IKEA ALEX desk assembly instructions
How to assemble the IKEA ALEX desk, step by step: 30 animated steps built from the official manual, about 1.5–2.5 hours for 1 person, with flat & Phillips screwdriver, hammer, Allen key (included).
White desk with two wide drawers under the desktop, a hinged flap over a hidden cable compartment with two cable outlets, on slim white steel legs. Size: 132x58 cm (52x22 7/8"). About 1.5–2.5 hours, 1 person. Tools: Flat & Phillips screwdriver, Hammer, Allen key (included).
Based on the official IKEA manual AA-2241985-3 (PDF). Guide updated .
| Steps | 30 |
|---|---|
| Time | 1.5–2.5 hours |
| People | 1 |
| Tools | Flat & Phillips screwdriver, Hammer, Allen key (included) |
| Size | 132x58 cm (52x22 7/8") |
| Official manual | AA-2241985-3 |
| IKEA article number | 804.834.38 (white) |
| Pieces in the box | 102 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Desktop | 1 | |
| Bottom panel (with 2 cable holes) | 1 | |
| Side panel | 2 | |
| Divider | 1 | |
| Back rail | 1 | |
| Drawer-bay back wall | 2 | |
| Flap | 1 | |
| Drawer: front, 2 sides with runners, bottom, back | 2 | |
| Leg frame: top ring, 2 leg frames, rear stretcher | 1 | |
| Runner | 127101 | 4 |
| Cam screw | 118331 | 4 |
| Cam screw | 100481 | 6 |
| Cam lock | 103114 | 4 |
| Cam lock | 119251 | 6 |
| Wooden dowel | 101345 | 26 |
| Pin | 110519 | 8 |
| Screw | 110853 | 8 |
| Screw | 100218 | 8 |
| Screw | 109534 | 4 |
| Screw | 105021 | 4 |
| Hinge mounting plate | 124639 | 2 |
| Hinge | 122166 | 2 |
| Cable outlet | 123603 | 2 |
| Allen key | 100001 | 1 |
| Adjusting tool | 106699 | 1 |
Steps
- Cam screws in the drawer fronts — Both drawers are built the same way. Lay each drawer front face down on the rug, finger grip towards you, and screw a cam screw 118331 into the small hole near each end of the inside face. Check: Use the cam screws 118331 here, not the shorter 100481. Work on a rug or the cardboard.
- Dowels and drawer sides — Push a wooden dowel into the hole in the end of each drawer side. Stand the sides on the ends of the front, groove facing in and the runner strip along the edge away from the finger grip, so the dowel and the cam screw go into the holes.
- Lock the drawer sides — Insert a cam lock 103114 into the large hole near the front of each drawer side and turn it clockwise with a flat screwdriver until it grips the cam screw. Check: Use the cam locks with the cross (103114) for the drawers, not 119251.
- Slide in the drawer bottoms — Slide a drawer bottom down into the grooves of each drawer, all the way to the front.
- Drawer backs and pins — Lower the drawer back between the ends of the sides so it rests on the drawer bottom. Tap 2 pins 110519 through each side into the end of the back with a hammer: 4 per drawer.
- Cam screws in the desktop — Put the drawers aside. Lay the desktop face down on the rug and screw the 6 cam screws 100481 into its small holes: 2 near each end and 2 in the middle for the divider. Check: Use the cam screws 100481 here, not 118331.
- Runner on the divider — Take the divider and lay it flat. Place a runner 127101 on it, slide the inner part of the runner aside to reach the holes, and fix it with 2 screws 110853. Check: Check the holes: the divider is the shorter board with no holes in its ends.
- Turn over: second runner — Turn the divider over and fix the second runner on the other face in the same way, with 2 screws 110853.
- Divider onto the desktop — Push 2 dowels into the long edge of the divider. Stand the divider upright across the middle of the desktop so the dowels and the 2 middle cam screws go into its holes.
- Lock the divider — Insert 2 cam locks 119251 into the large holes in the divider and turn them clockwise to lock onto the cam screws. Check: Use the plain cam locks 119251 here, not the ones with a cross.
- Runners on the side panels — Lay both side panels flat, inside face up, and fix a runner 127101 to each with 2 screws 110853.
- Hinge plates on the back rail — Lay the back rail flat with its drilled face up. Press the 2 hinge mounting plates 124639 into their holes and tighten the 2 screws already fitted in each plate.
- Side panels onto the back rail — Stand the back rail on its long edge, plates facing you. Push 2 dowels into each end, then press the side panels onto the ends, runners facing in.
- Frame onto the desktop — Push 4 dowels into the holes near the ends of the desktop. Lift the back rail and side panels together onto the desktop so the dowels and end cam screws go into the side panels. The divider sits between them.
- Lock the side panels — Insert the 4 cam locks 119251 into the inside faces of the side panels and turn each one clockwise to lock.
- Dowels in the top edges — Push 8 dowels into the holes in the edges facing up: 2 in the back rail, 2 in each side panel and 2 in the divider.
- Bottom panel — Lay the bottom panel on top, cable holes at the back, so the dowels go into its holes. Fix it to the divider with 1 long screw 100218 and the Allen key. Check: The two round cable holes go at the back, over the narrow compartment behind the drawers.
- Leg frame: legs into the top ring — Lay the top ring of the leg frame on the floor. Lower the two leg frames into it, legs pointing up, so the tabs at the ends of the legs go into the slots in the ring.
- Lock the leg frames — Press each leg frame down into the ring and slide it along until the tabs lock in the slots.
- Rear stretcher — Clip the rear stretcher between the two legs on the back side, level with the crossbars, so it snaps into the holes in the legs. Check: Check the drawing on page 14: the open side of the stretcher faces into the frame.
- Leg frame onto the desk — Turn the leg frame round and set it, legs up, on the bottom panel of the desk, lined up with its edges.
- Screw the leg frame on — Fix the top ring to the bottom panel with 7 long screws 100218 and the Allen key: 3 along the back and 2 at each end.
- Turn the desk over, cable outlets — With a helper, turn the desk over onto its legs. Press the 2 cable outlets 123603 into the round holes in the bottom panel, through the opening behind the desktop. Check: Get a helper to turn the desk over.
- Dowels in the back walls — Lay the 2 back walls for the drawer bays flat and push 2 dowels into one long edge of each.
- Back walls behind the drawer bays — Lower each back wall, dowels down, into the opening behind the desktop, close against the desktop edge, and press it down so the dowels go into the holes in the bottom panel.
- Hinges on the flap — Lay the flap face down, finger notch towards you. Press the 2 hinges 122166 into the round holes near the straight back edge and fix each with 2 screws 109534.
- Hang the flap — Hold the flap up over the opening at the back, hinges down. Hook each hinge arm onto its plate on the back rail and press until it clicks, then close the flap. Check: If the flap does not sit level, adjust it sideways, up/down or in/out with the screws on the hinge arms, using the tool 106699 (manual page 19).
- First drawer onto its runners — Pull the inner parts of the two left-hand runners out towards you. Set the drawer’s runners onto them, fix the drawer with 1 screw 105021 through each runner, then push the drawer in.
- Second drawer — Fit the second drawer in the right-hand bay the same way: runners out, drawer on, 1 screw 105021 through each runner, push it in.
- Done! — Your ALEX desk is ready. Max load: 50 kg on the desktop and 3 kg per drawer. Lift the flap at the back to reach the cable compartment and the two cable outlets.
ALEX desk: questions and answers
How long does it take to assemble the IKEA ALEX desk?
About 1.5–2.5 hours for 1 person, working through the 30 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the ALEX desk?
Flat & Phillips screwdriver, hammer, Allen key (included). Already in the box: Allen key.
Can one person assemble the ALEX desk?
Yes, it is a one-person build.
What size is the ALEX desk once assembled?
132x58 cm (52x22 7/8"), as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the ALEX desk?
88 fittings of 14 kinds, the most numerous being 26 × wooden dowel, 8 × pin, 8 × screw. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA ALEX desk assembly instructions PDF?
The official PDF is manual AA-2241985-3, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 804.834.38 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2241985-3. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example runner 127101). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA ALEX drawer unit assembly instructions
- IKEA ALEX drawer unit on castors assembly instructions
- IKEA ALEX drawer unit with 9 drawers assembly instructions
- IKEA MICKE desk assembly instructions
- IKEA KALLAX desk assembly instructions
- IKEA ÖRFJÄLL children's desk chair assembly instructions
All IKEA ALEX assembly guides · All desks assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained