IKEA MALM dressing table assembly instructions
How to assemble the IKEA MALM dressing table, step by step: 26 animated steps built from the official manual, about 1–2 hours for 2 people, with flat & Phillips screwdriver, hammer, pencil, drill (for the wall fixing).
A high-gloss MALM dressing table: thick leg panels bolted to the top, a loose glass plate held by clips, wall anchoring and one wide drawer on concealed runners. Size: 120×41×78 cm. About 1–2 hours, 2 people. Tools: Flat & Phillips screwdriver, Hammer, Pencil, Drill (for the wall fixing).
Based on the official IKEA manual AA-2601226-4 (PDF). Guide updated .
| Steps | 26 |
|---|---|
| Time | 1–2 hours |
| People | 2 |
| Tools | Flat & Phillips screwdriver, Hammer, Pencil, Drill (for the wall fixing) |
| Size | 120×41×78 cm |
| Official manual | AA-2601226-4 |
| IKEA article number | 905.774.36 (white high gloss) |
| Pieces in the box | 67 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Top | 1 | |
| Leg panel | 2 | |
| Glass plate | 1 | |
| Drawer front | 1 | |
| Drawer side | 2 | |
| Drawer back | 1 | |
| Drawer bottom | 1 | |
| Drawer mat | 1 | |
| Hanger bolt | 114334 | 4 |
| Spanner | 113453 | 1 |
| Drawer runner pair 10139543 + 10139504 (pack 118250) | 1 | |
| Screw | 100349 | 4 |
| Dowel 101353 (large) | 2 | |
| Wedge | 122998 | 4 |
| Flange nut | 114254 | 4 |
| Glide | 153548 | 4 |
| Wall bracket | 106989 | 2 |
| Screw | 109049 | 2 |
| Washer | 100823 | 4 |
| Wall screw | 109048 | 2 |
| Wall plug | 121714 | 2 |
| Glass clip | 10003193 | 3 |
| Screw | 109560 | 3 |
| Cam screw | 118331 | 2 |
| Dowel 101345 (small) | 2 | |
| Cam lock | 110630 | 2 |
| Screw | 105344 | 2 |
| Centre support | 152123 | 1 |
| Expansion dowel | 110519 | 4 |
| Screw | 109558 | 2 |
Steps
- Hanger bolts into the top — Lay the top upside down on a rug or the flattened box. Screw the 4 hanger bolts into the holes near the ends, wood-screw end first, using the open end of the supplied spanner on each bolt’s hex collar. Check: Turn each bolt in until its collar sits on the surface, as the manual’s detail shows.
- Drawer runners on the legs — Lay both leg panels flat, inside face up. Place a drawer runner over the pre-drilled holes near the top end of each leg and fix it with 2 screws. Check: The two runners are a left and a right one: each goes on the leg where its wheel end points to the front.
- Dowels in, legs onto the bolts — Push the 2 large dowels into the holes between the bolts. Stand each leg upside down on the top, the runner on the inside, so the bolts and the dowel go into the holes in its top edge. Check: Use the large dowels 101353 here, not the small 101345 (those are for the drawer).
- Wedges and nuts in the round holes — In each round hole on the inside of the legs, put a wedge over the bolt end and screw a flange nut onto the bolt. Tighten the nuts with the ring end of the spanner. Check: Tighten all 4 nuts firmly so the legs sit tight against the top.
- Glides into the legs — Tap 2 glides into the holes in the bottom edge of each leg with a hammer.
- Wall brackets, then turn it over — Screw a wall bracket to the underside of the top at its back edge, next to each leg, with a screw 109049 and a washer 100823. Then carefully turn the table over onto its legs. Check: Two people should turn the table over.
- Remove the protective film — Peel the protective film off the top and off the legs.
- Lay the glass plate on — Lay the glass plate on the top, with its 3 holes along the back edge (the side with the wall brackets). Check: Handle the glass with care and never put weight on its edges.
- Glass clips — Push the round peg of a clip into each of the 3 holes in the glass, with the tab hanging down over the back edge of the top.
- Screw the clips to the top — Mark through the hole in each clip’s tab with a pencil, then screw a screw 109560 through each tab into the back edge of the top. Check: The manual draws steps 7–10 from the back of the table; turn it back round before you take it to the wall.
- At the wall: mark the holes — Stand the table against the wall where it will stay. Reach in under the top and mark the wall through the slot of each wall bracket. Check: Check for hidden pipes and cables before you drill.
- Move the table away — Move the table away from the wall so you can drill at the two marks.
- Drill and plug the wall — Drill a hole at each mark and tap in a wall plug. The plugs and screws supplied suit most solid and hollow walls; in solid wood use the screws without plugs and a 3 mm drill. Check: If you are not sure which fixings suit your wall, ask a specialist.
- Fix it to the wall — Push the table back. At each bracket: loosen the bracket screw, drive a wall screw 109048 with a washer 100823 through the slot into the plug, then tighten the bracket screw again. Check: Always anchor the table to the wall.
- Drawer: cam screws into the front — Lay the drawer front face down on a soft surface. Screw a cam screw into the hole at each end of its inside face.
- Drawer sides on — Push a small dowel 101345 into the front end of each drawer side. Stand the sides on the ends of the front, dowels and cam screws into their holes.
- Lock the drawer sides — Put a cam lock into the hole in the outside of each side and turn it clockwise with a flat screwdriver until it locks onto the cam screw.
- Screw for the centre support — Screw a screw 105344 into the hole in the middle of the front, below the groove. Leave the head standing a few millimetres proud. Check: Do not screw it all the way in yet: the centre support hooks in under its head.
- Hook on the centre support — Slide the hooked end of the centre support in under the screw head, the support running along the middle of the drawer. Then tighten the screw. Check: Let the support hang a little away from the drawer for now, so the bottom and the back can go in.
- Slide in the drawer bottom — Slide the drawer bottom down into the grooves in the sides and the front, printed side facing into the drawer, over the centre support.
- Back on, expansion dowels — Put the drawer back between the sides on top of the bottom. Hammer 2 expansion dowels through each side into the ends of the back.
- Screw the centre support to the back — Swing the centre support up so its bent end lies against the back. Mark through the hole, then fix it with the second screw 105344.
- Turn it upright, film off, mat in — Turn the drawer the right way up. Peel the protective film off the drawer front, then lay the mat into the drawer.
- Fit the drawer — Pull both runners all the way out. Set the drawer on them, its back over the runners’ rear hooks, then press the front down until the locks under it click. Push it in. Check: The wheels on the runner locks under the drawer adjust its height if the gap under the top is uneven.
- Screw the runner locks — Pull the drawer out. From underneath, drive a screw 109558 up through the hole next to each runner lock into the drawer. Push the drawer back in.
- Done! — Your MALM dressing table is assembled and fixed to the wall.
MALM dressing table: questions and answers
How long does it take to assemble the IKEA MALM dressing table?
About 1–2 hours for 2 people, working through the 26 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the MALM dressing table?
Flat & Phillips screwdriver, hammer, pencil, drill (for the wall fixing).
Can one person assemble the MALM dressing table?
It is planned as a 2-person build. One person can do most of it, but get help for step 6, where the furniture is lifted or turned.
Does the MALM dressing table need to be fixed to the wall?
The manual shows a wall fixing: see step 6 (Wall brackets, then turn it over) and step 14 (Fix it to the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.
What size is the MALM dressing table once assembled?
120×41×78 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.
How many screws and fittings come with the MALM dressing table?
51 fittings of 18 kinds, the most numerous being 4 × hanger bolt, 4 × screw, 4 × wedge. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA MALM dressing table assembly instructions PDF?
The official PDF is manual AA-2601226-4, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 905.774.36 (white high gloss); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2601226-4. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example hanger bolt 114334). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA MALM chest of 3 drawers assembly instructions
- IKEA MALM bed frame (high, Queen) assembly instructions
- IKEA MALM chest of 2 drawers assembly instructions
- IKEA HEMNES 3-drawer dresser assembly instructions
- IKEA ALEX drawer unit assembly instructions
- IKEA LENNART drawer unit assembly instructions
- IKEA BRIMNES bedside table assembly instructions
- IKEA ALEX drawer unit on castors assembly instructions
All IKEA MALM assembly guides · All dressers & drawers assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained