IKEA LENNART drawer unit assembly instructions
How to assemble the IKEA LENNART drawer unit, step by step: 14 animated steps built from the official manual, about 30–45 min for 1 person, with Phillips screwdriver.
The slim LENNART drawer unit in white: a steel tube frame with a mesh top, two castors at the back and three mesh drawers folded from flat and clicked together. Size: 30×34×56 cm (11 3/4×13 3/8×22"). About 30–45 min, 1 person. Tools: Phillips screwdriver.
Based on the official IKEA manual AA-490876-9 (PDF). Guide updated .
| Steps | 14 |
|---|---|
| Time | 30–45 min |
| People | 1 |
| Tools | Phillips screwdriver |
| Size | 30×34×56 cm (11 3/4×13 3/8×22") |
| Official manual | AA-490876-9 |
| IKEA article number | 303.261.77 (white) |
| Pieces in the box | 72 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Side frame with runners | 2 | |
| Bottom rail | 2 | |
| Mesh top panel | 1 | |
| Cross brace | 2 | |
| Drawer: folding bottom, front, back | 3 | |
| Screw | 116654 | 12 |
| Castor | 122567 | 2 |
| Plastic plug | 10050916 | 24 |
| Plastic pin | 10050917 | 24 |
Steps
- Side frames and bottom rails — Stand the two side frames on their front edges, parallel to each other, with the runners facing inwards and the posts with the small holes on top. Place the two bottom rails across the lower ends of the posts, one between the upper posts and one between the lower posts. Check: The posts with the holes near the top end are the back posts: keep them facing up.
- Screw the bottom rails — Drive a screw 116654 through the hole at each end of both rails into the end of the post, turning clockwise with a Phillips screwdriver: 4 screws in total.
- Stand it up, fit the top — Stand the frame upright on the bottom rails. Lower the mesh top panel straight down so the four posts go into its folded edge.
- Screw the top panel — Fix the top with 4 screws 116654, one through each corner of its side edges into the post below, turned clockwise with the screwdriver.
- Cross braces on the back — Lay the unit on its front. Place the two cross braces diagonally over the back, crossing each other, with their eyes over the holes in the back posts. Screw them on with 4 screws 116654.
- Castors, then stand it up — Push a castor 122567 firmly into the open lower end of each back post until it sits tight. Then tip the unit up onto its castors and front feet. Check: The castors go in by hand, no tool needed.
- Drawers: fold up the first side — Now build the 3 drawers, all the same way. Lay a drawer bottom flat with its folded edges pointing down to the floor. Hold the middle down and fold one side up along the perforated line until it stands upright. Check: Check the edges: the folded lips must point down (manual page 6). With the lips up, the drawer can’t be assembled.
- Drawers: fold up the second side — Fold the other side up the same way, so the drawer bottom and its two sides form a U.
- Drawers: front and back — Slide a drawer front onto one open end and a drawer back onto the other, so their side channels hook over the folded edges of the sides.
- Drawers: click in the plugs — Lock the drawer with 8 plastic plugs 10050916 and 8 pins 10050917. Push a plug into each hole, then press a pin into the plug until it clicks: 4 down through the corners of the bottom, where the front and back overlap it, and 4 through the sides near the top, into the side channels of the front and back.
- Drawers: plugs in the other two — Lock the other two drawers the same way: 8 plugs and 8 pins each, 24 of each for all three drawers.
- Hang in the bottom drawer — Lift a drawer and hold it level in front of the lowest place. Set the folded top edges of its sides into the runners of the frame and slide it all the way in.
- Hang in the other two drawers — Hang the other two drawers in the same way: the middle one, then the top one.
- Done! — Your LENNART drawer unit is ready. Each drawer holds up to 5 kg.
LENNART drawer unit: questions and answers
How long does it take to assemble the IKEA LENNART drawer unit?
About 30–45 min for 1 person, working through the 14 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the LENNART drawer unit?
Phillips screwdriver.
Can one person assemble the LENNART drawer unit?
Yes, it is a one-person build.
What size is the LENNART drawer unit once assembled?
30×34×56 cm (11 3/4×13 3/8×22"), as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the LENNART drawer unit?
62 fittings of 4 kinds, the most numerous being 24 × plastic plug, 24 × plastic pin, 12 × screw. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA LENNART drawer unit assembly instructions PDF?
The official PDF is manual AA-490876-9, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 303.261.77 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-490876-9. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example screw 116654). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA HEMNES 3-drawer dresser assembly instructions
- IKEA MALM chest of 3 drawers assembly instructions
- IKEA ALEX drawer unit assembly instructions
- IKEA MALM dressing table assembly instructions
- IKEA BRIMNES bedside table assembly instructions
- IKEA ALEX drawer unit on castors assembly instructions
- IKEA STORKLINTA chest of 2 drawers assembly instructions
- IKEA EKET cabinet with 2 drawers assembly instructions
All dressers & drawers assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained