IKEA MYDAL bunk bed frame assembly instructions
How to assemble the IKEA MYDAL bunk bed frame, step by step: 35 animated steps built from the official manual, about 2–3 h for 2 people, with Allen keys (included), flat-blade screwdriver, hammer, small block of wood.
Solid pine bunk bed with two slatted bases, guard rails round the top bunk and a fixed ladder at either end. Size: 90x200 cm. About 2–3 h, 2 people. Tools: Allen keys (included), Flat-blade screwdriver, Hammer, Small block of wood.
Based on the official IKEA manual AA-206907-11 (PDF). Guide updated .
| Steps | 35 |
|---|---|
| Time | 2–3 h |
| People | 2 |
| Tools | Allen keys (included), Flat-blade screwdriver, Hammer, Small block of wood |
| Size | 90x200 cm |
| Official manual | AA-206907-11 |
| IKEA article number | 001.024.52 (pine) |
| Pieces in the box | 292 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Post | 4 | |
| End top rail | 2 | |
| Narrow end board | 4 | |
| Wide end board | 4 | |
| Bed rail with slat ledge | 4 | |
| Guard rail | 4 | |
| Slat | 32 | |
| Ladder post | 1 | |
| Ladder rung | 2 | |
| Guard rail upright | 3 | |
| Bolt | 120209 | 24 |
| Bolt | 120208 | 24 |
| Barrel nut | 100514 | 48 |
| Bolt | 130718 | 15 |
| Sleeve nut | 100602 | 15 |
| Dowel | 101350 | 40 |
| Slat fastener | 110719 | 64 |
| Allen key | 100001 | 1 |
| Allen key | 100002 | 1 |
Steps
- End frame: post and top rail — Build an end frame lying flat on a rug, inside face up. Lay down a post and put the narrow top rail against its top end. Drop 2 barrel nuts 100514 into the holes in the rail, slot up, and turn them with a screwdriver so the threaded hole faces the post. Screw in 2 long bolts 120209 and tighten them with Allen key 100001. Check: Build two end frames the same way (steps 1–6). Use the long bolts 120209 for the end frames. The holes for the barrel nuts face up.
- Narrow boards with dowels — Push 2 dowels 101350 into one end of each of the two narrow boards. Fit them into the post: one just below the top rail, the other in the lower part of the post, as drawn. Check: Dowels go in straight, with the ribs lengthways.
- Wide boards with dowels — Push 1 dowel into one end of each wide board: the end with three holes. Fit them into the post: one below the upper narrow board, the other at the bottom, below the lower narrow board. Check: The barrel nut holes in the wide boards face up, like the top rail's.
- Bolt the wide boards — Drop 4 barrel nuts 100514 into the wide boards, slots lined up, and fix each board with 2 long bolts 120209 through the post, using Allen key 100001.
- Second post — Push dowels into the free ends of the four boards: 2 in each narrow board and 1 in each wide board, 6 in all. Fit the second post onto them, its holes facing the same way as the first post's.
- Bolt the second post: top rail — Drop 2 barrel nuts into the top rail at the second post and fix the post there with 2 long bolts 120209 and Allen key 100001.
- Bolt the second post: wide boards — Drop 4 barrel nuts into the two wide boards and fix them to the second post with 4 long bolts 120209. The first end frame is done.
- Second end frame (steps 1–2 again) — Build the second end frame the same way, inside face up: post and top rail with 2 barrel nuts and 2 bolts 120209, then the two narrow boards on 2 dowels each. Tighten every bolt with the Allen key.
- Second end frame (steps 3–4 again) — Fit the two wide boards on 1 dowel each, then fix them with 4 barrel nuts and 4 bolts 120209, tightened with the Allen key.
- Second end frame (steps 5–6 again) — Finish the second end frame: 6 dowels in the free board ends, the second post, then 6 barrel nuts and 6 bolts 120209, tightened with the Allen key.
- Stand up an end frame, lower bed rails — With a helper, stand one end frame up. Push a dowel 101350 into each end of the two lower bed rails, and fit the rails into the end frame's posts with the slat ledge at the bottom, on the inside. Check: Check the rail ends: the ledge sits low and points into the bed, as in the drawing.
- Bolt the lower rails to the end frame — Drop a barrel nut 100514 into each of the 4 holes near the rail ends and line its slot up with a screwdriver. Fix each rail with 2 bolts 120208 through the post, using Allen key 100001. Check: From here on use the shorter bolts 120208. Tighten until the head sits flat on the post.
- Second end frame — Stand the second end frame up and push its posts onto the dowels in the free rail ends. Fix it the same way: 4 barrel nuts and 4 bolts 120208.
- Upper back rail — Push a dowel into each end of an upper bed rail. Angle it in between the end frames at the back, ledge low and inside, and swing it onto the posts. Fix it with 4 barrel nuts and 4 bolts 120208.
- Upper front rail — Fit the second upper bed rail at the front the same way: a dowel in each end, angle it in, swing it onto the posts with the ledge low and inside, then 4 barrel nuts and 4 bolts 120208.
- First slat on each bed — Lay one slat across the middle of each bed, its ends on the ledges. Push a slat fastener 110719 into the hole at each end and drive it in by tapping a block of wood with a hammer: 4 fasteners. Check: Never hit a fastener directly with the hammer: always tap through a block of wood.
- Lay the other slats — Lay the other 15 slats on each bed, spread evenly along the ledges with the holes over the ledges: 8 on one side of the first slat, 7 on the other.
- Fasten the back ends — Fix the back end of every new slat with a slat fastener 110719, tapped in through the block of wood: 15 on each bed, 30 in all. Check: Tap through the block, never straight onto the fastener.
- Fasten the front ends — Fix the front end of all 30 new slats the same way: 15 fasteners on each bed, tapped in through the block.
- Dowels in the back guard rails — Take the two guard rails for the back and push a dowel 101350 into each end: 4 dowels.
- Fit the back guard rails — Angle each guard rail in above the top bed at the back and swing it onto the posts: one level with the tops of the posts, the other just below it, level with the narrow end boards.
- Bolt the back guard rails — Fix each end of both guard rails with a barrel nut 100514 and a bolt 120208 through the post: 4 of each, tightened with Allen key 100001.
- Tighten the bed rails: right end — Go round the bed and tighten all 16 bolts that hold the four bed rails with Allen key 100001, until each head sits flat against its post. These are the 8 at the right-hand end. Check: A bolt head that stands proud or sits crooked is not tight yet.
- Tighten the bed rails: left end — Go round the bed and tighten all 16 bolts that hold the four bed rails with Allen key 100001, until each head sits flat against its post. These are the 8 at the left-hand end. Check: A bolt head that stands proud or sits crooked is not tight yet.
- Ladder post — The ladder can go at either end; this shows the right-hand end (manual pages 19–22, the left is the mirror image on pages 23–26). Hold the ladder post against the front rails, notch at the top. Fix it with 2 bolts 130718 from inside the bed and 2 sleeve nuts 100602 from the front, using both Allen keys.
- Ladder rungs — Push a dowel 101350 into each of the two holes in the end frame's front post. Fit the two rungs between the ladder post and the end frame, their back ends behind the ladder post, and push them onto the dowels.
- Fix the rungs to the ladder post — From behind, put a bolt 130718 through the end of each rung into the ladder post and screw a sleeve nut 100602 in from the front. Hold the nut with Allen key 100002 and tighten the bolt with 100001.
- Fix the rungs to the end frame — Drop a barrel nut 100514 into the hole near the end of each rung, then fix the rung with a bolt 120208 through the end frame's post from the outside.
- Front guard rails — Push a dowel 101350 into the left end of both front guard rails. Lower them in from above between the left end frame and the ladder post, then push them onto the left post: one level with the top, the other below it.
- Fix them to the ladder post — Fix both guard rails to the ladder post: a bolt 130718 from inside the bed and a sleeve nut 100602 from the front for each.
- Fix them to the left post — At the left end, drop a barrel nut 100514 into each guard rail and fix it with a bolt 120208 through the post from the outside.
- Front upright — Hold an upright against the outside of the front guard rails and the upper front rail. Fix it with 3 bolts 130718 from inside the bed and 3 sleeve nuts 100602 from the front.
- Back uprights: left — Fix the other two uprights to the outside of the back guard rails and the upper back rail the same way: 3 bolts 130718 from inside the bed and 3 sleeve nuts 100602 from the back for each. First the left one.
- Back uprights: right — Fix the right-hand back upright the same way: 3 bolts 130718 from inside the bed, 3 sleeve nuts 100602 from the back, tightened with both Allen keys. That makes 9 of each for the three uprights.
- Done! — Your MYDAL bunk bed is assembled. Use 90×200 cm mattresses no thicker than 19 cm (top bunk), max 100 kg per bed. The top bunk is for children aged 6 and over. Check all the bolts regularly and tighten them when needed.
MYDAL bunk bed frame: questions and answers
How long does it take to assemble the IKEA MYDAL bunk bed frame?
About 2–3 h for 2 people, working through the 35 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the MYDAL bunk bed frame?
Allen keys (included), flat-blade screwdriver, hammer, small block of wood. Already in the box: Allen keys.
Can one person assemble the MYDAL bunk bed frame?
It is planned as a 2-person build. One person can do most of it, but get help for step 13, where the furniture is lifted or turned.
What size is the MYDAL bunk bed frame once assembled?
90x200 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.
How many screws and fittings come with the MYDAL bunk bed frame?
230 fittings of 7 kinds, the most numerous being 64 × slat fastener, 48 × barrel nut, 40 × dowel. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA MYDAL bunk bed frame assembly instructions PDF?
The official PDF is manual AA-206907-11, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 001.024.52 (pine); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-206907-11. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example bolt 120209). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA MALM bed frame (high, Queen) assembly instructions
- IKEA HEMNES day-bed frame with 3 drawers assembly instructions
- IKEA TUFFING bunk bed frame assembly instructions
- IKEA BRIMNES day-bed frame with 2 drawers assembly instructions
- IKEA SMÅSTAD loft bed frame w desk and storage assembly instructions
- IKEA TUFFING loft bed frame assembly instructions
- IKEA VITVAL loft bed frame assembly instructions
- IKEA VITVAL bunk bed frame assembly instructions
All beds assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained