IKEA TUFFING loft bed frame assembly instructions
How to assemble the IKEA TUFFING loft bed frame, step by step: 40 animated steps built from the official manual, about 2–3 h for 2 people, with Allen keys (included), Phillips screwdriver.
Dark grey steel-tube loft bed with a fabric guard all round, a mesh slatted base and a leaning ladder that hooks onto the front rail. Size: 90x200 cm. About 2–3 h, 2 people. Tools: Allen keys (included), Phillips screwdriver.
Based on the official IKEA manual AA-1785340-10 (PDF). Guide updated .
| Steps | 40 |
|---|---|
| Time | 2–3 h |
| People | 2 |
| Tools | Allen keys (included), Phillips screwdriver |
| Size | 90x200 cm |
| Official manual | AA-1785340-10 |
| IKEA article number | 902.994.49 (dark grey) |
| Pieces in the box | 112 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Leg (numbered 1–4) | 4 | |
| Flat end bar | 6 | |
| Plain long rail | 2 | |
| Rail 3 (two notches) | 1 | |
| Rail 4 (one notch) | 1 | |
| Top rail | 1 | |
| Centre post | 1 | |
| Bent guard-rail tube | 2 | |
| Short rod | 2 | |
| Long rod | 2 | |
| Slat | 7 | |
| Ladder | 1 | |
| Ladder bracket | 2 | |
| Guard fabric | 1 | |
| Base fabric | 1 | |
| Connector 100014 + sleeve | 106986 | 40 |
| Bolt | 147722 | 3 |
| Bolt | 117444 | 1 |
| Bolt | 105102 | 4 |
| Sleeve nut | 100602 | 2 |
| Screw | 105892 | 14 |
| End cap | 144549 | 4 |
| Dome cap | 147909 | 2 |
| Anti-slip strip | 121108 | 4 |
| Wall strap | 130852 | 2 |
| Allen key | 100001 | 1 |
| Allen key | 100002 | 1 |
Steps
- Lay out the left end — Lay legs 4 and 3 side by side on the floor (leg 4 at the back), the big holes facing outwards, and put two flat end bars between them near the bottom ends. Check: Check the numbers on the legs and that each bar end has its bracket the right way round, as in the manual.
- Fix the end bars — Screw each threaded stud 100014 halfway into a sleeve 106986 (all 40 connectors). Fix each bar end with 2 connectors through the leg from the outside: 8 in all. Check: Only hand-tight for now: do not use the Allen key yet. All connectors are tightened in step 27.
- Caps on the feet — Press an end cap 144549 into the bottom end of each leg.
- Lay out the right end — Lay legs 1 and 2 down the same way (leg 1 at the back) with the other two flat end bars between them near the bottom ends.
- Fix the end bars — Fix each bar end with 2 connectors through the leg from the outside, as on the first end: 8 connectors, hand-tight. Check: Do not use the Allen key yet.
- Caps on the feet — Press an end cap 144549 into the bottom end of both legs.
- Stand both ends up — With a helper, stand both ends upright on their feet, the ends facing each other about 2 m apart: legs 4 and 1 at the back, legs 3 and 2 at the front.
- Lower back rail — Put one of the plain long rails between the back legs 4 and 1, at the holes level with the upper end bars. Fix each end with 2 connectors from the outside of the leg. Check: Use a plain rail here, not rail 3 or rail 4 (the ones with notches and numbers). Hand-tight only.
- Upper back rail — Fix the second plain rail between the back legs at the next holes up, with 2 connectors from the outside at each end. Check: Hand-tight only.
- Rail 4 into the guard fabric — Spread the guard fabric on the floor, inside up, both ends folded in. Slide rail 4 (one notch in the middle) into the bottom sleeve of the long side from the left, notch towards the top edge, number 4 at the left end. Check: The IKEA label is on the right-hand end of the fabric.
- Centre post — Push the short centre post down the pocket in the middle of the fabric into the notch of rail 4. Fix it from below, through the rail, with bolt 147722 and the long Allen key 100001.
- Top rail — Slide the long top rail into the top sleeve from the left, so the top end of the centre post goes into the holes in the middle of the rail.
- Bolt the top rail to the centre post — Screw bolt 117444 down through the top rail into the centre post with Allen key 100002. Check: Use the short bolt 117444 here, not a connector. The ends of the top rail and rail 4 must line up.
- Guard onto the back legs — With a helper, lift the guard over the frame and lower its long side between the two back legs, so the corner pockets slide down over the leg tops. The ends hang loose for now.
- Fix the back of the guard — At each back leg, fix the top rail with 1 connector and rail 4 with 2 connectors, all from the outside of the leg. Check: Hand-tight only.
- Right end of the guard — Slide a flat end bar into the bottom sleeve of the right-hand end of the fabric (the end with the IKEA label), then bring that end round to the front right leg.
- Rod in the top of the right end — Push a short rod through the top sleeve of the right end from the front and press its ends into the small holes at the top of the two right legs.
- Fix the right end bar — Fix the flat bar in the fabric with one connector through each right leg, from the back and from the front. Check: Hand-tight only.
- Left end of the guard — Bring the left end of the fabric part of the way round towards the front left leg. From its front end, slide a short rod into its top sleeve and a flat end bar into its bottom sleeve.
- Fix the left end — Bring the end fully round to the front left leg and press the rod ends into the holes at the top of the left legs. Fix the flat bar with one connector through each left leg from the outside. Check: Hand-tight only.
- Feed in rail 3 — Bring the two front flaps of the fabric round to the front. Feed rail 3 (two notches) in along the front from the right, notches up and the end marked 3 leading, through the bottom sleeves of the flaps.
- Push rail 3 through — Push rail 3 on through both front sleeves until its ends meet the front legs at bed height, the end marked 3 at leg 3.
- Fix rail 3 — Fix each end of rail 3 to its front leg with 2 connectors from the outside. The number 3 on the rail must sit next to the 3 on the leg. Check: Hand-tight only.
- Left guard-rail tube — Slide the long arm of a bent guard-rail tube into the top sleeve of the left flap until its end goes into the hole at the top of leg 3. Pull the fabric end over the bend and down the short leg, and set the leg in the left notch of rail 3.
- Right guard-rail tube — Do the same with the second tube on the right: long arm into the top sleeve of the right flap and into leg 2, fabric over the bend, leg in the right notch of rail 3.
- Fix the tubes at the legs — Fix the end of each guard-rail tube with one connector through the top of its front leg, from the outside. Check: Hand-tight only.
- Fix the tube legs from below — From underneath, screw a bolt 147722 up through rail 3 into each guard-rail tube leg with the long Allen key 100001.
- Tighten all connectors — Now tighten all 40 connectors firmly with Allen key 100002, at every leg: shown here at the front left leg. Check: Check them again after a few weeks and tighten if needed.
- Slats into the base — Lay the mesh base flat on the floor with the arrow label facing up. Push the 7 slats into its pockets, tabs standing up at both ends.
- Long rods in the side sleeves — Slide a long thin rod into the sleeve along each long side of the base, then fold the end of the sleeve closed over it.
- Tip the bed onto its back — With a helper, carefully tip the bed over backwards so it lies on its back. Hook the two ladder brackets over rail 3 in the opening between the front flaps.
- Base into the bed — Lift the base over the bed, stand it on its long edge at the top end and push it in through the guard until it sits against rails 3 and 4, slat tabs facing up.
- Screw the base to the rails — Screw each slat tab to the rail with a screw 105892 from inside the bed: 7 along rail 3 and 7 along rail 4.
- Caps on the ladder feet — Lay the ladder down and press a dome cap 147909 into the bottom end of each stile.
- Stand the bed up, hang the ladder — Tip the bed back onto its feet. Lift the ladder and slide the tops of its stiles up into the two brackets. Fix each stile with a bolt 105102 using the long Allen key 100001.
- Bolt the brackets to rail 3 — At each bracket, put a bolt 105102 through the hook and rail 3 from the front and a sleeve nut 100602 from inside the bed. Tighten with Allen key 100001 at the front while holding the nut with key 100002.
- Anti-slip strips on the rungs — Peel the backing off the anti-slip strips 121108 and press one firmly onto the top of each ladder rung.
- Optional: wall straps on the back legs — If the bed stands against a wall, fix it there. Put a wall strap 130852 round each back leg, just under the guard, its flat end towards the wall. Check: The manual also shows the straps on the two legs of one end, for a bed with its end against the wall.
- Optional: screw the straps to the wall — Push the bed against the wall and screw each strap to it. Use screws and plugs that suit your wall (not included).
- Done! — Your TUFFING loft bed is assembled. Use a 90×200 cm mattress no more than 15 cm thick, so the guard stays high enough above it. Max load 100 kg.
TUFFING loft bed frame: questions and answers
How long does it take to assemble the IKEA TUFFING loft bed frame?
About 2–3 h for 2 people, working through the 40 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the TUFFING loft bed frame?
Allen keys (included), Phillips screwdriver. Already in the box: Allen keys.
Can one person assemble the TUFFING loft bed frame?
It is planned as a 2-person build. One person can do most of it, but get help for steps 14, 31 and 32, where the furniture is lifted or turned.
What size is the TUFFING loft bed frame once assembled?
90x200 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.
How many screws and fittings come with the TUFFING loft bed frame?
76 fittings of 10 kinds, the most numerous being 40 × connector 100014 + sleeve, 14 × screw, 4 × bolt. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA TUFFING loft bed frame assembly instructions PDF?
The official PDF is manual AA-1785340-10, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 902.994.49 (dark grey); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-1785340-10. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example connector 100014). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA TUFFING bunk bed frame assembly instructions
- IKEA MALM bed frame (high, Queen) assembly instructions
- IKEA HEMNES day-bed frame with 3 drawers assembly instructions
- IKEA BRIMNES day-bed frame with 2 drawers assembly instructions
- IKEA MYDAL bunk bed frame assembly instructions
- IKEA SMÅSTAD loft bed frame w desk and storage assembly instructions
- IKEA VITVAL loft bed frame assembly instructions
- IKEA VITVAL bunk bed frame assembly instructions
All IKEA TUFFING assembly guides · All beds assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained