Step by StepAssembly Find your furniture

IKEA HEMNES 3-drawer dresser assembly instructions

How to assemble the IKEA HEMNES 3-drawer dresser (chest of drawers), step by step: 47 animated steps built from the official manual, about 2–3 hours for 2 people, with flat & Phillips screwdriver, hammer, drill (wall fixing), pencil.

IKEA HEMNES 3-drawer dresser, assembled

Solid pine dresser with a frame-and-panel look: two side frames, front rails, a drawer interlock, 3 drawers on runners and wall anchoring. Size: 108×50×96 cm (42 1/2×19 5/8×37 3/4"). About 2–3 hours, 2 people. Tools: Flat & Phillips screwdriver, Hammer, Drill (wall fixing), Pencil.

Based on the official IKEA manual AA-2406536-4 (PDF). Guide updated .

HEMNES 3-drawer dresser: quick facts
Steps47
Time2–3 hours
People2
ToolsFlat & Phillips screwdriver, Hammer, Drill (wall fixing), Pencil
Size108×50×96 cm (42 1/2×19 5/8×37 3/4")
Official manualAA-2406536-4
IKEA article number705.761.93 (white stain)
Pieces in the box240

In the box

PartPart numberQuantity
Leg4
Side panel2
Back strip (1 with drawer interlock)2
Front rail4
Rear apron1
Top1
Back panel1
Drawer front3
Drawer side6
Drawer back3
Drawer bottom3
Cam screw11833128
Dowel1013536
Dowel10135024
Cam lock11063040
Screw10771612
Screw1002144
Hex key1000011
Nails 101221 (bag)1
Fastener 144575 +1445744
Knob1176156
Dowel10134512
Knob screw1199766
Drawer back fixing11051914
Cam screw12349212
Screw1008057912
Screw1053446
Runner set100852613
Drawer centre bar100544663
Glide 191064/1910654
Wall bracket1069892
Screw1090492
Wall screw1095672
Wall plug100872232
Washer1008234

Steps

  1. Cam screws into the 4 legs — Lay the four legs on a soft surface, marked L1, L2, R2, R1, with the holes facing up. Screw 3 cam screws 118331 into each leg with a Phillips screwdriver, only until the collar meets the wood (don't overtighten).
  2. Side panels between the legs — Push 2 dowels 101350 into each long edge of both side panels (8 in total). Lay each panel between its pair of legs (the marked edge as the manual shows) and push the legs onto the dowels. Check: Use the short dowels 101350 here, not the long 101353.
  3. 12 cam locks into the side panels — Put the 12 cam locks 110630 into the holes next to the legs, 6 per side, and turn them clockwise with a flat screwdriver until they grip the cam screws in the legs.
  4. Back strips onto 6 dowels — Push 3 long dowels 101353 into each back leg. Slide a back strip onto them on both side frames: the plain strip on the left frame, the strip with the drawer interlock on the right frame (the interlock faces into the dresser).
  5. Runners "IKEA CR" on the right frame — Lay the 3 runners marked IKEA CR on the right side frame, wheel at the front, and fix each with 2 screws 107716 (use 107716, not 10080579).
  6. Runners "IKEA CL" on the left frame — Fix the 3 runners marked IKEA CL to the left side frame in the same way, 2 screws 107716 each.
  7. Glides under the 4 legs — Press a glide 191064/191065 into the hole in the bottom end of each leg.
  8. 10 cam screws for the rails — Screw 5 cam screws 118331 into the inside of each side frame: 4 in the front leg for the rails and 1 in the back leg for the rear apron. Only until the collar meets the wood.
  9. Dowels into the rails and apron — Take hardware bag 2. Push one dowel 101350 into each end of the 4 front rails and of the rear apron (10 dowels).
  10. Top front rail into the right frame — With the right side frame lying inside up, stand the top front rail (the flat one with screw holes) on the top end of the front leg, pushing its dowel and cam hole onto the cam screw.
  11. Other 3 front rails — Stand the other 3 front rails on the front leg in the same way, open side facing as shown.
  12. Lock the rails: 4 cam locks — Insert a cam lock 110630 into the underside of each rail next to the right frame and turn it clockwise to lock it on the cam screw.
  13. Rear apron into the right frame — Stand the rear apron at the bottom of the back of the right frame, on its dowel and cam screw.
  14. Lock the apron: 1 cam lock — Insert one cam lock 110630 into the apron next to the right frame and turn it to lock.
  15. Left frame on top — Turn the left side frame over and lower it onto the rails and apron, so all dowels and cam screws go into their holes. Check: Two people recommended.
  16. Lock the left side: 5 cam locks — Insert 5 cam locks 110630 on the left side (4 rails + apron) and turn them clockwise to lock.
  17. Wall brackets on the top — Lay the top upside down. Screw the 2 wall brackets 106989 to the back edge with a screw 109049 and a washer 100823 each, the bent leg pointing up.
  18. 6 cam screws into the top — Screw 6 cam screws 118331 into the underside of the top, 3 at each end.
  19. Stand it up, 6 dowels on top — Carefully tip the dresser up onto its legs. Push 3 dowels 101350 into the top of each side frame. Check: Two people recommended.
  20. Top on — Turn the top over and lower it onto the dresser so the dowels and cam screws go into their holes. The brackets go at the back.
  21. 4 screws through the top rail — From below, screw 4 screws 100214 up through the top front rail into the top with the hex key 100001.
  22. Lock the top: 6 cam locks — Insert 6 cam locks 110630 into the side panels under the top, 3 per side, and turn them clockwise to lock the top.
  23. On its front, slide in the back panel — Lay the dresser on its front on something soft (books under the top edge). Slide the back panel in from the bottom end, along the back legs, as far as it goes towards the top. Check: Two people recommended.
  24. 4 fasteners into the apron — Press 4 plugs 144575 through the back panel into the rear apron, then press a pin 144574 into each plug.
  25. Square it: 2 nails at the top — Check the dresser is square, then hammer one nail 101221 through each top corner of the back panel into the back legs, the same distance from the edge on both sides.
  26. 12 nails, then stand it up — Hammer 12 more nails 101221 along both sides of the back panel into the back legs. Then stand the dresser up again.
  27. Against the wall, mark the holes — Push the dresser against the wall. Mark the wall through the slot in each wall bracket with a pencil. Check: This dresser must be fixed to the wall to prevent tip-over. Wall screws/plugs suit most walls; ask a professional if unsure.
  28. Pull the dresser away — Pull the dresser away from the wall so you can drill.
  29. Drill and plug the wall — Drill at the marks (8 mm / 5/16" for the plugs in solid or hollow walls, 3 mm / 1/8" without plugs in solid wood) and tap in the 2 wall plugs 10087223. Check: Use fixings that suit your wall. If unsure, ask a professional.
  30. Screw the brackets to the wall — Push the dresser back against the wall. Reaching in through the top drawer opening, screw each bracket to the wall with a screw 109567 and a washer 100823. Check: Always fix the dresser to the wall: it prevents tip-over.
  31. Drawers: cam screws into the fronts — Take hardware bag 3. Lay the 3 drawer fronts face down (2 small, 1 large) and screw 4 cam screws 123492 into each, 12 in total.
  32. Dowels into the drawer sides — Push 2 dowels 101345 into the front end of every drawer side (4 per drawer, 12 in total).
  33. Sides onto the fronts — Stand two sides on each front, pushing the dowels and cam screws into the holes, grooves facing in. On the top drawer, the side with the warning sticker goes as shown in the manual.
  34. 4 cam locks per drawer — Insert 4 cam locks 110630 into each drawer (2 per side) and turn them clockwise to lock (12 in total).
  35. Slide in the drawer bottoms — Slide a drawer bottom down into the grooves of each drawer, all the way to the front.
  36. Drawer backs on — Put the back on each drawer and hammer in the fixings 110519 through the sides: 4 on each small drawer, 6 on the large one (14 in total).
  37. Centre bar: front end — Slide the bottom out to the side a little. Put the centre bar 10054466 in place under the bottom and screw its front end to the drawer front with one screw 105344.
  38. Centre bar: back end — Swing the bar straight, screw its other end to the drawer back with one screw 105344, and slide the bottom back in.
  39. Runners under the drawers — Turn each drawer upside down. Press a drawer runner 10085261 onto the bottom edge of each side and fix it with 2 screws 10080579 (4 per drawer, 12 in total).
  40. Knobs — Turn the drawers upright. Hold a knob 117615 against the front and screw it on from the inside with a screw 119976: 2 knobs per drawer.
  41. Interlock: top drawer position — Inside the dresser, on the interlock strip at the back of the right side, flip the latch for the top drawer down until it clicks. Check: Never remove or disable the drawer interlock: it lets only one drawer open at a time and helps prevent tip-over.
  42. Top drawer in — Put the top drawer (the one with the warning sticker) on the runners with the front tilted down, then lower it and push it all the way in.
  43. Interlock: bottom drawer position — Flip the latch for the bottom drawer down until it clicks.
  44. Bottom drawer in — Fit the large drawer in the bottom opening in the same way.
  45. Interlock: middle drawer position — Flip the latch for the middle drawer down until it clicks.
  46. Middle drawer in — Fit the last drawer in the middle opening. Open only one drawer at a time.
  47. Done! — Your HEMNES 3-drawer dresser is assembled and fixed to the wall. Put the heaviest things in the bottom drawer, never put a TV on it and never open more than one drawer at a time.

HEMNES 3-drawer dresser: questions and answers

How long does it take to assemble the IKEA HEMNES 3-drawer dresser?

About 2–3 hours for 2 people, working through the 47 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the HEMNES 3-drawer dresser?

Flat & Phillips screwdriver, hammer, drill (wall fixing), pencil.

Can one person assemble the HEMNES 3-drawer dresser?

It is planned as a 2-person build. One person can do most of it, but get help for steps 15, 19 and 20, where the furniture is lifted or turned.

Does the HEMNES 3-drawer dresser need to be fixed to the wall?

The manual shows a wall fixing: see step 17 (Wall brackets on the top) and step 27 (Against the wall, mark the holes). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the HEMNES 3-drawer dresser once assembled?

108×50×96 cm (42 1/2×19 5/8×37 3/4"), as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the HEMNES 3-drawer dresser?

209 fittings of 23 kinds, the most numerous being 40 × cam lock, 28 × cam screw, 24 × dowel. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA HEMNES 3-drawer dresser assembly instructions PDF?

The official PDF is manual AA-2406536-4, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 705.761.93 (white stain); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2406536-4. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example cam screw 118331). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA HEMNES assembly guides · All dressers & drawers assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained