Step by StepAssembly Find your furniture

IKEA HEMNES day-bed frame with 3 drawers assembly instructions

How to assemble the IKEA HEMNES day-bed frame with 3 drawers (daybed), step by step: 46 animated steps built from the official manual, about 4–5 hours for 2 people, with flat screwdriver, Phillips screwdriver, hammer.

IKEA HEMNES day-bed frame with 3 drawers, assembled

White day bed with a frame-and-panel back and ends, a pull-out slatted base on castors that turns it into a double bed, and 3 big drawers on runners. Size: 80×200 cm (209×89×83 cm), pulls out to 160×200 cm. About 4–5 hours, 2 people. Tools: Flat screwdriver, Phillips screwdriver, Hammer.

Based on the official IKEA manual AA-1913852-7 (PDF). Guide updated .

HEMNES day-bed frame with 3 drawers: quick facts
Steps46
Time4–5 hours
People2
ToolsFlat screwdriver, Phillips screwdriver, Hammer
Size80×200 cm (209×89×83 cm), pulls out to 160×200 cm
Official manualAA-1913852-7
IKEA article number903.493.26 (white)
Pieces in the box363

In the box

PartPart numberQuantity
Beam (pull-out base)4
Back panel (pull-out base)1
Front panel with 3 openings1
End panel (pull-out base)2
Short slat (pull-out base)13
Long slat (frame)12
End support (marked slat)2
Back panel (frame)1
End panel (frame)2
Back top rail1
Armrest cap2
Steel angle1129753
Steel front rail1129771
Drawer front3
Drawer back3
Drawer side6
Drawer bottom3
Castor1114018
Screw10904916
Runner set 139505 (CR, CL, DR, DL)3
Screw10034736
Dowel10135034
Screw11689450
Cam screw11833140
Cam lock10343016
Pin11052532
Bolt1052364
Barrel nut1089034
Hex key1000011
Glide1535524
Clip1304852
Screw1090604
Bracket1236602
Dowel10401217
Cam lock10311424
Knob1176153
Screw1199763

Steps

  1. Castors on the 4 beams — Part 1 is the pull-out base. Lay the 4 beams on a soft surface with the castor holes facing up. Screw 2 castors 111401 onto each beam, 2 screws 109049 per castor (8 castors, 16 screws).
  2. Runners marked CR on 3 beams — Turn the beams over onto their castors. Screw a cabinet runner marked CR onto the side of 3 of the beams (not the far-left one), with the wheel at the front end, using 3 screws 100347 each. Check: Use the short screws 100347 for the runners, not 116894.
  3. Runners marked CL on the other sides — Screw a cabinet runner marked CL onto the other side of 3 beams (not the far-right one), again with 3 screws 100347 each. Each drawer will run between a CL and a CR runner. Check: Use the short screws 100347 for the runners, not 116894.
  4. Dowels in the beam ends — Push 2 dowels 101350 into both ends of every beam (16 in total), into the outer two of the three end holes.
  5. Steel angle on the back panel — Lay the plain back panel of the base face down on a soft surface. Place a steel angle 112975 along its long edge and fix it at both ends with 2 screws 116894 through the slots. Check: Use the screws 116894 here, not 100347.
  6. 6 more screws in the angle — Fix the rest of the steel angle with 6 screws 116894 in the slots along its length. Check: Use the screws 116894 here, not 100347.
  7. Cam screws in the back panel — Screw 8 cam screws 118331 into the holes in the inside face of the back panel: 3 at each end and 1 at each of the two middle beam positions.
  8. Stand the beams on the back panel — Stand the 4 beams up on the back panel, castors facing the same way as the manual shows and the runners on the correct sides, so the dowels and cam screws go into the beam ends.
  9. Lock the beams — Push a cam lock 103430 into the hole near the bottom of each beam and turn it clockwise with a flat screwdriver to pull the beam tight against the back panel (4 cam locks).
  10. Dowels in the end panels — Push 3 dowels 101350 into each short edge of the two small end panels (12 dowels in total).
  11. End panels on — Stand the two end panels on the ends of the back panel, against the outer beams, with the dowels and cam screws going into their holes.
  12. Lock the end panels — Push 2 cam locks 103430 into each end panel, next to the back panel, and turn them clockwise to lock (4 cam locks). On the left end panel they go in from the outside, on the right one from the inside.
  13. Steel angle on the front panel — Lay the front panel (with the 3 openings and the curved top) face down on a soft surface. Place the second steel angle 112975 along its top edge and fix it at both ends with 2 screws 116894. Check: Use the screws 116894 here, not 100347.
  14. 6 more screws in the angle — Fix the rest of the steel angle with 6 screws 116894. Check: Use the screws 116894 here, not 100347.
  15. Cam screws in the front panel — Screw 8 cam screws 118331 into the inside face of the front panel, in the same pattern as the back panel.
  16. Front panel on top — Turn the front panel over and lower it onto the beams and end panels, steel angle inside, so the cam screws go into their holes.
  17. Lock the end panels at the front — Push 2 cam locks 103430 into each end panel next to the front panel and turn them to lock (4 cam locks): from the outside on the left, from the inside on the right.
  18. Lock the beams at the front — Push a cam lock 103430 into the top end of each beam and turn it to lock the beams to the front panel (4 cam locks).
  19. Screw in 3 slats — Pick the 13 shorter slats (the 14 longer ones are for the bed frame). Fit 3 of them across the base, one at each end and one in the middle, and screw each one to both steel angles with screws 116894 (6 screws), using hole 2 at the ends. Check: Check the slat length first: the short slats belong in the pull-out base.
  20. Pins in the other 10 slats — Push 2 pins 110525 into the holes near the ends of each of the other 10 short slats (20 pins).
  21. Stand the base up, lay the slats — With two people, tip the base onto its castors. Lay the 10 slats across it with the pins down, into the holes in the steel angles.
  22. Steel angle on the bed back — Part 2 is the day-bed frame. Lay the big grooved back panel on a soft surface, grooved side up. Place the third steel angle 112975 along the marked line near its bottom edge and fix both ends with 2 screws 116894. Check: Use the screws 116894 here, not 100347.
  23. 6 more screws — Fix the rest of the angle with 6 screws 116894. Check: Use the screws 116894 here, not 100347.
  24. Dowels in the end panels — Lay both end panels inside face up. Push 3 dowels 101350 into the back post of each one (6 dowels).
  25. Bolt the frame together (upside down) — Stand the back panel and the end panels upside down on a soft surface. Push 4 barrel nuts 108903 into the back panel, slot facing the bolt, then join the end panels to it with 4 bolts 105236 and the hex key 100001. Check: Tighten the bolts fully only when all four are in.
  26. Glides under the posts — Press a glide 153552 into the end of each of the 4 posts (the post ends are on top while the frame is upside down).
  27. Steel front rail — Fit the steel front rail 112977 between the two front posts, with a clip 130485 at each end, and fix each end with 2 screws 109060. Check: Use the long screws 109060 here, not 116894.
  28. Turn it over; brackets on the end supports — With two people, turn the frame the right way up. Pick the 2 slats with the extra holes on the edge (the other 12 are plain): screw a bracket 123660 onto the end of each one with 2 screws 116894. Check: Use the screws 116894 here, not 100347.
  29. End supports in — Lay an end support at each end of the frame, bracket at the front and towards the middle. Screw each one down at both ends with screws 116894: from below through the back angle and from above into the front rail (4 screws). Check: Use the screws 116894 here, not 100347.
  30. Pins in the 12 long slats — Push one pin 110525 into the hole at one end of each of the 12 plain long slats.
  31. Lay the slats and screw them — Lay the 12 slats across the frame with the pins at the back, into the holes in the steel angle. Fix the front end of every slat to the steel front rail with a screw 116894 (12 screws). Check: Never stand or sit on the slats before the mattress is on.
  32. Roll the pull-out base in — With two people: lift the frame a little at the ends and push the base in under the slats, front panel facing out, so its back angle passes the two brackets. Lower the frame again.
  33. Dowels in the top edges — Tap 17 dowels 104012 into the holes in the top edges of the back panel, the end panels and the posts with a hammer.
  34. Back top rail — Press the long top rail down onto the dowels along the top of the back.
  35. Armrest caps — With two people, press an armrest cap onto each end panel, notched end at the back against the top rail.
  36. Drawers: cam screws in front and back — Part 3 is the 3 drawers. For each drawer lay the front and the back inside face up and screw 4 cam screws 118331 into each (8 per drawer, 24 in total).
  37. Drawer sides on the back — Stand the two sides on the back, grooves facing in and at the bottom, so the cam screws go into the holes.
  38. Lock the sides to the back — Push 4 cam locks 103114 into the sides next to the back and turn them clockwise to lock (12 for all 3 drawers).
  39. Drawer bottom — Slide the drawer bottom down into the grooves of the sides.
  40. Drawer front on — Turn the front over and press it onto the sides, so the cam screws go into the holes.
  41. Lock the front — Push 4 cam locks 103114 into the sides next to the front and turn them to lock (12 for all 3 drawers).
  42. Drawer runners DR and DL — Stand the drawer on its bottom. Screw the drawer runner marked DR to the right side and DL to the left side along the bottom edge, 3 screws 100347 each (18 screws for the 3 drawers). Check: Use the short screws 100347 for the runners, not 116894.
  43. Knobs — Stand the drawer on its back. Hold a knob 117615 on the front and screw it on from the inside with a screw 119976.
  44. Drawers in — Put each drawer onto its runners in the pull-out base and push it in until it closes. Check: Never stand on an open drawer.
  45. Pull out to a double bed — To make a double bed, pull the base out by the front panel until it stops at the two brackets (about 70 cm) and put a second 80×200 mattress on it. Push it back in for a day bed.
  46. Done! — Your HEMNES day bed is ready. Use mattresses no thicker than the ones IKEA recommends for it, and check the bolts and screws again after a couple of weeks.

HEMNES day-bed frame with 3 drawers: questions and answers

How long does it take to assemble the IKEA HEMNES day-bed frame with 3 drawers?

About 4–5 hours for 2 people, working through the 46 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the HEMNES day-bed frame with 3 drawers?

Flat screwdriver, Phillips screwdriver, hammer.

Can one person assemble the HEMNES day-bed frame with 3 drawers?

It is planned as a 2-person build. One person can do most of it, but get help for steps 2, 8 and 16, where the furniture is lifted or turned.

What size is the HEMNES day-bed frame with 3 drawers once assembled?

80×200 cm (209×89×83 cm), pulls out to 160×200 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the HEMNES day-bed frame with 3 drawers?

304 fittings of 21 kinds, the most numerous being 50 × screw, 40 × cam screw, 36 × screw. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA HEMNES day-bed frame with 3 drawers assembly instructions PDF?

The official PDF is manual AA-1913852-7, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 903.493.26 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-1913852-7. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example steel angle 112975). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA HEMNES assembly guides · All beds assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained