IKEA EKET cabinet with 2 doors and 1 shelf assembly instructions
How to assemble the IKEA EKET cabinet with 2 doors and 1 shelf, step by step: 25 animated steps built from the official manual, about 1–1.5 hours for 1 person, with Phillips screwdriver, drill with Ø 8 mm bit, spirit level, wall screws and plugs (not included).
Dark grey EKET cabinet: four mitred panels that hook together without screws, a folding back panel held by clips, push-to-open doors on pivot pins and one shelf. Size: 70×35×70 cm (27 1/2×13 3/4×27 1/2"). About 1–1.5 hours, 1 person. Tools: Phillips screwdriver, Drill with Ø 8 mm bit, Spirit level, Wall screws and plugs (not included).
Based on the official IKEA manual AA-1914760-9 (PDF). Guide updated .
| Steps | 25 |
|---|---|
| Time | 1–1.5 hours |
| People | 1 |
| Tools | Phillips screwdriver, Drill with Ø 8 mm bit, Spirit level, Wall screws and plugs (not included) |
| Size | 70×35×70 cm (27 1/2×13 3/4×27 1/2") |
| Official manual | AA-1914760-9 |
| IKEA article number | 203.449.21 (dark grey) |
| Pieces in the box | 70 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Side panel with pegs | 2 | |
| Top / bottom panel with keyhole slots | 2 | |
| Folding back panel | 1 | |
| Shelf | 1 | |
| Door | 2 | |
| Back-panel clip | 10093081 | 12 |
| Clip pin | 10093082 | 12 |
| Screw | 108444 | 6 |
| Washer | 101313 | 2 |
| Push-opener housing 139468/155198 | 2 | |
| Push-opener plunger 139467/155197 | 2 | |
| Wall spacer fitting | 141413 | 2 |
| Spacer knob | 141414 | 2 |
| Wall washer | 152651 | 2 |
| Cover cap | 152650 | 2 |
| Shelf support | 131372 | 4 |
| Bushing | 10119600 | 4 |
| Hinge arm 10119658/10119673 | 4 | |
| Spring door pin 139477/155200 (top) | 2 | |
| Door pin 133127/155201 (bottom) | 2 | |
| Pads 152470/155675 (sheet of 2) | 1 | |
| Planning sheet AA-1908823 | 1 |
Steps
- Sort the four panels — Lay the 4 panels flat on a rug, inner side up. Two have small pegs at both mitred ends (they become the sides; one is marked “1”) and two have keyhole slots (top and bottom). The panel with the small screw holes in the middle of the front edge is the top. Check: Work on a soft surface so the mitred edges do not get chipped.
- Fit the two push-openers — On the top panel, screw a push-opener housing (139468) over each pair of holes near the front edge with 2 screws (108444). Then push a plunger (139467) into the round end of each housing until it clicks. Check: Hold the housing by its body, not by the open cradle, while you press the plunger in.
- Hook the “1” panel onto the top panel — Stand the top panel on its front edge, push-openers facing you. Hold the panel marked “1” at a right angle to its end, push its pegs into the wide part of the keyhole slots and press it down until it locks. Press the corner together. Check: The “1” and the grooves for the back panel are at the top edge, facing up.
- Hook on the bottom panel — Hook the second keyhole panel onto the other end of the “1” panel in the same way: pegs into the slots, then press down.
- Slide in the back panel — Open out the folded back panel. Slide it into the grooves from the open end, all the way into the groove of the “1” panel. Check: The back panel must run inside the grooves, not on top of them.
- Close the frame and tip it up — Hook the last peg panel onto the open end so its pegs go into both keyhole panels at once, and press it down. Then tip the box up so it stands on this panel, back facing you.
- Push the back panel down — With the “1” at the top, push the back panel down until its lower edge drops into the groove of the panel the box stands on. Check: Check that the back panel sits in the groove and not on its edge.
- First clip — Push a clip (10093081) into the hole in the middle of the lower edge, behind the back panel. Press a pin (10093082) into the clip with your thumb so it locks.
- Clip the back panel all round — Fit the other 11 clips the same way, 3 along each edge of the back panel, and press a pin into each one.
- Turn it upright, legs: separate manual — Turn the cabinet a quarter turn so the panel with the push-openers is at the top (the manual shows this turn at step 11). Then fit the legs as their own manual shows (shown here), or hang the cabinet on the EKET suspension rail with its own manual. Check: Legs and the suspension rail are separate products and are not in this box.
- Wall spacer fittings at the top corners — From the back, press a wall spacer fitting (141413) into the two holes near the top of each side panel, behind the back panel, with the threaded drum towards the middle.
- Drill through the fittings — Drill through the marked centre of each spacer fitting and the back panel with an 8 mm bit. With stacked EKET cabinets, only the top cabinet needs these holes.
- Screw on the knobs — If there is a skirting board, screw a knob (141414) onto each spacer fitting, clockwise, all the way in. Without a skirting board, leave the knobs off, push the cabinet straight against the wall and go on to step 15. Check: Screw the knob on straight and fully, not at an angle.
- Against the wall, knobs out to the wall — Turn the cabinet round and push it back until the back legs touch the skirting board. Turn both knobs anticlockwise until they rest against the wall, so the cabinet stands straight. Check: Check with a spirit level; level the legs as their manual shows. To hang the cabinet on the wall instead, use the EKET suspension rail and the planning sheet (AA-1908823) as its manual shows.
- Screw it to the wall from inside — From inside, put a washer (152651) over each drilled hole, the right way round as drawn, and screw through it into the wall. Check: Fix the cabinet to the wall to stop it tipping over. Wall screws and plugs are not included: choose ones that suit your wall.
- Cover caps — Press a cover cap (152650) onto each washer and turn it to lock it in place.
- Shelf supports — Push 4 shelf supports (131372) into the middle holes of the front and back rows, at the same height on both sides.
- Put in the shelf — Lower the shelf onto the supports so their pegs go into the holes under the shelf. Check: The front edge of the shelf must not stick out past the front of the cabinet.
- Bushings and hinge arms — Press a bushing (10119600) into the hole at each front corner: up into the top panel and down into the bottom panel. Push a hinge arm (10119658) into each bushing, arm reaching out towards the side.
- Washer on each door — Lay the doors flat, inner side up. In the small hole at the top corner of the free edge, screw a screw (108444) through a washer (101313).
- Pads — Stick a pad (152470) into the round recess at the bottom corner of the free edge of each door.
- Door pins — Stand each door up. Push a spring pin (139477) into the hole in the top edge on the hinge side, and a plain pin (133127) into the hole in the bottom edge. Check: The spring pin, with the ribbed window, always goes at the top.
- Bottom pins into the lower arms — Hold each door a little open with its top tilted out, and put the bottom pin into the hole of the lower hinge arm.
- Click the top pins into the upper arms — Press the spring pin at the top of the door down, swing the top of the door in under the upper hinge arm and let go: the pin clicks up into the arm. Then push both doors shut until the push-openers catch them. Check: To open a door, push on it near the top of its free edge. Turn the hinge arms to line the doors up, and screw the plungers in or out to adjust the gap (manual pages 27-28).
- Done! — Your EKET cabinet is assembled and fixed to the wall. Max load on the shelf: 10 kg. Push a door near its free edge to open it.
EKET cabinet with 2 doors and 1 shelf: questions and answers
How long does it take to assemble the IKEA EKET cabinet with 2 doors and 1 shelf?
About 1–1.5 hours for 1 person, working through the 25 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the EKET cabinet with 2 doors and 1 shelf?
Phillips screwdriver, drill with Ø 8 mm bit, spirit level, wall screws and plugs (not included).
Can one person assemble the EKET cabinet with 2 doors and 1 shelf?
Yes, it is a one-person build.
Does the EKET cabinet with 2 doors and 1 shelf need to be fixed to the wall?
The manual shows a wall fixing: see step 11 (Wall spacer fittings at the top corners) and step 25 (Done). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.
What size is the EKET cabinet with 2 doors and 1 shelf once assembled?
70×35×70 cm (27 1/2×13 3/4×27 1/2"), as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the EKET cabinet with 2 doors and 1 shelf?
57 fittings of 14 kinds, the most numerous being 12 × back-panel clip, 12 × clip pin, 6 × screw. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA EKET cabinet with 2 doors and 1 shelf assembly instructions PDF?
The official PDF is manual AA-1914760-9, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 203.449.21 (dark grey); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-1914760-9. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example back-panel clip 10093081). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA EKET cabinet assembly instructions
- IKEA EKET cabinet with 4 compartments assembly instructions
- IKEA EKET cabinet with 2 drawers assembly instructions
- IKEA BILLY bookcase assembly instructions
- IKEA KALLAX shelf unit 2x4 assembly instructions
- IKEA BESTÅ frame assembly instructions
- IKEA HYLLIS shelving unit (in/outdoor) assembly instructions
- IKEA LACK wall shelf assembly instructions
All IKEA EKET assembly guides · All bookcases & shelves assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained