Step by StepAssembly Find your furniture

IKEA EKET cabinet with 2 drawers assembly instructions

How to assemble the IKEA EKET cabinet with 2 drawers, step by step: 29 animated steps built from the official manual, about 1–1.5 hours for 1 person, with Phillips screwdriver, hammer, drill with Ø 8 mm bit, spirit level, wall screws and plugs (not included).

IKEA EKET cabinet with 2 drawers, assembled

White EKET cabinet with two push-to-open drawers: four mitred panels that hook together without screws, a slide-in back panel held by clips, full-extension runners and wall fixing with adjustable spacers. Size: 70×35×35 cm (27 1/2×13 3/4×13 3/4"). About 1–1.5 hours, 1 person. Tools: Phillips screwdriver, Hammer, Drill with Ø 8 mm bit, Spirit level, Wall screws and plugs (not included).

Based on the official IKEA manual AA-2345060-3 (PDF). Guide updated .

EKET cabinet with 2 drawers: quick facts
Steps29
Time1–1.5 hours
People1
ToolsPhillips screwdriver, Hammer, Drill with Ø 8 mm bit, Spirit level, Wall screws and plugs (not included)
Size70×35×35 cm (27 1/2×13 3/4×13 3/4")
Official manualAA-2345060-3
IKEA article number003.339.47 (white)
Pieces in the box78

In the box

PartPart numberQuantity
Top / bottom panel with pegs2
Side panel with keyhole slots2
Back panel1
Drawer front2
Drawer side4
Drawer bottom2
Drawer back2
Runner100959052
Runner100959062
Screw1003498
Back-panel clip100930818
Clip pin100930828
Wall spacer fitting1414132
Spacer knob1414142
Wall washer1526512
Cover cap1526502
Pin1105198
Locking device1201622
Locking device1201612
Screw1090498
Push-opener rod half100959164
Rod connector100721702
Planning sheet AA-19087851

Steps

  1. Sort the four panels — Lay the 4 panels flat on a rug, inner side up. The 2 long panels have small pegs at both ends (top and bottom; the top is marked “1”). The 2 square panels have keyhole slots: they are the sides. Check: Work on a soft surface so the mitred edges do not get chipped.
  2. Runners on the left side panel — Lay 2 runners (10095905) on one side panel, flange flat on the panel, one near the lower edge and one just above the middle. Screw each one on with 2 screws (100349), one at each end.
  3. Runners on the right side panel — Screw the 2 other runners (10095906) onto the second side panel in the same way, 2 screws (100349) each. Check: The runners are made for one side: 10095905 for the left, 10095906 for the right.
  4. Hook the “1” panel onto the left side — Stand the left side panel on its front edge, runners facing in. Hold the “1” panel at a right angle to its end, push its pegs into the wide part of the keyhole slots, then press it down until it locks. Check: The “1” and the grooves for the back panel are on the upper edges.
  5. Hook on the right side — Hook the right side panel onto the other end of the “1” panel in the same way: its keyhole slots over the pegs, then press down.
  6. Slide in the back panel — Slide the back panel into the grooves of the side panels from the open end, all the way into the groove of the “1” panel. Check: The back panel must run inside the grooves, not on top of them.
  7. Close the frame and tip it up — Hook the bottom panel onto the open end so its pegs go into both side panels at once, and press it down. Then tip the cabinet up so it stands on the bottom panel.
  8. Push the back panel down — From the back, with the “1” at the top, push the back panel down until its lower edge drops into the groove of the bottom panel. Check: Check that the back panel sits in the groove and not on its edge.
  9. Clip the back panel — Push a clip (10093081) into each of the 8 holes behind the back panel: 3 along the top, 3 along the bottom and 1 on each side. Press a pin (10093082) into each clip with your thumb so it locks.
  10. Legs or wall mounting: separate manuals — On legs (shown here): fit the legs as their own manual shows, then go on with step 11. To hang it on the wall instead, use the EKET suspension rail, sold separately with its own manual, and the planning sheet (AA-1908785). Check: Legs and the suspension rail are separate products and are not in this box.
  11. Wall spacer fittings at the top corners — From the back, press a wall spacer fitting (141413) into the two holes near the top of each side panel, behind the back panel, with the threaded drum towards the middle.
  12. Drill through the fittings — Drill through the marked centre of each spacer fitting and the back panel with an 8 mm bit. With stacked EKET cabinets, only the top cabinet needs these holes.
  13. Screw on the knobs — If there is a skirting board, screw a knob (141414) onto each spacer fitting, clockwise, all the way in. Without a skirting board, leave the knobs off, push the cabinet straight against the wall and go on to step 15. Check: Screw the knob on straight and fully, not at an angle.
  14. Turn the knobs out — Before you push the cabinet against the wall, turn both knobs anticlockwise so they stand out from the back by about the thickness of the skirting board.
  15. Push it against the wall — Push the cabinet back until the back legs touch the skirting board and both knobs rest against the wall, so the cabinet stands straight. Turn a knob a little further in or out if it does not touch. Check: Check with a spirit level and level the legs as their manual shows (manual page 19).
  16. Screw it to the wall from inside — From inside, put a washer (152651) over each drilled hole, the right way round as drawn, and screw through it into the wall. Check: Fix the cabinet to the wall to stop it tipping over. Wall screws and plugs are not included: choose ones that suit your wall.
  17. Cover caps — Press a cover cap (152650) onto each washer and turn it to lock it in place.
  18. Drawer: hook the sides onto the front — Do steps 17 to 21 for each drawer. Stand the drawer front on its bottom edge, inner side towards you. Put the pegs of each side into the keyhole slots at its ends, with the grooves of the sides and the front at the bottom.
  19. Press the sides down — Press both sides down so the pegs slide to the bottom of the keyhole slots and lock.
  20. Slide in the drawer bottom — Stand the drawer on its front. Slide the drawer bottom down the grooves of the sides until it sits in the groove of the front.
  21. Drawer back and pins — Lower the drawer back onto the ends of the sides, its rebate over the drawer bottom. Tap 2 pins (110519) through the back into each side with a hammer.
  22. Locking devices — Under the drawer bottom, at each front corner, screw a locking device to the inside of the front with 2 screws (109049): 120162 on one side and 120161 on the other, as drawn.
  23. Build the second drawer — Build the second drawer the same way (steps 17 to 21): sides onto the front and pressed down, bottom slid in, back with 4 pins, then the 2 locking devices with 2 screws each.
  24. Pull out the runners — Pull the moving part of all 4 runners out towards you.
  25. Join the push-opener rods — Push 2 rod halves (10095916) into a connector (10072170) from both ends until they meet in the middle of it. Make the second rod the same way. Check: The rod ends must touch inside the connector, with no gap.
  26. Click the rods into the runners — Hold each rod level behind the runners, at the back of the cabinet, and press it down into the clips of both runner units until it clicks. Do the upper rod and the lower rod. Check: Check that each rod is fully clicked into both clips.
  27. Put in the lower drawer — Pull the 2 runners of the lower opening all the way out. Lay the drawer on them so the hooks at their back ends go into the holes in the drawer back. Press the front down until the locking devices click, then push the drawer in.
  28. Put in the upper drawer — Pull the upper runners all the way out, lay the second drawer on them in the same way, press the front down until it clicks and push it in. Check: To open a drawer, push on its front. Lift the levers of the locking devices to take a drawer out; the fronts can be adjusted at the locking devices (manual pages 29-31).
  29. Done! — Your EKET cabinet with 2 drawers is assembled and fixed to the wall. Push a drawer front to open it. Max load: 3 kg per drawer.

EKET cabinet with 2 drawers: questions and answers

How long does it take to assemble the IKEA EKET cabinet with 2 drawers?

About 1–1.5 hours for 1 person, working through the 29 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the EKET cabinet with 2 drawers?

Phillips screwdriver, hammer, drill with Ø 8 mm bit, spirit level, wall screws and plugs (not included).

Can one person assemble the EKET cabinet with 2 drawers?

Yes, it is a one-person build.

Does the EKET cabinet with 2 drawers need to be fixed to the wall?

The manual shows a wall fixing: see step 10 (Legs or wall mounting: separate manuals) and step 11 (Wall spacer fittings at the top corners). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the EKET cabinet with 2 drawers once assembled?

70×35×35 cm (27 1/2×13 3/4×13 3/4"), as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the EKET cabinet with 2 drawers?

63 fittings of 16 kinds, the most numerous being 8 × screw, 8 × back-panel clip, 8 × clip pin. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA EKET cabinet with 2 drawers assembly instructions PDF?

The official PDF is manual AA-2345060-3, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 003.339.47 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2345060-3. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example runner 10095905). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA EKET assembly guides · All dressers & drawers assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained