold them. Most cam-lock joints use both.
I have screws left over. Is that a problem?
Count them against the In the box list of your guide: several manuals include a spare, and some fittings are only for other versions. If a fitting the list shows is still in the bag, find the step that uses it before you go on.
A fitting is missing. Where do I get one?
Check all the boxes and the packaging first: small fittings are often taped inside. Every fitting in our In the box lists carries its IKEA part number, and IKEA customer service can send replacements by that number.
Can I use a power drill?
Several manuals here say not to, because a drill can strip the hole in particleboard or overtighten a pivot. A hand screwdriver is safer; if you use a drill, set the lowest clutch setting and finish by hand.