IKEA BRIMNES bedside table assembly instructions
How to assemble the IKEA BRIMNES bedside table (nightstand), step by step: 28 animated steps built from the official manual, about 1–1.5 hours for 1 person, with flat-blade screwdriver, Phillips screwdriver, hammer.
A small white BRIMNES bedside table: a cam-lock frame built lying down, a nailed-on back, an open shelf, and a drawer with a frosted-glass front on runners. Size: 39x41x53 cm. About 1–1.5 hours, 1 person. Tools: Flat-blade screwdriver, Phillips screwdriver, Hammer.
Based on the official IKEA manual AA-2523142-1 (PDF). Guide updated .
| Steps | 28 |
|---|---|
| Time | 1–1.5 hours |
| People | 1 |
| Tools | Flat-blade screwdriver, Phillips screwdriver, Hammer |
| Size | 39x41x53 cm |
| Official manual | AA-2523142-1 |
| IKEA article number | 102.349.42 (white) |
| Pieces in the box | 92 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Side panel | 2 | |
| Top | 1 | |
| Back rail | 1 | |
| Front rail (grooved) | 1 | |
| Back panel | 1 | |
| Shelf | 1 | |
| Drawer front (frosted glass) | 1 | |
| Drawer side | 2 | |
| Drawer back | 1 | |
| Drawer bottom | 1 | |
| Cam screw | 118331 | 12 |
| Wooden dowel | 101345 | 12 |
| Cam lock 117434/119030 | 8 | |
| Cam lock 118224/119030 | 4 | |
| Screw | 100365 | 8 |
| Drawer runner set 158933 (4 rails) | 1 | |
| Glide | 153548 | 4 |
| Shelf support 107519/107938 | 4 | |
| Nail holder | 105494 | 1 |
| Nails 101221 (bag) | 18 | |
| Expansion screw | 110519 | 4 |
| Bumpers 107091 (sheet of 2) | 1 | |
| Handle | 130509 | 1 |
| Screw | 109567 | 2 |
Steps
- Cam screws into the side panels — Lay both side panels on a soft surface with the inside facing up. Screw 2 cam screws 118331 into the small holes near the bottom end of each panel.
- Runners on the side panels — Lay a carcass runner along the bottom end of each side panel, wheel at the front edge, and fix it with 2 screws 100365. Check: The runners are marked L and R: the one marked R goes on the right-hand side panel.
- Rails onto the right side panel — Push 2 dowels 101345 into the right side panel and 1 into the free end of each rail. Stand the grey back rail and the grooved front rail on the panel, over the dowels and cam screws. Check: The rails have cam lock holes on one face: those face the bottom end of the panel.
- Lock the rails to the right side — Put a cam lock 117434 into the hole in each rail next to the side panel, and turn it clockwise with a flat screwdriver until it grips the cam screw.
- Left side panel on — Roll the frame onto its back so the front edges face up. Swing the left side panel up, inside facing in, and push it onto the free ends of the rails so the dowels and cam screws go into their holes.
- Lock the rails to the left side — Put a cam lock 117434 into each rail next to the left side panel and turn it clockwise to lock.
- Cam screws into the top — Lay the top upside down on a soft surface and screw 4 cam screws 118331 into the holes near its side edges.
- Fit the top — Push 4 dowels 101345 into the top edges of the side panels. Turn the top up and push it onto the frame, cam screws first, so its back edge is flush with the back edges of the sides. Check: Check the edges: the top must be flush with the frame at the back.
- Lock the top — Put 4 cam locks 117434 into the holes in the inside of the side panels, just under the top, and turn each one clockwise to lock.
- Glides under the side panels — Press 4 glides 153548 into the holes in the bottom edges of the side panels, 2 on each side.
- Turn it over, back panel on — Turn the frame over so it lies on its front. Lay the back panel on the back of the frame, the right way round so its edges line up with the frame. Check: The back panel is not quite square: turn it until its edges match the frame.
- The first nail — Push the back panel into the top right corner so its edges are flush with the top and the side. Hold a nail 101221 in the nail holder 105494 and hammer it in at that corner, then pull the holder away.
- Nail the other corners — Push the panel flush with the frame at the other top corner and nail it there, then square it up at the bottom right corner and nail it there too.
- Nail the back panel all round — Hammer in the other 15 nails 101221 through the holes along the top and both sides, using the nail holder.
- Stand it up, shelf supports — Stand the table up on its glides and turn it round so the front faces you. Push 4 shelf supports 107519 into the holes in the side panels, 2 on each side at the same height.
- Shelf — Lay the shelf on the 4 shelf supports.
- Dowels in the drawer sides — Now the drawer (bag 2). Lay the 2 drawer sides on a soft surface and push 2 dowels 101345 into the front end of each.
- Cam screws into the drawer front — Lay the drawer front face down and screw 4 cam screws 118331 into the small holes on the inside, 2 near each side.
- Drawer sides onto the front — Stand the drawer sides on the front, grooves facing in, and press them down onto the cam screws so the dowels go into their holes.
- Lock the drawer sides — Put 4 cam locks 118224 into the holes on the inside of the drawer sides, next to the front, and turn each one clockwise to lock.
- Slide in the drawer bottom — Slide the drawer bottom down into the grooves in the sides, from the open end, until it touches the front.
- Drawer back — Place the drawer back between the sides at the open end, on top of the drawer bottom, with its notches over the bottom.
- Fix the drawer back — Hammer 4 expansion screws 110519 through the holes in the drawer sides into the ends of the back, 2 on each side.
- Bumpers on the front — Stick the 2 bumpers 107091 on the inside of the drawer front, at the corners just outside the drawer sides.
- Runners on the drawer — Turn the drawer upside down on a table, with the front hanging over the edge. Press a drawer runner onto the bottom edge of each side, wheel at the back, and fix each one with 2 screws 100365. Check: The drawer runners are marked L and R as well.
- Handle — Turn the drawer the right way up. Hold the handle 130509 on the top band of the front and screw it on from the inside with 2 screws 109567.
- Put the drawer in — Hold the drawer in front of the lower opening, tilt the front up a little and set the drawer’s back wheels on the runners in the frame. Slide it in, lower the front and push it all the way home.
- Done! — Your BRIMNES bedside table is finished. Pull the drawer out by its handle; cables can run in through the gap under the back panel.
BRIMNES bedside table: questions and answers
How long does it take to assemble the IKEA BRIMNES bedside table?
About 1–1.5 hours for 1 person, working through the 28 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the BRIMNES bedside table?
Flat-blade screwdriver, Phillips screwdriver, hammer.
Can one person assemble the BRIMNES bedside table?
Yes, it is a one-person build.
What size is the BRIMNES bedside table once assembled?
39x41x53 cm, as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the BRIMNES bedside table?
60 fittings of 11 kinds, the most numerous being 12 × cam screw, 12 × wooden dowel, 8 × cam lock 117434/119030. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA BRIMNES bedside table assembly instructions PDF?
The official PDF is manual AA-2523142-1, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 102.349.42 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2523142-1. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example cam screw 118331). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA BRIMNES wardrobe with 3 doors assembly instructions
- IKEA BRIMNES bookcase assembly instructions
- IKEA BRIMNES cabinet with doors assembly instructions
- IKEA BRIMNES day-bed frame with 2 drawers assembly instructions
- IKEA BRIMNES dressing table assembly instructions
- IKEA BRIMNES chest of 4 drawers assembly instructions
- IKEA BRIMNES TV bench assembly instructions
- IKEA BRIMNES chest of 3 drawers assembly instructions
All IKEA BRIMNES assembly guides · All dressers & drawers assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained