IKEA TUFFING bunk bed frame assembly instructions
How to assemble the IKEA TUFFING bunk bed frame, step by step: 37 animated steps built from the official manual, about 1.5–2 h for 2 people, with Allen keys (included), Phillips screwdriver.
Low dark grey steel-tube bunk bed with a fabric guard round the top bunk, a fabric end panel below, mesh slatted bases and a hook-on ladder. Size: 90x200 cm. About 1.5–2 h, 2 people. Tools: Allen keys (included), Phillips screwdriver.
Based on the official IKEA manual AA-1627840-11 (PDF). Guide updated .
| Steps | 37 |
|---|---|
| Time | 1.5–2 h |
| People | 2 |
| Tools | Allen keys (included), Phillips screwdriver |
| Size | 90x200 cm |
| Official manual | AA-1627840-11 |
| IKEA article number | 002.392.33 (dark grey) |
| Pieces in the box | 115 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Leg post | 4 | |
| Bed rail (marked 1–4) | 4 | |
| Flat end bar | 4 | |
| Short rod | 3 | |
| Long rod | 4 | |
| Top rail | 1 | |
| Centre post | 1 | |
| Bent guard-rail tube | 2 | |
| Slat | 14 | |
| Ladder | 1 | |
| Lower end panel (fabric) | 1 | |
| Guard fabric | 1 | |
| Base fabric | 2 | |
| Connector 100014 + sleeve | 106986 | 28 |
| Bolt | 147722 | 3 |
| Bolt | 117444 | 1 |
| Bolt | 100165 | 2 |
| Connector nut | 100673 | 2 |
| Screw | 105892 | 28 |
| End cap | 144549 | 4 |
| Anti-slip strip | 121108 | 2 |
| Allen key | 100001 | 1 |
| Allen key | 100002 | 2 |
Steps
- Bar and rod into the lower end panel — Lay the small fabric end panel flat. Slide a flat end bar into its wide bottom sleeve and a short rod into the narrow top sleeve.
- Slide the panel onto two legs — Lay two legs side by side: the one with holes marked 1 and 3 at the front, the one marked 2 and 4 at the back, labels facing up. Slide the panel's side sleeves onto them so it sits at the bottom end, next to labels 1 and 2. Check: The bottom end of a leg is the end nearest the holes marked 1 or 2.
- Fix the end bar — First screw a threaded stud 100014 halfway into each sleeve 106986 (all 28 connectors). Fix the flat bar with one connector through each leg from the outside. The ends of the rod push into the small holes in the legs. Check: Only hand-tight for now: do not use the Allen key yet. All connectors are tightened in step 29.
- Caps on the feet — Press an end cap 144549 into the bottom end of each leg.
- The other end: two legs and a bar — Lay the other two legs down the same way (1/3 at the front, 2/4 at the back) and put a flat end bar between them at the bottom end. This end has no fabric panel.
- Fix the bar — Fix the bar with one connector through each leg from the outside, hand-tight. Check: Do not use the Allen key yet.
- Caps on the feet — Press an end cap 144549 into the bottom end of both legs.
- Stand up the panel end, rails 1 and 2 — Stand the end with the fabric panel upright. Put rail 1 (with the two large holes) against the front leg at the holes marked 1, and rail 2 against the back leg at the holes marked 2, number labels at this end. Fix each rail with 2 connectors from the outside. Check: Match the numbers: each rail goes to the holes with its own number. The fabric panel may go at either end of the bed.
- Add the second end — Stand the second end up and push its legs against the free ends of rails 1 and 2, at the holes marked 1 and 2. Fix each rail end with 2 connectors from the outside.
- Rail 4 into the guard fabric — Spread the large guard fabric on the floor, inside up: the long side in the middle, both ends folded in over it. Slide rail 4 into the bottom sleeve of the long side from the left, centre notch towards the top edge. The IKEA label ends up at the right.
- Centre post — Push the short centre post through the opening in the middle of the top sleeve, down the pocket and into the notch of rail 4. Fix it from below, through the rail, with bolt 147722 and the long Allen key 100001.
- Top rail — Slide the long top rail into the top sleeve from the left, so the top end of the centre post goes into the holes in the middle of the rail.
- Bolt the top rail to the centre post — Screw bolt 117444 down through the top rail into the centre post with Allen key 100002. Check: Use the short bolt 117444 here, not a connector. Line the ends of the fabric up with the ends of the rails.
- Guard onto the back legs — With a helper, lift the guard, stand it up and lower its long side between the two back legs from above, so the corner pockets slide over the leg tops. The two ends stay loose for now.
- Fix the back of the guard — At each back leg, fix the top rail with 1 connector and rail 4 with 2 connectors, all from the outside of the leg. Check: Hand-tight only.
- Right end of the guard — Slide a flat end bar into the bottom sleeve of the right-hand end of the fabric (the end with the IKEA label), then bring that end round to the front right leg.
- Rod in the top of the right end — Thread a short rod through the top sleeve of the right end and press its ends into the small holes at the top of the two right legs.
- Fix the right end bar — Fix the flat bar with one connector through each right leg, from the back and from the front. Check: Hand-tight only.
- Left end of the guard — Slide a short rod into the top sleeve and a flat end bar into the bottom sleeve of the left end, then bring the end round to the front left leg.
- Fix the left end — Press the rod ends into the holes at the top of the left legs, and fix the flat bar with one connector through each left leg from the outside. Check: Hand-tight only.
- Feed rail 3 along the front — Bring the two front flaps of the fabric round to the front. Feed rail 3 (the one with two notches) in along the front from the right, notches up and the end marked 3 leading.
- Rail 3 into the front sleeves — Push rail 3 all the way into the bottom sleeves of both front flaps, until its ends meet the front legs at the holes marked 3.
- Fix rail 3 — Fix each end of rail 3 to its front leg with 2 connectors from the outside. Check: Hand-tight only.
- Left guard-rail tube — Slide the long arm of a bent guard-rail tube into the top sleeve of the left front flap until its end goes into the hole at the top of the front left leg. Pull the end of the fabric over the bend and down the short leg, and set the leg in the left notch of rail 3.
- Right guard-rail tube — Do the same with the second tube on the right: long arm into the top sleeve of the right flap and into the front right leg, fabric over the bend, leg in the right notch of rail 3.
- Fix the tubes at the legs — Fix the end of each guard-rail tube with one connector through the top of its front leg, from the outside. Check: Hand-tight only.
- Fix the tube legs from below — From underneath, screw a bolt 147722 up through rail 3 into each guard-rail tube leg with the long Allen key 100001.
- Ladder — Hook the ladder over rail 3 between the two guard-rail tubes. At the bottom, fix each ladder foot to rail 1: connector nut 100673 from inside the bed, bolt 100165 from the front. Hold one with an Allen key 100002 while you turn the other with the second key.
- Tighten all connectors — Now tighten all 28 connectors firmly with Allen key 100002, at every leg: shown here at the front left leg. Check: Check them again after a few weeks and tighten if needed.
- Slats into both bases — Lay each mesh base flat with the arrow label facing up. Push 7 slats into the pockets of each base, with the tabs standing up at both ends.
- Long rods in the side sleeves — Slide a long thin rod into the sleeve along each long side of both bases, then fold the sleeve closed over it.
- Lower base — Lift one base over the bed and lower it through the top frame down onto the lower bed, so its slat tabs stand against the inside of rails 1 and 2.
- Screw the lower base — Screw each slat tab to the rail with a screw 105892 from inside the bed: 7 along the front rail and 7 along the back rail.
- Upper base — Lift the second base over the guard and lower it onto the upper bed, slat tabs against the inside of rails 3 and 4.
- Screw the upper base — Screw each slat tab of the upper base to the rail with a screw 105892 from inside the bed: 7 at the front, 7 at the back.
- Anti-slip strips on the ladder — Peel the backing off the two anti-slip strips 121108 and press one firmly onto the top of each ladder rung.
- Done! — Your TUFFING bunk bed is assembled. Use 90×200 cm mattresses no more than 11 cm thick, so the guard stays high enough above the top mattress. Max 100 kg per bed.
TUFFING bunk bed frame: questions and answers
How long does it take to assemble the IKEA TUFFING bunk bed frame?
About 1.5–2 h for 2 people, working through the 37 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the TUFFING bunk bed frame?
Allen keys (included), Phillips screwdriver. Already in the box: Allen keys.
Can one person assemble the TUFFING bunk bed frame?
It is planned as a 2-person build. One person can do most of it, but get help for steps 9, 14 and 32, where the furniture is lifted or turned.
What size is the TUFFING bunk bed frame once assembled?
90x200 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.
How many screws and fittings come with the TUFFING bunk bed frame?
70 fittings of 8 kinds, the most numerous being 28 × connector 100014 + sleeve, 28 × screw, 4 × end cap. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA TUFFING bunk bed frame assembly instructions PDF?
The official PDF is manual AA-1627840-11, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 002.392.33 (dark grey); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-1627840-11. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example connector 100014). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA TUFFING loft bed frame assembly instructions
- IKEA MALM bed frame (high, Queen) assembly instructions
- IKEA HEMNES day-bed frame with 3 drawers assembly instructions
- IKEA BRIMNES day-bed frame with 2 drawers assembly instructions
- IKEA MYDAL bunk bed frame assembly instructions
- IKEA SMÅSTAD loft bed frame w desk and storage assembly instructions
- IKEA VITVAL loft bed frame assembly instructions
- IKEA VITVAL bunk bed frame assembly instructions
All IKEA TUFFING assembly guides · All beds assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained