IKEA VITVAL bunk bed frame assembly instructions
How to assemble the IKEA VITVAL bunk bed frame, step by step: 46 animated steps built from the official manual, about 3–4 h for 2 people, with Allen keys + handle (included), Phillips screwdriver, flat-blade screwdriver, hammer.
White steel bunk bed with light grey fabric guards, two roll-out slatted bases and a straight ladder near one end of the long side. Size: 90x200 cm. About 3–4 h, 2 people. Tools: Allen keys + handle (included), Phillips screwdriver, Flat-blade screwdriver, Hammer.
Based on the official IKEA manual AA-2136284-5 (PDF). Guide updated .
| Steps | 46 |
|---|---|
| Time | 3–4 h |
| People | 2 |
| Tools | Allen keys + handle (included), Phillips screwdriver, Flat-blade screwdriver, Hammer |
| Size | 90x200 cm |
| Official manual | AA-2136284-5 |
| IKEA article number | 804.112.72 (white light grey) |
| Pieces in the box | 190 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Leg, 154 cm (front) | 2 | |
| Leg, 162 cm (back) | 2 | |
| End bar | 1 | |
| Guard fabric: end | 3 | |
| Guard fabric: back (tall) | 2 | |
| Guard fabric: front | 1 | |
| End guard bottom rail | 3 | |
| Long rail (with holes) | 4 | |
| Upright, short | 9 | |
| Upright, long | 6 | |
| Top rod: end | 3 | |
| Top rod: back (200 cm) | 2 | |
| Top rod: front (159 cm) | 1 | |
| Slat support rail | 4 | |
| Ladder post | 1 | |
| Ladder stile | 1 | |
| Rung | 2 | |
| Ladder bracket | 2 | |
| Slatted base | 2 | |
| Bolt | 10004072 | 39 |
| Screw | 10003444 | 30 |
| Screw | 120925 | 44 |
| Sleeve nut | 100602 | 16 |
| Screw | 117359 | 1 |
| Hole cap | 10004760 | 1 |
| Screw | 118832 | 1 |
| Pin | 100644 | 1 |
| Top cap | 10129455 | 1 |
| Anti-slip strip | 121108 | 2 |
| Allen key | 100092 | 1 |
| Allen key | 108490 | 1 |
| Key handle | 121030 | 1 |
Steps
- End guards: bottom rails — Build the three small end guards the same way. Lay a small fabric panel flat and slide a short bottom rail into the sleeve along its bottom edge. Check: Use the short bottom rails here, not the long ones.
- Short uprights — Push a short upright down each side sleeve until it stands on the bottom rail, then tuck the fabric edge round the rail. Do the same on the other two guards. Check: Use short uprights here, not the long ones.
- Top rods — Slide a short top rod through the top sleeve of each guard so it rests on the uprights, the countersunk holes facing up. Check: Use the three shortest rods.
- Screw the end guards together — Fix each upright with a countersunk screw 10003444 down through the top rod and one up through the bottom rail, in the order 1-4, using Allen key 100092. 4 screws per guard, 12 in all. Check: The screw heads must sit flush in their countersinks.
- Lay out the left end — Lay one 154 cm leg (slot at the top) and one 162 cm leg on the floor. Put two end guards between them: one at the top ends, the other lower down. Check: The two legs of this end have different lengths: the long one is the back leg. Both feet go at the bottom.
- Bolt the left end — Fix the guards with 7 bolts 10004072 through the legs: the upper rail, lower rod and lower rail at the short leg, the rod and rail of both guards at the long leg. Tighten with Allen key 100092. Check: The upper rod at the short leg is fixed from inside the leg in the next step. Bolt heads must sit flat.
- Lock the rod inside the short leg — Drop screw 117359 into the slotted top of the short leg and screw it into the end of the upper guard rod with Allen key 108490 in the key handle 121030 (slot 5). Then knock the top cap 10129455 into the leg with a wood block and a hammer.
- Build the right end — Lay out the other 154 cm leg and 162 cm leg with the plain end bar between them, near the feet. Fix the bar with a bolt 10004072 through each leg, Allen key 100092. Check: Check the hole pattern on the legs against the drawing before bolting.
- Back guards: bottom rails — Build both large back guards the same way. Lay a large fabric panel flat and slide a long rail with holes into its bottom sleeve from the left, holes facing the inside. Check: Check each rail is the right way round: its notch and holes must match the drawing.
- Long uprights — Push three long uprights down the sleeves of each back guard until they stand on the rail: left (1), right (2), then the middle (3). Tuck the fabric edges round the rail. Check: Use the long uprights here.
- Back top rods — Slide a 200 cm rod through the top sleeve of each back guard from the left, countersunk holes facing up. Check: Use the two longest rods.
- Screw the back guards together — Fix the uprights of each back guard with 6 countersunk screws 10003444 in the order 1-6: three down through the top rod, three up through the rail. Allen key 100092. 12 screws in all.
- Slat rail on the first back guard — Set a slat support rail against the inside of the bottom rail, the notches as shown, and fix it with 6 screws 120925 in the order 1-6. Use Allen key 100092 in the key handle 121030 (slot 4). Check: Check the notch at the right-hand end matches the drawing.
- Slat rail on the second back guard — Fix the second slat support rail to the other back guard the same way: 6 screws 120925 in the order 1-6.
- Front guard: bottom rail — Lay the front fabric panel flat. Slide the third long rail with holes into its bottom sleeve from the left: the rail sticks out past the fabric on the right. Check: Check the rail is the right way round: its notch and holes must match the drawing.
- Short uprights — Push three short uprights down the sleeves until they stand on the rail: middle (1), left (2), right (3). Tuck the fabric edges round the rail.
- Front top rod — Slide the 159 cm rod into the top sleeve from the right, countersunk holes facing up.
- Screw the front guard together — Fix the uprights with 6 countersunk screws 10003444 in the order 1-6: three down through the rod, three up through the rail. Allen key 100092.
- Bracket on the ladder post — Lay the short ladder post down past the rail end, its hole at the top end. Put the bracket with the deep waist against the inner side of its bottom end and fix it with a screw 120925, Allen key 100092. Check: There are two brackets: use the one with the deep waist here.
- Post onto the top rod — Slide the post in from the right until it meets the end of the top rod, the bracket over the rail below it. Fix it with a bolt 10004072 through the post into the rod end, Allen key 100092.
- Slat rail on the front guard — Fix the third slat support rail along the inside of the front rail, its notch at the ladder bracket, with 6 screws 120925 in the order 1-6. Allen key 100092 in the handle 121030.
- Lower front rail — Lay the last long rail with holes flat and fix the last slat support rail along its inside with 6 screws 120925, Allen key 100092 in the handle 121030. Check: Check the rail and the slat rail are the right way round: the holes at the ends match the drawing.
- Stand both ends up — With a helper, stand both ends upright about 2 m apart, the long legs at the back and the short legs at the front.
- Lift in the lower back guard — Stand one back guard up and carry it between the two long back legs, at the bottom, its slat rail facing the inside.
- Bolt the lower back guard — Fix the guard with 6 bolts 10004072 from the outside of the long legs: the top rod and the rail (2) at each leg. Allen key 100092.
- Lift in the front guard — With a helper, stand the front guard up and lift it between the two short front legs, the post towards the right. The rail ends meet the legs at the upper bed height.
- Bolt the front guard — Fix the front guard with 5 bolts 10004072 from the outside of the legs: the top rod and the rail (2) at the left leg, the rail (2) at the right leg.
- Lower front rail — Stand the lower front rail on its edge, slat rail facing the inside, and push it in between the two front legs at the height of the lower back rail. Fix it with 2 bolts 10004072 through each leg.
- Lift in the upper back guard — With a helper, stand the second back guard up, lift it over the front guard and lower it between the two long back legs at the top. Check: Lift it high enough to clear the front guard and the leg tops.
- Bolt the upper back guard — Fix the upper back guard with 6 bolts 10004072 from the outside of the long legs: the top rod and the rail (2) at each leg.
- Ladder: rungs on the stile — Lay the ladder stile on the floor, slotted end towards you, and put the two rungs against it. Fix each rung with a bolt 10004072 through the stile, Allen key 100092.
- Carry the ladder to the bed — Stand the ladder up and carry it to the front of the bed, slotted foot down, leaning the top slightly away from the bed.
- Fit the ladder — Set the slot in the ladder foot on the lower front rail just left of the post, swing the top in under the post, then slide the ladder right until the rungs touch the front right leg. Check: The slot at the foot must sit over the rail.
- Bolt the rungs to the leg — Fix the rungs to the front right leg with 2 bolts 10004072 from the outside, Allen key 100092.
- Second ladder bracket — Put the bracket with the shallow waist on the outside, over the post, the rail and the top of the stile. Fix it with 2 screws 120925 from the front (post, stile) and 1 screw from behind into the stile. Allen key 100092.
- Anti-slip strips — Peel the backing off the 2 anti-slip strips 121108 and press one firmly onto the top of each rung.
- Upper slatted base — With a helper, lift a slatted base to the upper bed at the right-hand end, slats curving up, and slide it in along the slat rails until its strap ends go into the slots at the left legs. Check: The slats must curve upwards, and the base must stay straight as it goes in.
- Lift in the last end guard — With a helper, stand the last end guard up, carry it to the right-hand end and slide it in between the two right legs at the top.
- Bolt the last end guard — Fix the guard with 4 bolts 10004072: the top rod and the rail through the front leg and through the back leg.
- Hole cap — Close the spare hole in the upper front rail, between the post and the right leg, with the slotted cap 10004760: turn it in with a flat-blade screwdriver.
- Fix the upper slatted base — Fix the base straps to the slat rails with 8 screws 120925 from the top (Allen key 100092) into 8 sleeve nuts 100602 from below (Allen key 108490): 4 along the front and 4 along the back.
- Lower slatted base — Slide the second slatted base in from the right-hand end, slats curving up, just above the end bar. When it is in, let it down onto the slat rails and push it left until the strap ends go into the slots at the left legs. Check: The slats must curve upwards.
- Sleeve nuts under the lower base — Push 8 sleeve nuts 100602 up through the slat rails from below, 4 along the front and 4 along the back. Hold them with Allen key 108490.
- Screw the lower base down — Screw 8 screws 120925 from the top through the straps and the slat rails into the sleeve nuts, Allen key 100092.
- Close the spare leg hole — Push the pin 100644 into the spare hole in the back right leg from behind, at the height of the lower guard rods, and screw the screw 118832 into it from the inside with a Phillips screwdriver.
- Done! — Your VITVAL bunk bed is assembled. Go round once more and re-tighten every bolt and screw, and check them again after a few weeks. Use 90×200 cm mattresses no more than 13 cm thick so the guards stay high enough. Max 100 kg per bed.
VITVAL bunk bed frame: questions and answers
How long does it take to assemble the IKEA VITVAL bunk bed frame?
About 3–4 h for 2 people, working through the 46 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the VITVAL bunk bed frame?
Allen keys + handle (included), Phillips screwdriver, flat-blade screwdriver, hammer. Already in the box: Allen keys + handle.
Can one person assemble the VITVAL bunk bed frame?
It is planned as a 2-person build. One person can do most of it, but get help for steps 24, 26 and 29, where the furniture is lifted or turned.
What size is the VITVAL bunk bed frame once assembled?
90x200 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.
How many screws and fittings come with the VITVAL bunk bed frame?
137 fittings of 11 kinds, the most numerous being 44 × screw, 39 × bolt, 30 × screw. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA VITVAL bunk bed frame assembly instructions PDF?
The official PDF is manual AA-2136284-5, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 804.112.72 (white light grey); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2136284-5. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example bolt 10004072). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA VITVAL loft bed frame assembly instructions
- IKEA MALM bed frame (high, Queen) assembly instructions
- IKEA HEMNES day-bed frame with 3 drawers assembly instructions
- IKEA TUFFING bunk bed frame assembly instructions
- IKEA BRIMNES day-bed frame with 2 drawers assembly instructions
- IKEA MYDAL bunk bed frame assembly instructions
- IKEA SMÅSTAD loft bed frame w desk and storage assembly instructions
- IKEA TUFFING loft bed frame assembly instructions
All IKEA VITVAL assembly guides · All beds assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained