Step by StepAssembly Find your furniture

IKEA MICKE desk assembly instructions

How to assemble the IKEA MICKE desk, step by step: 36 animated steps built from the official manual, about 2–3 hours for 1 person, with flat & Phillips screwdriver, hammer.

IKEA MICKE desk, assembled

Compact desk with a cabinet, a wide drawer, a small drawer, a cable outlet and a hidden cable tray at the back. Size: 105×50 cm (41 3/8×19 5/8"). About 2–3 hours, 1 person. Tools: Flat & Phillips screwdriver, Hammer.

Based on the official IKEA manual AA-476615-12 (PDF). Guide updated .

MICKE desk: quick facts
Steps36
Time2–3 hours
People1
ToolsFlat & Phillips screwdriver, Hammer
Size105×50 cm (41 3/8×19 5/8")
Official manualAA-476615-12
IKEA article number802.130.74 (white)
Pieces in the box134

In the box

PartPart numberQuantity
Desktop1
Cabinet side panel2
Drawer panel above the leg1
Cabinet bottom1
Cabinet back rail1
Cable tray rail, bottom and lip3
Door1
Shelf2
Leg frame1541931
Wide drawer (front, 2 sides, bottom, back)1
Small drawer (front, 2 sides, bottom, back)1
Drawer runner set1124822
Bolt1000863
Pin1105194
Cam screw11833122
Cam lock11012610
Cam lock1034308
Cam lock1031144
Screw10036520
Screw1132874
Shelf pin1015148
Wooden dowel10134420
Bumpers 104663 (sheet of 2)1
Glide1535494
Bumpers 130521 (sheet of 4)1
Felt pads 10081375 (sheet of 2)1
Hinge mounting plate1092212
Hinge1093382
Allen key handle1210301
Allen key1000921
Cable outlet1213041

Steps

  1. Cam screws into both drawer fronts — Both drawers (the wide one and the small one) are built the same way. Lay each drawer front on a soft surface, inside face up, and screw 2 cam screws into the holes at its ends. Check: Work on a rug or the cardboard to avoid scratches.
  2. Dowels and drawer sides — Push a wooden dowel into the lower hole at the end of each drawer side. Stand the sides on the ends of the fronts, pressing the dowels and cam screws into the holes.
  3. Lock the sides with cam locks — Insert a cam lock 103114 into the hole in the outside of each drawer side and turn it clockwise with a flat screwdriver until it grips the cam screw. Check: Use the cam lock 103114 here, not 110126 or 103430.
  4. Turn over and slide in the bottom — Turn each drawer over so it rests on the top edges. Slide the drawer bottom into the grooves, all the way to the front, with the plain white side facing into the drawer.
  5. Fit the back panel — Set the lower edge of the back panel between the open ends of the drawer sides, leaning outwards, then swing it up until the edge of the drawer bottom sits in its groove.
  6. Nail the back panel — Hammer a pin 110519 through each drawer side into the end of the back panel. Check: Support the drawer side on the floor while you hammer.
  7. Drawer runners onto the drawers — Place a drawer runner along the edge of each drawer side, with the wheel at the back end of the drawer.
  8. Screw on the runners — Fix each runner to the drawer side with 2 screws 100365. Check: Use the short screws 100365, not 113287.
  9. Cable tray: rail and tray bottom — The drawers are done; put them aside. Lay the long rear rail on the rug. Push 2 dowels into the edge of the tray bottom and press it upright onto the rail. Check: This manual builds the cabinet on the left. For the cabinet on the right, follow the mirrored steps on pages 25–39.
  10. Cable tray: front lip — Push 2 dowels into the free edge of the tray bottom and press the narrow lip on top, with its cam-lock holes facing up.
  11. Cam screws in two panels — Lay the drawer panel for above the leg and the inner cabinet side flat, inside up. Screw 4 cam screws into each, at the holes near the back edge.
  12. Runners for the wide drawer — Screw a cabinet runner onto each of the two panels with 2 screws 100365, wheel at the front edge. Check: Use the short screws 100365, not 113287.
  13. Join the panels to the cable tray — Push 2 dowels into the ends of the lip. Stand both panels up and press them onto the ends of the cable tray, cam screws into the holes.
  14. Lock the cable tray — Insert the 8 cam locks 103430 into the rail and lip, 4 at each end, and turn each one clockwise to lock. Check: Use the cam lock 103430 here, not 110126.
  15. Runners for the small drawer — Screw a runner onto the cabinet side of the inner panel, and one onto the outer cabinet side (lying flat), 2 screws 100365 each.
  16. Hinge mounting plates — Screw the 2 hinge mounting plates onto the inside of the outer cabinet side with 2 screws 113287 each. Check: Use the longer screws 113287 here, not 100365.
  17. Cam screws for the cabinet bottom — Screw 2 cam screws into the cabinet side of the inner panel and 2 into the outer cabinet side, at the bottom end.
  18. Cabinet bottom — Push the cabinet bottom onto the cam screws at the bottom end of the inner panel, white face towards the inside of the cabinet.
  19. Lock the bottom (2 cam locks) — Insert 2 cam locks 110126 into the outside of the bottom panel and turn them clockwise to lock.
  20. Cabinet back rail — Push 4 dowels into the ends of the small back rail (the unfinished edges) and fit it between the top ends of the cabinet, against the inner panel.
  21. Outer cabinet side — Lift the outer cabinet side up and press it onto the cabinet bottom and the back rail.
  22. Lock the bottom (2 more cam locks) — Insert 2 more cam locks 110126 into the bottom panel at the outer side and turn them to lock.
  23. Dowels in the top edges — Push 2 dowels into the top edge of each of the three upright panels (6 in total).
  24. Fix the leg frame — Hold the leg frame against the bottom edge of the drawer panel and fix it with 3 bolts 100086. Slide the Allen key into its handle (hole 4) for extra grip.
  25. Cam screws in the desktop — Lay the desktop upside down on the rug and screw 6 cam screws into its underside.
  26. Fit the desktop — Lift the desktop onto the top ends of the panels, cable-outlet hole at the back above the cable tray, and press it down onto the dowels and cam screws. Check: Check that the cable-outlet hole is at the back, above the cable tray.
  27. Lock the desktop — Insert 6 cam locks 110126 into the panels just below the desktop and turn them clockwise to lock.
  28. Glides under the cabinet — Press the 4 glides 153549 into the bottom edges of the two cabinet sides.
  29. Felt pads under the leg — Stick the 2 hexagonal felt pads 10081375 under the leg frame. (The round bumpers are used later.)
  30. Stand up the desk and fit the drawers — Carefully stand the desk up. Insert the drawers: rest the drawer runners on the cabinet runners, push the drawer in and lower it until the wheels drop into place. Check: Two people recommended for standing the desk up.
  31. Hinges onto the door — Lay the door face down. Press the 2 hinges into the round holes and fix each with 2 screws 100365.
  32. Hang the door — Hook each hinge onto its mounting plate on the outer cabinet side and press until it clicks, then tighten the screw on the hinge arm. Check: The door can be adjusted up/down, sideways and in/out with the hinge screws (see the last page of the manual).
  33. Shelf pins and shelves — Open the door. Push 4 shelf pins into the holes for each shelf, at the same height on both sides, and lay the 2 shelves on them.
  34. Door bumpers — Stick the 2 small bumpers 104663 inside the cabinet, on the panel the door closes against, near the front edge.
  35. Cable outlet and drawer bumpers — Close the door. Press the cable outlet into the hole in the desktop. Stick the 4 round bumpers 130521 to the front of the panels at both sides of the wide drawer opening.
  36. Done! — Your MICKE desk is assembled. Max load: 50 kg (110 lb) on the desktop, 31 kg (68 lb) in the wide drawer, 1 kg (2 lb) in the small drawer, 8 kg (18 lb) per shelf.

MICKE desk: questions and answers

How long does it take to assemble the IKEA MICKE desk?

About 2–3 hours for 1 person, working through the 36 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the MICKE desk?

Flat & Phillips screwdriver, hammer.

Can one person assemble the MICKE desk?

Yes, it is a one-person build.

What size is the MICKE desk once assembled?

105×50 cm (41 3/8×19 5/8"), as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the MICKE desk?

115 fittings of 16 kinds, the most numerous being 22 × cam screw, 20 × screw, 20 × wooden dowel. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA MICKE desk assembly instructions PDF?

The official PDF is manual AA-476615-12, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 802.130.74 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-476615-12. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example leg frame 154193). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA MICKE assembly guides · All desks assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained