Step by StepAssembly Find your furniture

IKEA MALM chest of 2 drawers assembly instructions

How to assemble the IKEA MALM chest of 2 drawers (dresser), step by step: 23 animated steps built from the official manual, about 1–1.5 hours for 1 person, with flat & Phillips screwdriver, hammer.

IKEA MALM chest of 2 drawers, assembled

The small MALM bedside chest: a cam-lock frame built on its side, a nailed-on back panel and two drawers on wheeled runners. Size: 40×48×55 cm. About 1–1.5 hours, 1 person. Tools: Flat & Phillips screwdriver, Hammer.

Based on the official IKEA manual AA-2596665-2 (PDF). Guide updated .

MALM chest of 2 drawers: quick facts
Steps23
Time1–1.5 hours
People1
ToolsFlat & Phillips screwdriver, Hammer
Size40×48×55 cm
Official manualAA-2596665-2
IKEA article number906.253.19 (white)
Pieces in the box138

In the box

PartPart numberQuantity
Side panel (runners fitted)2
Top1
Front rail3
Bottom back rail (raw)1
Back panel1
Drawer front2
Drawer side4
Drawer back2
Drawer bottom2
Cam screw11833120
Wooden dowel10134520
Cam lock12007620
Glide1535484
Nail10122130
Expansion dowel1105198
Screw1153394
Screw10036512
Drawer runner pair 10056137 (DL + DR)2

Steps

  1. Cam screws into the side panels — Lay both side panels on a soft surface, inside (runner side) up. Screw 4 cam screws into the small holes of each panel with a Phillips screwdriver. Check: Work on a rug or the empty box so the panels do not get scratched.
  2. Glides under the side panels — Press 2 glides into the bottom edge of each side panel, one near each end.
  3. Dowels and the 4 rails — Push a dowel into each end of the 3 white front rails and the raw bottom back rail. Stand them on the left side panel: the front rails along the front edge, the raw rail flat at the bottom of the back edge. Check: The raw (unfinished) rail goes at the back, where it will be hidden.
  4. Lock the rails to the left side — Put a cam lock into the hole at the lower end of each rail, arrow pointing to the cam screw, and turn it clockwise with a flat screwdriver until it locks.
  5. Right side panel on top — Turn the second side panel over, runners facing down, and lower it onto the 4 rails so the dowels and cam screws go into their holes. Check: The panel’s back edge has a rebate for the back panel: it must line up with the rebate of the first panel.
  6. Tip it onto its back; lock the right side — Tip the frame over so it lies on its back with the front rails on top. Insert 4 cam locks at the right-hand ends of the rails and turn each one to lock.
  7. Stand it up; cam screws into the top — Stand the frame upright on its glides. Lay the top upside down on a soft surface and screw the 4 cam screws into the holes near its side edges.
  8. Fit the top — Push 4 dowels into the top edges of the side panels, then turn the top over and press it down onto them. Check: The top’s plain edge goes to the front; the groove underneath goes to the back, as the manual’s right/wrong close-up shows.
  9. Lock the top — Insert 4 cam locks in the inside faces of the side panels just under the top and turn them clockwise to lock.
  10. Lay it on its front, back panel on — Lay the chest face down. Put the back panel on, push it into the groove under the top and against the left side panel, and nail that top corner. Check: Keep the panel pushed into the groove and square with the side while you nail.
  11. Nail the bottom corner on the same side — Keep the panel pushed towards the top and nail the bottom corner on the same side.
  12. Nail the other top corner — Push the panel square against the other side panel and nail that top corner.
  13. Nail the back panel all round — Drive in the other 27 nails all round the four edges, using the holes marked on the panel.
  14. Stand it up; cam screws into drawer front 1 — Stand the chest upright. For each of the 2 drawers: lay the drawer front face down on a soft surface and screw 4 cam screws into it.
  15. Dowels; sides onto the front — Push 2 dowels into the front end of each drawer side. Stand both sides on the front, dowels and cam screws into their holes, grooves facing in.
  16. Lock the drawer sides — Insert 4 cam locks on the inside of the sides and turn them clockwise to lock onto the cam screws.
  17. Slide in the drawer bottom — Slide the drawer bottom down into the grooves in the sides, all the way to the front.
  18. Fit the drawer back — Bring the drawer back over the open end and slide it in between the sides until it rests on the drawer bottom, cut-outs at the bottom as the close-up shows.
  19. Expansion dowels and stop screws — Hammer 2 expansion dowels through each side into the ends of the drawer back. Then screw a small screw 115339 into the front, just outside each side at the bottom.
  20. Turn it over; runners on — Turn the drawer upside down on a table. Lay runner DL on the left side and DR on the right, and fix each with 3 screws through its flange into the side. Check: The runners are marked DL (left) and DR (right): check the labels before screwing.
  21. Drawer 2: the same again — Lift the finished drawer off the table. Build the second drawer exactly the same way (steps 14–20).
  22. Slide in the drawers — Fit each drawer: hold it with the front tipped up, set its wheels on the runners in the frame, then lower the front and push it all the way in. Check: Never open more than one drawer at a time, and put the heaviest things in the bottom drawer.
  23. Done! — Your MALM chest of 2 drawers is assembled.

MALM chest of 2 drawers: questions and answers

How long does it take to assemble the IKEA MALM chest of 2 drawers?

About 1–1.5 hours for 1 person, working through the 23 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the MALM chest of 2 drawers?

Flat & Phillips screwdriver, hammer.

Can one person assemble the MALM chest of 2 drawers?

Yes, it is a one-person build.

What size is the MALM chest of 2 drawers once assembled?

40×48×55 cm, as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the MALM chest of 2 drawers?

118 fittings of 8 kinds, the most numerous being 30 × nail, 20 × cam screw, 20 × wooden dowel. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA MALM chest of 2 drawers assembly instructions PDF?

The official PDF is manual AA-2596665-2, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 906.253.19 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2596665-2. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example cam screw 118331). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA MALM assembly guides · All dressers & drawers assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained