Step by StepAssembly Find your furniture

IKEA HEMNES sideboard assembly instructions

How to assemble the IKEA HEMNES sideboard, step by step: 61 animated steps built from the official manual, about 4–5 hours for 2 people, with flat & Phillips screwdriver, hammer, hex key (included), pencil & ruler, drill + wall screws (wall fixing).

IKEA HEMNES sideboard, assembled

Solid pine sideboard with a light brown top: three drawers between two cabinets with doors and a shelf, built on its front from two leg frames. Size: 157x88 cm. About 4–5 hours, 2 people. Tools: Flat & Phillips screwdriver, Hammer, Hex key (included), Pencil & ruler, Drill + wall screws (wall fixing).

Based on the official IKEA manual AA-1422820-10 (PDF). Guide updated .

HEMNES sideboard: quick facts
Steps61
Time4–5 hours
People2
ToolsFlat & Phillips screwdriver, Hammer, Hex key (included), Pencil & ruler, Drill + wall screws (wall fixing)
Size157x88 cm
Official manualAA-1422820-10
IKEA article number704.762.59
Pieces in the box266

In the box

PartPart numberQuantity
Top (light brown)1
End frame (legs + side panel)2
Bottom shelf1
Plinth rail1
Front top rail1
Partition2
Front rail (between drawers)2
Centre leg1
Back leg block2
Back panel (fibreboard)1
Shelf2
Door2
Drawer front3
Drawer side6
Drawer back3
Drawer bottom3
Drawer runner set1124823
Cam lock11063012
Screw10036530
Knob1176155
Connector screw12349212
Knock-in fixing11051912
Dowel10134512
Screw1004135
Screw1002149
Cam screw11833124
Cam screw1004816
Dowel10135036
Door stop1015772
Cam lock11343430
Hex key1000011
Wall bracket1192562
Screw10956010
Washer1008234
Hinge1237722
Hinge 123746 (soft-close)2
Mounting plate1287114
Screw1002112
Shelf support1041718

Steps

  1. Dowels into the drawer sides — You build 3 drawers with bag 1: the first in full, the other two together. Lay each pair of drawer sides flat and push 2 dowels 101345 into the front end of each side (4 per drawer). Check: Use the short dowels 101345 here, not the thicker 101350 from bag 2.
  2. Connector screws into the fronts — Lay each drawer front face down on a soft surface, groove up. Screw 4 connector screws 123492 into the holes near its ends with a Phillips screwdriver.
  3. Sides onto the fronts — Stand the two sides on each front, dowel ends down, so the dowels and connector screws go into their holes. The large cam lock holes face outwards.
  4. Lock the sides — Push a cam lock 110630 into each of the 4 holes on the outside of the sides, arrow towards the screw, and turn it clockwise with a flat screwdriver until it grips.
  5. Slide in the drawer bottoms — Slide each fibreboard bottom down the grooves in the sides from the open end until it sits in the groove of the front.
  6. Backs on top — Put each drawer back between the top ends of the sides, over the bottom.
  7. Knock in the back fixings — Push 4 fixings 110519 through the sides into the ends of the back (2 per side) and tap them home with a hammer.
  8. Knobs on the drawer fronts — Tip each drawer upright. Hold a knob 117615 against the front and screw a screw 100413 through the front from inside into it with a Phillips screwdriver.
  9. Drawer runners on — Turn each drawer upside down. Lay the two drawer runners of a runner set 112482 on the bottom edges of the sides, wheel at the back and the flange against the outside.
  10. Screw the drawer runners — Fix each drawer runner with 2 screws 100365 into the side (4 per drawer). Put the drawers aside.
  11. Cabinet runners on the partitions — Take bag 2. Lay both partitions flat, inside up, notches at the same end. Screw the 3 runners marked L to one partition and the 3 marked R to the other, wheel towards the notched edge, 3 screws 100365 each.
  12. Cam screws for the front rails — Screw 2 cam screws 118331 into the inside face of each partition, near the notched edge (4 in total), only until the collar meets the wood. Check: Use 118331 here, not the shorter 100481.
  13. Stand the front rails up — Push a dowel 101350 into each end of the 2 front rails, then stand both rails on the cam screws of the partition with the L runners, cam holes towards the runners.
  14. Lock the rails — Push a cam lock 113434 into the hole at the lower end of each rail and turn it clockwise with a flat screwdriver.
  15. Second partition on — Tip the partition up so the rails lie level. Stand the other partition up, runners facing in, and push it onto the dowels and cam screws at the rail ends. Lock with 2 cam locks 113434.
  16. Mounting plates on the end frames — Lay both end frames inside up, front legs (the ones with the foot holes) towards each other. Screw 2 hinge mounting plates 128711 to the inside of each front leg with their own screws.
  17. 10 cam screws in the end frames — Screw 5 cam screws 118331 into the inside of each end frame: one near each end of the front leg and 3 along the bottom side rail. Stop when the collar meets the wood.
  18. Cam screws in the plinth rail — Lay the bottom shelf upside down, the side with the cam lock holes up. Lay the long plinth rail beside its front edge and screw 4 cam screws 118331 into the face that will meet the shelf.
  19. 10 dowels — Push dowels 101350 into the bottom shelf: 2 in each end and 4 along the front edge. Push one into each end of the plinth rail.
  20. Plinth rail onto the shelf — Turn the plinth rail up and press it against the front edge of the shelf over the dowels and cam screws. Lock it with 4 cam locks 113434 in the shelf.
  21. Bottom onto the left end frame — With a helper, stand the left end frame on its front leg, inside facing the middle. Turn the bottom shelf up onto the plinth rail and push it onto the frame's dowels and cam screws.
  22. Lock the bottom — Push 4 cam locks 113434 into the holes at the frame end: 3 in the underside of the bottom shelf and 1 in the plinth rail. Turn them clockwise.
  23. Front top rail — Push a dowel 101350 into each end of the front top rail. Lay it on the floor at the top end of the frame's front leg and slide it onto the dowel and cam screw.
  24. Lock the front top rail — Push a cam lock 113434 into the hole near the end of the rail and turn it clockwise with a flat screwdriver.
  25. Dowels in the partitions — Push 2 dowels 101350 into the bottom edge of each partition (the end without the notch).
  26. Partitions in — Lift the partition unit into the carcass, front rails down, and lower it just short of the bottom shelf so the notches go over the front top rail. Then push it onto the bottom shelf so the dowels go into their holes.
  27. Screw the partitions — Screw 4 screws 100214 through the underside of the bottom shelf into the partitions, 2 each, with the hex key 100001.
  28. Right end frame on — Stand the right end frame on its front leg at the other end and push it onto the dowels and cam screws of the bottom shelf, plinth rail and front top rail.
  29. Lock the right end frame — Push 5 cam locks 113434 into the holes at this end: 3 in the bottom shelf, 1 in the plinth rail and 1 in the front top rail. Turn them clockwise.
  30. Centre leg — Hold the centre leg against the underside of the bottom shelf, behind the plinth rail. From inside, screw a screw 100214 through the shelf into it with the hex key.
  31. Stand it up — With a helper, stand the carcass up on its legs. The back now faces you.
  32. 12 dowels on top — Push 12 dowels 101350 into the top ends: 4 in the front top rail, 2 in each partition and one in each leg.
  33. Cam screws in the top — Lay the top face down on a soft surface. Screw 3 short cam screws 100481 into each end and 6 cam screws 118331 into the middle (3 per partition), only until the collar meets the wood. Check: The short cam screws 100481 go at the ends, over the end frames.
  34. Top on — With a helper, turn the top over and lower it onto the carcass so the dowels and cam screws go into their holes, the back edges flush.
  35. Lock the top — Push 12 cam locks 113434 into the holes under the top: 3 in each end frame and 3 in each partition. Turn them clockwise with a flat screwdriver.
  36. Screws through the front top rail — Screw 4 screws 100214 up through the front top rail into the top with the hex key.
  37. Onto its front — With a helper, tip the sideboard forward onto its front, back facing up.
  38. Mark the partitions — Make a pencil mark on the back edge of the top in line with the middle of each partition.
  39. Slide in the back panel — Slide the fibreboard back panel into the grooves of the back legs from the bottom end until it meets the top. The 2 notches go at the top end.
  40. Draw the screw lines — With a ruler, draw a line across the back panel from each pencil mark, so you can see where the partitions are.
  41. Screw the back panel — Press the back panel down and screw 8 screws 109560 through it: 3 along each line into the partitions and 1 into each corner of the bottom shelf.
  42. Dowels in the back leg blocks — Take the 2 back leg blocks and push 2 dowels 101350 into the side of each.
  43. Back leg blocks on — Hold each block under the bottom shelf against the inside of a back leg, push it onto the dowels and screw a screw 100211 through it into the leg with the hex key.
  44. Stand it up — With a helper, stand the sideboard back up on its legs.
  45. Against the wall — The sideboard must be fixed to the wall. Turn it round and stand it with its back against the wall where it will go. Check: Fix it to the wall so it cannot tip over.
  46. Mark the wall — Through each of the 2 notches at the top of the back panel, draw a line on the wall along the underside of the top.
  47. Pull it away — Pull the sideboard away from the wall and move it aside so you can work on the wall.
  48. Wall brackets on — Hold each wall bracket 119256 on the wall with its top edge on your line and screw it on through a washer 100823. Wall screws are not included: choose ones suited to your wall. Check: Ask your local hardware shop if you are unsure which screws suit your wall.
  49. Back against the wall — Push the sideboard back against the wall so the brackets slide in through the notches, under the top.
  50. Screw the brackets to the top — Screw each bracket to the underside of the top with a washer 100823 and a screw 109560 through the slot.
  51. Shelf supports — Push 8 shelf supports 104171 into the holes at the height you want, 4 in each door cabinet, at the same height on both sides. Check: Push the thin peg of each support into the hole, not the other way round.
  52. Shelves in — Tilt each shelf, slide it in above the supports and lower it onto them.
  53. Fold the hinges — Take the 4 hinges: 2 soft-closing hinges 123746 and 2 hinges 123772. Fold each one closed as shown.
  54. Soft-closing hinges into the doors — Lay both doors face down. Press a soft-closing hinge 123746 into the top hinge hole of each door and tighten its 2 screws with a Phillips screwdriver.
  55. Other hinges into the doors — Press a hinge 123772 into the bottom hinge hole of each door and tighten its 2 screws.
  56. Open the hinges — Fold all 4 hinges open again.
  57. Hang the doors — Hold each door open beside its end frame and push the hinges onto the mounting plates until they click (4 hinges). Check: To take a door off later, press the release on each hinge.
  58. Door knobs — Hold a knob 117615 on the front of each door and screw a screw 100413 into it through the door from the inside.
  59. Door stops — Push a door stop 101577 into the hole in the front edge of each shelf, at the end next to the drawers. Close the doors: they stop against it.
  60. Drawers in — Turn each drawer upright, line its runners up with the runners in its opening and slide it in until it closes. Start with the bottom drawer.
  61. Done! — Your HEMNES sideboard is finished and fixed to the wall. Each shelf holds up to 12 kg and each drawer up to 10 kg; check the wall fixing now and then.

HEMNES sideboard: questions and answers

How long does it take to assemble the IKEA HEMNES sideboard?

About 4–5 hours for 2 people, working through the 61 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the HEMNES sideboard?

Flat & Phillips screwdriver, hammer, hex key (included), pencil & ruler, drill + wall screws (wall fixing). Already in the box: Hex key.

Can one person assemble the HEMNES sideboard?

It is planned as a 2-person build. One person can do most of it, but get help for steps 13, 15 and 20, where the furniture is lifted or turned.

Does the HEMNES sideboard need to be fixed to the wall?

The manual shows a wall fixing: see step 46 (Mark the wall) and step 48 (Wall brackets on). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the HEMNES sideboard once assembled?

157x88 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the HEMNES sideboard?

231 fittings of 22 kinds, the most numerous being 36 × dowel, 30 × screw, 30 × cam lock. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA HEMNES sideboard assembly instructions PDF?

The official PDF is manual AA-1422820-10, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 704.762.59; other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-1422820-10. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example drawer runner set 112482). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA HEMNES assembly guides · All bookcases & shelves assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained