Step by StepAssembly Find your furniture

IKEA KALLAX shelf unit 2x4 assembly instructions

How to assemble the IKEA KALLAX shelf unit 2x4, step by step: 20 animated steps built from the official manual, about 45–60 min for 2 people, with hex key 100001 (included), hammer, Phillips screwdriver, flat screwdriver, pencil, spirit level.

IKEA KALLAX shelf unit 2x4, assembled

The classic 8-cube shelf unit: a screwed frame around a dowelled grid of shelves and dividers, fixed to the wall. Size: 77×39×147 cm (30 1/8×15 3/8×57 5/8"). About 45–60 min, 2 people. Tools: Hex key 100001 (included), Hammer, Phillips screwdriver, Flat screwdriver, Pencil, Spirit level.

Based on the official IKEA manual AA-2703433-1 (PDF). Guide updated .

KALLAX shelf unit 2x4: quick facts
Steps20
Time45–60 min
People2
ToolsHex key 100001 (included), Hammer, Phillips screwdriver, Flat screwdriver, Pencil, Spirit level
Size77×39×147 cm (30 1/8×15 3/8×57 5/8")
Official manualAA-2703433-1
IKEA article number206.316.63 (white)
Pieces in the box54

In the box

PartPart numberQuantity
Side panel (long)2
Top/bottom panel2
Shelf (full width)3
Divider (short)4
Screw 104321/1043228
Wooden dowel10133922
Hex key1000011
Felt pad sheet 10002300/100503342
Wall bracket1157532
Screw1003724
Keyhole plate1036932
Bracket cover1157542

Steps

  1. Screw the bottom panel to a side panel — Work on a soft surface. Stand one long side panel and one short end panel (the bottom) on their long edges at a right angle. Screw 2 screws through the end panel into the end of the side panel with the hex key. Check: Use the countersunk holes (the ones with a wide rim) on the outside of the end panel.
  2. First divider with 2 dowels — Tap 2 dowels into the middle holes on the inside of the bottom panel with a hammer. Push a small divider onto them.
  3. First shelf — Push 2 dowels into the side panel, next to the first divider. Slide a long shelf onto them, so it closes off the first divider.
  4. 2 dowels into the first shelf — Push 2 dowels into the two middle holes on the other face of the first shelf.
  5. Second divider — Slide the second divider onto the 2 dowels.
  6. Second shelf — Push 2 dowels into the side panel next to the second divider and slide the second shelf onto them.
  7. 2 dowels into the second shelf — Push 2 dowels into the middle holes of the second shelf.
  8. Third divider — Slide the third divider onto the dowels.
  9. Third shelf — Fit the third shelf the same way: 2 dowels into the side panel, then slide the shelf onto them.
  10. 2 dowels into the third shelf — Push 2 dowels into the middle holes of the third shelf.
  11. Fourth divider — Slide the last divider onto the dowels.
  12. 8 dowels into the free ends — Push 2 dowels into the free end of each shelf and 2 into the free end of the last divider.
  13. Second side panel — Turn the second side panel so its holes face the shelves, as shown, and press it onto the dowels of all three shelves. It lines up with the bottom panel.
  14. Top panel and 6 screws — Tip the last end panel (the top) up onto the 2 dowels of the last divider. Then screw the frame together with 6 screws: 2 through the bottom panel into the new side panel and 4 through the top panel.
  15. Felt pads under the bottom — This guide follows the upright 2x4 setup. Peel 4 felt pads off one sheet and stick them to the corners of the bottom panel’s outside face. Check: Placing it on its long side instead (4x2)? The manual continues on page 31: then 8 pads go under the long side.
  16. Stand it up and fit the wall brackets — Stand the unit up on its bottom panel, close to where it will go. In the top cube of each column, screw a wall bracket to the inside of the side panel, in the back corner and flush with the back edge, with 2 screws. Check: Tip-over danger: this unit must be fixed to the wall. Never leave it standing upright without the wall fixing.
  17. Check it is upright and mark the wall — Place the unit against the wall where it will stand. Check it is straight with a spirit level, then mark the wall with a pencil through the big hole of both brackets.
  18. Screws into the wall — Move the unit away. Drill at the 2 marks and put in screws (and plugs) suited to your wall. Leave the screw heads sticking out about 5 mm. Check: Wall screws and plugs are not included: choose ones made for your wall material. Do not drive the screws all the way in.
  19. Hook on and lock to the wall — Slide the unit back so the screw heads come through the brackets. Put a keyhole plate over each screw head, adjust it and tighten the screw. Finish by pushing a cover onto each bracket.
  20. Done! — Your KALLAX shelf unit is assembled and fixed to the wall. Max load: 13 kg (29 lb) per cube.

KALLAX shelf unit 2x4: questions and answers

How long does it take to assemble the IKEA KALLAX shelf unit 2x4?

About 45–60 min for 2 people, working through the 20 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the KALLAX shelf unit 2x4?

Hex key 100001 (included), hammer, Phillips screwdriver, flat screwdriver, pencil, spirit level. Already in the box: Hex key 100001.

Can one person assemble the KALLAX shelf unit 2x4?

It is planned as a 2-person build. One person can do most of it, but get help for step 16, where the furniture is lifted or turned.

Does the KALLAX shelf unit 2x4 need to be fixed to the wall?

The manual shows a wall fixing: see step 16 (Stand it up and fit the wall brackets) and step 17 (Check it is upright and mark the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the KALLAX shelf unit 2x4 once assembled?

77×39×147 cm (30 1/8×15 3/8×57 5/8"), as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the KALLAX shelf unit 2x4?

43 fittings of 8 kinds, the most numerous being 22 × wooden dowel, 8 × screw 104321/104322, 4 × screw. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA KALLAX shelf unit 2x4 assembly instructions PDF?

The official PDF is manual AA-2703433-1, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 206.316.63 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2703433-1. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example screw 104321). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA KALLAX assembly guides · All bookcases & shelves assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained