Step by StepAssembly Find your furniture

IKEA MALM chest of 3 drawers assembly instructions

How to assemble the IKEA MALM chest of 3 drawers (dresser), step by step: 41 animated steps built from the official manual, about 2–3 hours for 2 people, with flat & Phillips screwdriver, hammer, pencil, drill (for the wall fixing).

IKEA MALM chest of 3 drawers, assembled

The classic MALM dresser: a cam-lock frame on a plinth, a nailed-on back panel, wall anchoring and three drawers on runners. Size: 80×48×78 cm. About 2–3 hours, 2 people. Tools: Flat & Phillips screwdriver, Hammer, Pencil, Drill (for the wall fixing).

Based on the official IKEA manual AA-2586928-1 (PDF). Guide updated .

MALM chest of 3 drawers: quick facts
Steps41
Time2–3 hours
People2
ToolsFlat & Phillips screwdriver, Hammer, Pencil, Drill (for the wall fixing)
Size80×48×78 cm
Official manualAA-2586928-1, AA-2603131-1
IKEA article number806.173.05 (white)
Pieces in the box213

In the box

PartPart numberQuantity
Side panel (runners fitted)2
Top1
Plinth1
Front rail3
Board (bottom/middle)2
Back panel (folding fibreboard)1
Drawer front3
Drawer side6
Drawer back3
Drawer bottom3
Cam screw11833126
Wooden dowel10134530
Cam lock 117434/119030/12007626
Screw1556698
Angle bracket100386852
Glide 153548/1585686
Nail10122130
Expansion dowel11051912
Screw1153396
Screw10036518
Screw1053446
Drawer runner pair 118790 +1486013
Drawer rail1238333
Wall bracket1069892
Screw1090492
Washer1008234
Wall screw1090482
Wall plug1217142

Steps

  1. Cam screws into the side panels — Lay both side panels on a rug or the empty box, inside (runner side) up. Screw 5 cam screws into the small holes of each panel with a Phillips screwdriver. Check: Work on a soft surface so the panels do not get scratched.
  2. Glides under the side panels — Press 2 glides into the bottom edge of each side panel, one near the front and one near the back.
  3. Angle brackets on the plinth — Lay the plinth on its front. Put an angle bracket at each end, the upright leg flush with the end, and fix each with 2 screws.
  4. Glides under the plinth — Press a glide into the bottom edge of the plinth at each end.
  5. Plinth onto the first side panel — Stand the plinth on edge at the bottom front corner of the side panel, brackets inside. Screw the bracket to the panel with 2 screws. Check: The plinth must be flush with the panel’s front and bottom edges, not sticking out past them.
  6. Dowels and the 3 front rails — Push a wooden dowel into each end of the 3 front rails. Stand the rails on edge along the front of the side panel, dowels into the holes and over the cam screws.
  7. Lock the rails — Put a cam lock into the hole at the bottom end of each rail and turn it clockwise with a flat screwdriver until it locks onto the cam screw.
  8. Bottom board — Push 4 dowels into the ends of the bottom board. Stand it on edge on the side panel just behind the plinth, over the cam screws near the back edge. Check: Check the board’s orientation: the round cam lock holes face the top end of the chest and sit at the back edge, as the manual’s right/wrong drawing shows.
  9. Lock the bottom board — Insert 1 cam lock in the hole on the top face of the bottom board, at the back edge, and turn it clockwise to lock it onto the cam screw.
  10. Middle board — Push 4 dowels into the middle board and stand it on edge behind the lowest front rail, the same way round as the bottom board.
  11. Lock the middle board — Insert 1 cam lock in the hole on the top face of the middle board, at the back edge, and turn it to lock.
  12. Second side panel on top — Turn the second side panel over, runners facing down, and lower it onto the rails, boards and plinth so all the dowels and cam screws go into their holes. Check: Two people make this easier.
  13. Screw the plinth to the second side — Fix the plinth’s other angle bracket to the side panel with 2 screws.
  14. Lock the second side — Insert 5 cam locks at this end of the 3 rails and 2 boards, and turn each one to lock it.
  15. Stand it up; cam screws into the top — Carefully stand the frame upright. Lay the top upside down on a soft surface and screw the 4 cam screws into the holes near its ends. Check: Two people are needed to stand the frame up.
  16. Wall brackets on the top — Screw the 2 wall brackets to the underside of the top at its back edge, each with a screw 109049 and a washer 100823.
  17. Fit the top — Push 4 dowels into the top edges of the side panels. Turn the top over and press it down onto the dowels, with the wall brackets at the back. Check: The top’s profiled edge goes to the front, as shown in the manual.
  18. Lock the top — Insert 4 cam locks in the inside faces of the side panels just under the top and turn them to lock.
  19. Lay it on its front, back panel on — Lay the chest face down. Unfold the back panel and lay it on the back, pushing its top edge into the groove under the top. Fix one top corner with a nail. Check: Line the back panel up with the side panels’ edges before nailing.
  20. Nail the other top corner — Keep the panel pushed into the groove and nail the other top corner.
  21. Nail a bottom corner — Push the panel square with the side edge and nail one bottom corner.
  22. Nail the back panel all round — Drive in the other 27 nails all round the four edges, using the holes marked on the panel.
  23. Stand it at the wall and mark — Stand the chest up against the wall where it will stay. Reach in through the top drawer opening and mark the wall through each bracket’s slot. Check: Check for hidden pipes and cables before you drill.
  24. Move it away, drill, plugs in — Move the chest aside. Drill a hole at each mark and tap in the 2 wall plugs with a hammer (for solid walls; use fixings that suit your wall). Check: The plugs and screws in the box suit solid walls. For plasterboard or wood, use fixings that suit the wall.
  25. Fix it to the wall — Push it back. At each bracket: loosen the bracket screw, drive a wall screw 109048 + washer 100823 into the plug, retighten. Check: Always anchor it: a tipping chest can kill. Never let children climb it.
  26. Drawer 1: cam screws into the front — Now build the drawers (separate drawer manual). Lay a drawer front face down on a soft surface and screw 4 cam screws into it.
  27. Dowels into the drawer sides — Lay out the two drawer sides and push 2 dowels into the front end of each.
  28. Sides onto the front — Stand both sides on the drawer front, dowels and cam screws into their holes. The side with the warning label goes on the left, label facing in. Check: The warning label reminds you: never open more than one drawer at a time.
  29. Lock the drawer sides — Insert 4 cam locks on the inside of the sides and turn them to lock onto the cam screws.
  30. Slide in the drawer bottom — Slide the drawer bottom down into the grooves in the sides, all the way to the front.
  31. Fit the drawer back — Put the drawer back between the sides, on top of the bottom, with its cut-outs facing the bottom as shown.
  32. Expansion dowels — Hammer 2 expansion dowels through each side into the ends of the drawer back.
  33. Stop screws in the front — Screw a small screw 115339 into the back of the front, just outside each side at the bottom.
  34. Turn it over; runners on — Turn the drawer upside down on a table, front over the edge. Lay a runner on the bottom edge of each side, wheel at the back, hooked behind the stop screw.
  35. Screw the runners on — Fix each runner with 3 screws through its side flange.
  36. Centre rail: front end — Screw a screw 105344 part-way into the back of the front, under the bottom. Hook the slotted end of the rail under its head and swing the rail down along the middle.
  37. Centre rail: back end — Mark through the hole of the rail’s bent end on the drawer back, then fix it with a screw 105344.
  38. Drawer 2: the same again — Lift the finished drawer off the table. Build the second drawer exactly the same way (drawer manual steps 1–12).
  39. Drawer 3: the same again — Lift drawer 2 off the table and build the third drawer the same way.
  40. Slide in the drawers — Fit each drawer into the chest: set its runners on the runners in the frame and push it all the way in. Check: Never open more than one drawer at a time, and put the heaviest things in the bottom drawer.
  41. Done! — Your MALM chest of 3 drawers is assembled and anchored to the wall.

MALM chest of 3 drawers: questions and answers

How long does it take to assemble the IKEA MALM chest of 3 drawers?

About 2–3 hours for 2 people, working through the 41 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the MALM chest of 3 drawers?

Flat & Phillips screwdriver, hammer, pencil, drill (for the wall fixing).

Can one person assemble the MALM chest of 3 drawers?

It is planned as a 2-person build. One person can do most of it, but get help for steps 12, 15 and 17, where the furniture is lifted or turned.

Does the MALM chest of 3 drawers need to be fixed to the wall?

The manual shows a wall fixing: see step 16 (Wall brackets on the top) and step 25 (Fix it to the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the MALM chest of 3 drawers once assembled?

80×48×78 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the MALM chest of 3 drawers?

188 fittings of 18 kinds, the most numerous being 30 × wooden dowel, 30 × nail, 26 × cam screw. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA MALM chest of 3 drawers assembly instructions PDF?

The official PDF is manual AA-2586928-1, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 806.173.05 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2586928-1 (drawers: AA-2603131-1). Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example cam screw 118331). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA MALM assembly guides · All dressers & drawers assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained