Step by StepAssembly Find your furniture

IKEA MICKE drawer unit with drop-file storage assembly instructions

How to assemble the IKEA MICKE drawer unit with drop-file storage, step by step: 35 animated steps built from the official manual, about 2–3 hours for 1 person, with flat & Phillips screwdriver, hammer.

IKEA MICKE drawer unit with drop-file storage, assembled

Narrow white MICKE drawer unit on castors: three small drawers on roller runners over a deep drop-file drawer on full-extension ball-bearing runners, with its own castor under the front. Size: 35x75 cm. About 2–3 hours, 1 person. Tools: Flat & Phillips screwdriver, Hammer.

Based on the official IKEA manual AA-487829-7 (PDF). Guide updated .

MICKE drawer unit with drop-file storage: quick facts
Steps35
Time2–3 hours
People1
ToolsFlat & Phillips screwdriver, Hammer
Size35x75 cm
Official manualAA-487829-7
IKEA article number502.130.80 (white)
Pieces in the box145

In the box

PartPart numberQuantity
Side panel2
Top1
Bottom rail2
Back panel (fibreboard)1
Small drawer (front, 2 sides, bottom, back)3
Drop-file drawer (front, 2 sides, bottom, back)1
Drawer runner set1124823
Ball-bearing runner set1253171
Cam screw11833118
Wooden dowel10134418
Cam lock1101268
Cam lock10311410
Pin11051910
Screw10036524
Screw11392812
Screw1090672
Screw1095601
Stop clip100930814
Cap100930824
Castor socket1014674
Castor pin1094124
Locking castor1132542
Castor1132553
Castor bracket with pin1221631
Hook1221644
File frame1221652

Steps

  1. Cam screws in the side panels — Lay both side panels on a soft surface, inside faces up and their grooved back edges facing each other. Screw 2 cam screws 118331 into the holes at the bottom end of each panel. Check: Work on a rug or the cardboard to avoid scratches.
  2. Take apart the ball-bearing runners — Pull the inner rail out of each ball-bearing runner: slide it out, press the black lever and pull it free. Keep the 2 inner rails for the drop-file drawer (step 29).
  3. Ball-bearing runners on the sides — Lay each runner on its side panel along the bottom end, the end with the lever at the front edge. Fix each one with 3 screws 113928 in the holes shown. Check: Use the screws 113928 here, not 100365 or 109067.
  4. Drawer runners on the sides — Screw 3 drawer runners onto each side panel, wheel at the front edge, with 2 screws 100365 each: 12 screws in total. Check: Use the screws 100365 here, not 113928 or 109067.
  5. Join the sides with the bottom rails — Stand both side panels on their back edges, runners inside. Set the 2 bottom rails between them at the bottom end, push 4 dowels into the rail ends and press the sides onto the rails, cam screws into the holes. Check: Check that the cam lock holes in the rails face outwards (towards the bottom end).
  6. Lock the rails and stand it up — Insert 4 cam locks 110126 into the outside of the rails and turn each one clockwise to lock it. Then carefully stand the unit upright on the rails. Check: Use the larger cam locks 110126 here, not 103114.
  7. Slide in the back panel — Slide the back panel down into the grooves at the back of the side panels, white side facing in, until it rests on the back rail.
  8. Dowels in the side tops — Push 2 wooden dowels into the holes in the top edge of each side panel.
  9. Cam screws in the top — Lay the top upside down on the rug and screw 4 cam screws 118331 into the holes near its ends.
  10. Fit the top — Turn the top over and lower it onto the side panels, pressing the dowels and cam screws into the holes in their top edges.
  11. Lock the top — Insert 4 cam locks 110126 into the holes on the inside of the side panels, just below the top, and turn each one clockwise to lock. Check: Use the larger cam locks 110126 here, not 103114.
  12. Stop clips inside the sides — Push a stop clip 10093081 into each of the 4 holes near the back of the side panels (2 per side), then press a cap 10093082 onto each clip.
  13. Turn over, castor sockets in — Turn the unit upside down onto its top. Tap a castor socket 101467 into the hole at each end of the two rails with a hammer.
  14. Locking castors at the front — Push a castor pin 109412 into each socket on the front rail until it clicks, then press a locking castor 113254 onto each pin until it clicks.
  15. Castors at the back — Push the other 2 castor pins 109412 into the sockets on the back rail and press a castor 113255 (without a brake) onto each until it clicks.
  16. Stand the unit on its castors — Turn the unit back over so it stands on its 4 castors, open front towards you.
  17. Small drawers: cam screws in the fronts — The 3 small drawers are built the same way. Lay each drawer front face down on the rug and screw 2 cam screws 118331 into the holes at its ends. Check: Work on a rug or the cardboard to avoid scratches.
  18. Small drawers: dowels and sides — Push a wooden dowel into the end of each drawer side. Stand the 2 sides on the ends of each front, pressing the dowels and cam screws into the holes, groove for the bottom towards the bottom edge.
  19. Small drawers: lock the sides — Insert a cam lock 103114 into the hole in the outside of each drawer side and turn it clockwise until it grips the cam screw. Check: Use the small cam locks 103114 here, not 110126.
  20. Small drawers: slide in the bottoms — Turn each drawer over so it rests upside down with the front at the far end. Slide the drawer bottom into the grooves, all the way to the front.
  21. Small drawers: back and pins — Set the back panel between the open ends of the sides, leaning outwards, and swing it up over the edge of the bottom. Tap 2 pins 110519 through the sides into the back with a hammer.
  22. Small drawers: runners on — Lay a drawer runner along the bottom edge of each drawer side, wheel at the back end of the drawer.
  23. Small drawers: screw on the runners — Fix each drawer runner to the drawer side with 2 screws 100365: 4 per drawer, 12 in total. Check: Use the screws 100365 here, not 113928 or 109067.
  24. Fit the small drawers — Hold each drawer level in front of its opening, front tipped down a little, rest its back wheels on the runners in the unit and push it in until the wheels drop into place. Fit all 3 the same way.
  25. Drop-file drawer: cam screws — Lay the large drawer front face down on the rug and screw 4 cam screws 118331 into the holes near its ends.
  26. Drop-file drawer: dowels and sides — Push 2 wooden dowels into the end of each side. Stand the sides on the ends of the front, pressing the dowels and cam screws into the holes, hole pattern facing in.
  27. Drop-file drawer: lock the sides — Insert 4 cam locks 103114 into the holes in the outside of the sides and turn each one clockwise to lock.
  28. Drop-file drawer: bottom and back — Slide the drawer bottom down the grooves to the front. Set the back between the sides, swing it over the edge of the bottom and tap 4 pins 110519 through the sides into it.
  29. Castor bracket on the front — Lay the drawer upside down on a table with the front hanging over the edge. Fit the castor bracket 122163 on the lower edge of the front: 2 screws 109067 through the tab, 1 screw 109560 through the pin. Check: Use the screws 109067 here, not 113928.
  30. Castor under the front — Press the last castor 113255 onto the bracket pin until it clicks.
  31. Inner rails on the drawer — Take the 2 inner rails from step 2. Lay one along the bottom edge of each drawer side, front end against the front, and fix it with 3 screws 113928. Check: Use the screws 113928 here.
  32. Turn over, hooks in — Turn the drawer the right way up. Screw the 4 hooks 122164 by hand into the holes on the inside of the sides, 2 near the front and 2 near the back.
  33. File frames — Lower the 2 file frames 122165 into the hooks, one near the front and one near the back. The hooks can also go in the other holes to suit your files.
  34. Fit the drop-file drawer — Pull the ball-bearing runners in the unit forward, line the drawer up with the bottom opening and push it in. To take it out again, pull it open and press the black levers on the runners.
  35. Done! — Your MICKE drawer unit is ready to roll under your desk. Lock the front castors to keep it in place. Max load: 1 kg per small drawer, 5 kg in the drop-file drawer.

MICKE drawer unit with drop-file storage: questions and answers

How long does it take to assemble the IKEA MICKE drawer unit with drop-file storage?

About 2–3 hours for 1 person, working through the 35 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the MICKE drawer unit with drop-file storage?

Flat & Phillips screwdriver, hammer.

Can one person assemble the MICKE drawer unit with drop-file storage?

Yes, it is a one-person build.

What size is the MICKE drawer unit with drop-file storage once assembled?

35x75 cm, as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the MICKE drawer unit with drop-file storage?

135 fittings of 20 kinds, the most numerous being 24 × screw, 18 × cam screw, 18 × wooden dowel. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA MICKE drawer unit with drop-file storage assembly instructions PDF?

The official PDF is manual AA-487829-7, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 502.130.80 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-487829-7. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example drawer runner set 112482). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA MICKE assembly guides · All dressers & drawers assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained