Step by StepAssembly Find your furniture

IKEA SMÅSTAD loft bed frame w desk and storage assembly instructions

How to assemble the IKEA SMÅSTAD loft bed frame w desk and storage, step by step: 40 animated steps built from the official manual, about 3–4 h for 2 people, with Allen keys and ring wrench (included), cross-head screwdriver, flat-blade screwdriver.

IKEA SMÅSTAD loft bed frame w desk and storage, assembled

White loft bed on a two-part end panel and a storage unit with open shelves, with a ladder at the storage end and room for a desk underneath. Size: 90x200 cm. About 3–4 h, 2 people. Tools: Allen keys and ring wrench (included), Cross-head screwdriver, Flat-blade screwdriver.

Based on the official IKEA manual AA-2200882-8 (PDF). Guide updated .

SMÅSTAD loft bed frame w desk and storage: quick facts
Steps40
Time3–4 h
People2
ToolsAllen keys and ring wrench (included), Cross-head screwdriver, Flat-blade screwdriver
Size90x200 cm
Official manualAA-2200882-8
IKEA article number504.540.36 (white)
Pieces in the box179

In the box

PartPart numberQuantity
Gable half2
Long back panel1
Front rail1
Front guard panel1
End panel1
Cross support2
Bed board6
Back rail1
Ladder rail2
Ladder rung5
Metal angle1520542
Storage unit (own manual)1
Cam pin1234912
Screw10021816
Bolt1051053
Bolt10510016
Cam bolt1146138
Cam1928004
Cam1134344
Dowel10135819
Dowel1013521
Sleeve nut10060016
Screw11689418
Cam1146702
Cover cap1506262
Bolt1052378
Cross dowel1284378
Nut1007108
Floor glide1060436
Anti-slip strip1211085
Grip insert1907302
Grip insert1907292
Ring wrench1134531
Allen key1000921
Allen key1000021
Allen key1000491

Steps

  1. Gable: cam pins in one half — Work on a rug. Lay one half of the tall end panel flat and stand the other half on its long edge, the edge with the extra holes up. Screw the 2 cam pins 123491 into the two outer holes of that edge and tighten them with the ring wrench 113453. Check: The two halves join along their long edges to make the tall end panel (gable) at the desk end.
  2. Gable: 5 dowels — Push 5 dowels 101358 into the remaining holes of the same edge, between and beyond the cam pins. Check: Use the dowels 101358 here, not the slightly different 101352.
  3. Gable: cams, lay the half down — Press the 2 large cams 114670 into the round holes of the flat half, near its long edge, with their openings facing that edge. Then lay the half with the pins down flat beside it, pins pointing at the cam half. Check: Check that each cam opening faces the edge, so the cam pin can slide into it.
  4. Gable: join the halves — Push the two halves together so the pins and dowels go into the other half. Turn each cam clockwise with the Allen key 100049 until the halves are pulled tight together.
  5. Gable: cover caps — Press a cover cap 150626 onto each of the 2 cams. The tall end panel is ready.
  6. Metal angles on the long rails — Lay the long back panel and the narrow front rail flat, inside face up. Place a metal angle on each along its bottom edge: the screw holes line up with the small pre-drilled holes in the panel. Check: Check the drawings: the angle's flat flange sits on the panel, the other flange stands up along the edge.
  7. Fix the angles: first screws — Fix each angle with 1 screw 116894 in its middle hole, turned in with a cross-head screwdriver. This holds it in place for the rest. Check: Use a hand screwdriver, not a drill: the screws strip easily.
  8. Fix the angles: 16 screws — Screw the angles down with the remaining 16 screws 116894, 8 in each angle, using the screwdriver. Check: No drill. Tighten until the head sits flat on the angle.
  9. Back panel to the gable — Stand the gable on its top end. Stand the long back panel upside down against it. Push a nut 100710 into each of 2 cross dowels 128437 and drop them into the panel, slot lined up with a screwdriver. Fix with 2 bolts 105237 through the gable, Allen key 100092. Check: Use the long bolts 105237 here, not the screws 100218.
  10. Tip over, cross supports — Tip the gable and back panel over so the back panel lies flat. Stand the 2 cross supports on the angle near the far end. Fix each with a bolt 105100 through the support and angle into a sleeve nut 100600, using Allen keys 100092 and 100002.
  11. Front rail to the gable — Lift the front rail, angle inwards, onto the top of the cross supports and slide it along until its end meets the gable. Drop 2 cross dowels 128437 with nuts 100710 into it and fix it with 2 bolts 105237 through the gable. Check: Long bolts 105237 again, not the screws 100218.
  12. Cross supports to the front rail — Fix the other end of each cross support to the front rail's angle with a bolt 105100 and a sleeve nut 100600, as in step 10.
  13. Locating dowel — Push 1 dowel 101352 into the hole in the bottom edge of the front rail, near its free end. It will locate the rail on the storage unit. Check: This is the slightly different dowel 101352, not 101358.
  14. Floor glides on the gable — Press 4 floor glides 106043 into the pairs of holes in the bottom edge of the gable.
  15. Cam bolts in the storage unit — Take the storage unit built with its own SMÅSTAD manual and stand it up, open side to the right. Screw 4 cam bolts 114613 into the holes in its top: 2 along the open side, 2 along the back edge.
  16. End panel on the storage unit — Lower the end panel onto the top of the storage unit, along the open side, so the 2 cam bolts there go into the holes in its bottom edge.
  17. Lock the end panel — Push 2 cams 192800 into the holes on the inside of the end panel and turn them clockwise with a screwdriver until they lock onto the cam bolts. Check: Use the cams 192800 here, not 113434.
  18. Stand the frame on the storage unit — With a helper, stand the frame up. Lower the far ends of the long rails onto the storage unit, inside the end panel: the back panel onto the 2 cam bolts, the front rail's dowel into its hole, the gable on its glides. Check: Two people. Lower it straight: the cam bolts break if the frame lands on them at an angle.
  19. Lock the back panel — Push 2 cams 113434 into the holes near the bottom of the back panel, above the storage unit, and turn them clockwise with a screwdriver. Check: Use the cams 113434 here, not 192800.
  20. Bolt the end panel to the long rails — Push nuts 100710 into 4 cross dowels 128437 and drop 2 into the back panel and 2 into the front rail, near the end panel. Fix both rails with 4 bolts 105237 through the end panel, using Allen key 100092.
  21. Cam bolts for the back rail — Screw 2 cam bolts 114613 into the holes in the back edge of the storage unit, on the desk side, at desk height.
  22. Back rail in — Fit one end of the back rail onto the 2 cam bolts, then swing its other end in against the inside of the gable.
  23. Screw the back rail to the gable — Fix the back rail with 2 screws 100218 through the outside of the gable, tightened with Allen key 100092. Check: Use the screws 100218 here.
  24. Lock the back rail — Push 2 cams 113434 into the holes in the back rail beside the storage unit and turn them clockwise with a screwdriver until they lock onto the cam bolts. Check: Cams 113434 here, not 192800.
  25. Front guard panel — Hold the front guard panel against the outside of the front rail, between the gable and the ladder opening. Fix it with 3 bolts 105105 from inside the frame, through the front rail, using Allen key 100092.
  26. Screw the guard panel to the gable — Fix the guard panel's end with 2 screws 100218 through the outside of the gable, tightened with Allen key 100092.
  27. Bed boards — Lay the 6 bed boards across the frame between the gable and the cross supports, resting on the metal angles, holes over the holes in the angles.
  28. Bed boards: sleeve nuts from below — From under the bed, push a sleeve nut 100600 up through each hole in the angles into the boards: 12 in all, 2 per board. Hold them with Allen key 100002.
  29. Bed boards: 12 bolts — From above, screw a bolt 105100 through each board end into its sleeve nut and tighten with Allen key 100092 while key 100002 holds the nut below.
  30. Ladder: 14 dowels — Lay the two ladder rails flat, inside faces up, rounded ends at the same end. Push 14 dowels 101358 into the holes, 7 in each rail. Check: Push them in by hand; do not hammer them.
  31. Ladder: rungs and the first rail — Stand the 5 rungs on the dowels of one rail. Turn the other rail over onto them, then fix it to rungs 1, 3 and 5 with 3 screws 100218, using Allen key 100092.
  32. Ladder: cam bolts — Screw 2 cam bolts 114613 into the edge of the rail you just fixed, near its rounded end. Then turn the ladder over.
  33. Ladder: second rail — Fix the second rail to rungs 1, 3 and 5 with 3 screws 100218, using Allen key 100092.
  34. Ladder: floor glides — Lay the ladder flat and press a floor glide 106043 into the pair of holes in the bottom end of each rail.
  35. Ladder: hand-grip inserts — Fit the hand-grip inserts in the slot of each rail: push a 190730 in from one side, then press a 190729 in from the other side until it clicks. Check: The two insert halves are different: one from each side, as drawn.
  36. Ladder in place — Stand the ladder up and push it against the front of the storage unit, right of the guard panel. Fix the left rail to the guard panel's end with 2 screws 100218, using Allen key 100092.
  37. Lock the ladder to the end panel — Push 2 cams 192800 into the holes on the inside of the end panel, next to the ladder, and turn them clockwise with a screwdriver until they lock onto the ladder's cam bolts. Check: Cams 192800 here, not 113434.
  38. Screw the ladder from inside the storage unit — From inside the storage unit's narrow shelf column, fix the ladder with 4 screws 100218 through the unit's side into the rails, 2 into each rail, using Allen key 100092.
  39. Anti-slip strips on the rungs — Peel the backing off the 5 anti-slip strips 121108 and press one onto the top of each rung, smoothing it from the middle outwards.
  40. Done! — The SMÅSTAD loft bed frame with storage is assembled. Use a 90×200 cm mattress no thicker than 20 cm so the guard rail stays high enough. Fit the desk under the bed with its own SMÅSTAD manual. Check the bolts regularly and tighten them when needed.

SMÅSTAD loft bed frame w desk and storage: questions and answers

How long does it take to assemble the IKEA SMÅSTAD loft bed frame w desk and storage?

About 3–4 h for 2 people, working through the 40 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the SMÅSTAD loft bed frame w desk and storage?

Allen keys and ring wrench (included), cross-head screwdriver, flat-blade screwdriver. Already in the box: Allen keys and ring wrench.

Can one person assemble the SMÅSTAD loft bed frame w desk and storage?

It is planned as a 2-person build. One person can do most of it, but get help for steps 10, 11 and 15, where the furniture is lifted or turned.

What size is the SMÅSTAD loft bed frame w desk and storage once assembled?

90x200 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the SMÅSTAD loft bed frame w desk and storage?

153 fittings of 22 kinds, the most numerous being 19 × dowel, 18 × screw, 16 × screw. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA SMÅSTAD loft bed frame w desk and storage assembly instructions PDF?

The official PDF is manual AA-2200882-8, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 504.540.36 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2200882-8. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example metal angle 152054). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All beds assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained