IKEA KALLAX desk assembly instructions
How to assemble the IKEA KALLAX desk, step by step: 22 animated steps built from the official manual, about 1–1.5 hours for 1 person, with hex key 100092 (included), flat screwdriver, Phillips screwdriver, hammer.
Shallow desk with a built-in 1×2 KALLAX shelf section, one leg panel and a hidden cable tray under the desktop. Size: 111×39 cm, height 77 cm. About 1–1.5 hours, 1 person. Tools: Hex key 100092 (included), Flat screwdriver, Phillips screwdriver, Hammer.
Based on the official IKEA manual AA-2713546-1 (PDF). Guide updated .
| Steps | 22 |
|---|---|
| Time | 1–1.5 hours |
| People | 1 |
| Tools | Hex key 100092 (included), Flat screwdriver, Phillips screwdriver, Hammer |
| Size | 111×39 cm, height 77 cm |
| Official manual | AA-2713546-1 |
| IKEA article number | 305.824.45 (white) |
| Pieces in the box | 78 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Desktop | 1 | |
| Leg panel | 1 | |
| Shelf section side | 2 | |
| Shelf section bottom | 1 | |
| Middle shelf | 1 | |
| Cable tray back panel | 1 | |
| Cable tray bottom | 1 | |
| Cable tray front rail | 1 | |
| Cam screw | 114613 | 18 |
| Wooden dowel | 101372 | 12 |
| Cam lock | 102509 | 12 |
| Cam lock | 114926 | 6 |
| Screw | 104321 | 4 |
| Glide | 157409 | 6 |
| Plug 124257/124258/10102369 | 8 | |
| Plug 10213618/10070195/10047130/10214857 | 2 | |
| Hex key | 100092 | 1 |
Steps
- Cam screws into the two sides — Lay the two side panels of the shelf section flat on a soft surface, the faces with the two middle holes up. Screw 2 cam screws into the middle holes of each panel.
- Sides onto the middle shelf — Stand the middle shelf on its back edge. Tip each side panel up onto its back edge and push its cam screws into the holes in the shelf ends. The side with the row of small holes goes on the left, holes facing out (towards the knee space). Check: Building the shelf section on the left instead? Follow the mirrored pages 9-12 and 26-35 of the manual.
- Lock the shelf — Press 4 cam locks 102509 (the small ones, not 114926) into the big holes on the shelf, the arrows pointing to the cam screws. Turn each one clockwise with a flat screwdriver until it locks.
- Bottom panel — Fit the bottom panel across the ends of both sides. Drive 4 long screws 104321 through it into the sides with the hex key.
- Cam screws for the cable tray — On the outside face of the side with the small holes, screw 4 cam screws into the holes near the top end: 3 in a row by the back edge and 1 a little further in.
- Dowels into the tray bottom — Lay the narrow tray bottom flat. Tap 2 dowels into each long edge with a hammer (4 in total).
- Tray bottom onto the back panel — Lay the wide tray back panel flat. Stand the tray bottom on its edge and press its dowels into the holes along the middle of the back panel.
- Dowels into the front rail — Tap 1 dowel into each end of the front rail with a hammer.
- Front rail onto the tray bottom — Press the front rail down onto the 2 dowels in the top edge of the tray bottom, its big holes facing up.
- Tray onto the shelf section — Slide the cable tray onto the 4 cam screws in the side of the shelf section, back panel down on the floor, until it sits flat against the side.
- Cam screws into the leg — Lay the leg panel flat, the face with the holes up. Screw 4 cam screws into the holes near its top end, the same way as on the shelf section.
- Leg onto the tray — Tip the leg up onto its back edge and push its cam screws into the free end of the cable tray.
- Lock the front rail — Press a cam lock 102509 into the big hole at each end of the front rail and turn it clockwise with a flat screwdriver.
- Glides — Peel the backing off the glides. Stick 4 near the corners of the shelf section bottom and 2 on the bottom edge of the leg.
- Stand it up and lock the tray — Stand the desk frame up on its glides. From behind, press 6 cam locks 102509 into the big holes at the ends of the tray back panel (3 at each end) and turn each clockwise.
- Dowels into the top edges — Push 2 dowels into the top edge of the leg and of each shelf section side (6 in total).
- Cam screws into the desktop — Lay the desktop upside down on a soft surface. Screw 6 cam screws into the holes in its underside: 2 at each end and 2 a third of the way in.
- Desktop on — Turn the desktop over and lower it onto the frame, so its cam screws and the dowels in the panel tops go into each other’s holes.
- Lock the desktop — Press 6 large cam locks 114926 into the big holes just under the desktop: 2 in the knee side of the leg and 2 inside each side of the top cube. Turn each clockwise with a flat screwdriver.
- Plugs — Press 8 small plugs 124257 into the unused holes near the front of the leg and of the shelf section side, 4 on each: the column of 3 and the lower hole of the pair. Leave the upper hole of each pair open.
- Last two plugs — Press the 2 larger plugs 10213618 into the holes left open in step 20.
- Done! — Your KALLAX desk is ready. Max load 50 kg on the desktop (15 kg on a small area) and 8 kg per shelf. Re-tighten the cam locks after about two weeks.
KALLAX desk: questions and answers
How long does it take to assemble the IKEA KALLAX desk?
About 1–1.5 hours for 1 person, working through the 22 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the KALLAX desk?
Hex key 100092 (included), flat screwdriver, Phillips screwdriver, hammer. Already in the box: Hex key 100092.
Can one person assemble the KALLAX desk?
Yes, it is a one-person build.
What size is the KALLAX desk once assembled?
111×39 cm, height 77 cm, as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the KALLAX desk?
69 fittings of 9 kinds, the most numerous being 18 × cam screw, 12 × wooden dowel, 12 × cam lock. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA KALLAX desk assembly instructions PDF?
The official PDF is manual AA-2713546-1, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 305.824.45 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2713546-1. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example cam screw 114613). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA KALLAX shelf unit 2x4 assembly instructions
- IKEA MICKE desk assembly instructions
- IKEA ALEX desk assembly instructions
- IKEA ÖRFJÄLL children's desk chair assembly instructions
All IKEA KALLAX assembly guides · All desks assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained