Step by StepAssembly Find your furniture

IKEA HEMNES bookcase assembly instructions

How to assemble the IKEA HEMNES bookcase, step by step: 28 animated steps built from the official manual, about 1.5–2.5 hours for 2 people, with flat & Phillips screwdriver, hex key (included), pencil, spirit level.

IKEA HEMNES bookcase, assembled

Solid pine bookcase with framed sides: rails and a fixed shelf on cam locks, a two-part back panel, adjustable feet, 5 loose shelves and wall anchoring. Size: 90×37×197 cm (35 3/8×14 5/8×77 5/8"). About 1.5–2.5 hours, 2 people. Tools: Flat & Phillips screwdriver, Hex key (included), Pencil, Spirit level.

Based on the official IKEA manual AA-2326990-3 (PDF). Guide updated .

HEMNES bookcase: quick facts
Steps28
Time1.5–2.5 hours
People2
ToolsFlat & Phillips screwdriver, Hex key (included), Pencil, Spirit level
Size90×37×197 cm (35 3/8×14 5/8×77 5/8")
Official manualAA-2326990-3
IKEA article number604.135.02
Pieces in the box123

In the box

PartPart numberQuantity
Side frame2
Shelf rail2
Foot block2
Back rail2
Front rail2
Fixed shelf1
Top1
Back panel2
Shelf5
Hex key1000011
Screw 100211/10021213
Washer1008234
Dowel10135016
Adjustable foot1027284
Shelf pin10417112
Shelf support1064148
Screw10956011
Cam lock 113434/12233212
Cam screw11833112
Wall bracket1192562
Back panel clip1227239

Steps

  1. Cam screws into both side frames — Lay the two side frames flat on a soft surface, inside facing up and the grooved back posts as the manual shows. Screw 4 cam screws 118331 into each frame (8 in total) with a Phillips screwdriver.
  2. Dowels into the shelf rails — Take the two short shelf rails and push 3 dowels 101350 into each: 2 in the long face and 1 in one end (6 in total).
  3. Shelf rails onto the side frames — Slide a shelf rail onto each frame from the back edge, pushing its end dowel into the front post. Fix the back end of each rail with one screw 100211 using the hex key.
  4. Foot blocks on the back posts — Place a foot block on the bottom end of each back post and fix it with 2 screws 100211 and the hex key (4 in total).
  5. Adjustable feet — Screw an adjustable foot 102728 by hand into the bottom end of each post: 2 per frame, 4 in total.
  6. Back bottom rail — Push a dowel 101350 into the foot block of the frame on the floor. Stand a plain back rail (2 small holes, facing you) on the block, onto the dowel and cam screw.
  7. Back top rail — Push a dowel into the top end of the back post and stand the second plain back rail on it in the same way.
  8. The two front rails — Push a dowel into the front post at each end and stand the two front rails on them: the plinth rail at the bottom end and the top rail at the top end.
  9. Lock the 4 rails — Insert a cam lock 113434/122332 into the hole at the lower end of each rail and turn it clockwise with a flat screwdriver until it grips.
  10. Cam screws into the shelf rails — Screw 2 cam screws 118331 into each shelf rail, next to the dowels (4 in total).
  11. Fixed shelf — Lower the fixed shelf onto the shelf rail of the frame on the floor, cam lock holes towards the bottom end. Lock it with 2 cam locks.
  12. Second side frame on top — Push a dowel 101350 into the top end of each of the 4 rails. Turn the other side frame over and lower it onto all the rails and the fixed shelf. Check: This frame is long: two people make this easier.
  13. Lock the top frame, lay it on its front — Insert 6 cam locks on this side (4 in the rails, 2 in the fixed shelf) and turn them to lock. Then carefully roll the bookcase onto its front.
  14. Dowels and top — With the bookcase on its front (on soft supports), push a dowel 101350 into the top end of each side frame and press the top onto them, the edge with holes at the back.
  15. Screw the top on — Fix the top with 7 screws 100211 and the hex key: 4 into the posts and 3 into the front top rail.
  16. Upper back panel into the lower groove — Roll the bookcase back onto its side. Check the upper back panel is the right way round, then bend it slightly and slide its edge down into the groove of the bottom side frame. Check: The smooth side of the back panel faces into the bookcase.
  17. Into the upper groove — Push the panel flat so its other edge slips into the groove of the top side frame and its top edge sits under the top rail.
  18. Lower back panel — Slide the lower back panel down into the groove of the bottom side frame in the same way. Check: Two people: one holds the bookcase steady while the other bends the panel in.
  19. Push the lower panel home — Push the lower panel flat so its other edge slips into the groove of the top side frame and its end sits under the bottom back rail.
  20. Clips along the panel seam — With two people, lay the bookcase on its front. Fix 3 clips 122723 across the seam between the two back panels with screws 109560, raised side facing out.
  21. Clips along the top and bottom — Fix 3 more clips with screws 109560 along the top edge and 3 along the bottom edge of the back (6 in total).
  22. Stand it up and level it — Tip the bookcase up onto its feet, turn it round and place it against the wall. Check with a spirit level on the top and turn the adjustable feet as needed until it stands level and steady. Check: Two people are needed to raise the bookcase.
  23. Fix it to the wall — Screw the 2 wall brackets 119256 to the top with a screw 109560 and a washer 100823 each. Then fix each bracket to the wall through its upright slot with a washer 100823 and a screw that suits your wall. Check: Must be fixed to the wall to stop it tipping over. Wall screws and plugs are not included: ask your local hardware store what suits your wall.
  24. Pins for the bottom shelf — Push 4 shelf pins 104171 into the lowest holes, 2 on each side, thin end first.
  25. Bottom shelf — Tilt the bottom shelf to get it past the front posts, then lower it onto the 4 pins, the notched corners at the front around the front posts.
  26. Shelf pins and supports — For the 4 adjustable shelves, push 8 shelf pins 104171 into the back posts and 8 shelf supports 106414 into the front posts, at the same heights on both sides.
  27. Put in the shelves — Tilt each shelf to slide it in past the front posts, set its back edge on the pins, then press the front down onto the supports until it clicks in.
  28. Done! — Your HEMNES bookcase is assembled and fixed to the wall. Max load: 30 kg per shelf. Re-check the wall fixing and the feet from time to time.

HEMNES bookcase: questions and answers

How long does it take to assemble the IKEA HEMNES bookcase?

About 1.5–2.5 hours for 2 people, working through the 28 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the HEMNES bookcase?

Flat & Phillips screwdriver, hex key (included), pencil, spirit level. Already in the box: Hex key.

Can one person assemble the HEMNES bookcase?

It is planned as a 2-person build. One person can do most of it, but get help for steps 12, 20 and 22, where the furniture is lifted or turned.

Does the HEMNES bookcase need to be fixed to the wall?

The manual shows a wall fixing: see step 23 (Fix it to the wall) and step 28 (Done). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the HEMNES bookcase once assembled?

90×37×197 cm (35 3/8×14 5/8×77 5/8"), as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the HEMNES bookcase?

104 fittings of 12 kinds, the most numerous being 16 × dowel, 13 × screw 100211/100212, 12 × shelf pin. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA HEMNES bookcase assembly instructions PDF?

The official PDF is manual AA-2326990-3, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 604.135.02; other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2326990-3. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example hex key 100001). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA HEMNES assembly guides · All bookcases & shelves assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained