Step by StepAssembly Find your furniture

IKEA BRIMNES cabinet with doors assembly instructions

How to assemble the IKEA BRIMNES cabinet with doors, step by step: 28 animated steps built from the official manual, about 1.5–2 hours for 1 person, with flat-blade screwdriver, Phillips screwdriver, pencil, hammer, wall screws and plugs (not included).

IKEA BRIMNES cabinet with doors, assembled

A low black BRIMNES cabinet: a cam-lock frame built lying on its front, a nailed-on back, wall fixing, two hinged frame-and-panel doors and two adjustable shelves. Size: 78x41x95 cm. About 1.5–2 hours, 1 person. Tools: Flat-blade screwdriver, Phillips screwdriver, Pencil, Hammer, Wall screws and plugs (not included).

Based on the official IKEA manual AA-1357217-9 (PDF). Guide updated .

BRIMNES cabinet with doors: quick facts
Steps28
Time1.5–2 hours
People1
ToolsFlat-blade screwdriver, Phillips screwdriver, Pencil, Hammer, Wall screws and plugs (not included)
Size78x41x95 cm
Official manualAA-1357217-9
IKEA article number803.006.60 (black)
Pieces in the box103

In the box

PartPart numberQuantity
Side panel2
Top1
Bottom board1
Top front rail1
Plinth1
Back panel (2 halves)1
Door2
Shelf2
Wall bracket1157532
Screw1003474
Hinge mounting plate1178784
Screw11328716
Cam screw11833110
Wooden dowel10134514
Cam lock 119252/11925010
Nail guide1054941
Nails 101221 (bag of 30)1
Glide 158568/1535484
Wall plate1036932
Bracket cover1157542
Hinge1178774
Handle1305082
Screw1095674
Cover cap 144833/1448342
Shelf pin1286438
Bumpers 107091 (sheet of 2)2

Steps

  1. Wall brackets on both side panels — Lay both side panels on a soft surface, inside faces up and front edges facing each other. Fix a wall bracket 115753 at the top back corner of each panel with 2 screws 100347. Check: Use the screws 100347 here, not the similar screws 113287.
  2. Hinge mounting plates — Screw 2 hinge mounting plates 117878 onto the inside of each side panel along the front edge, one near the top and one near the bottom, with 2 screws 113287 each.
  3. Cam screws into the side panels — Screw 3 cam screws 118331 into each side panel near the bottom end: two for the bottom board and one, close to the front edge, for the plinth.
  4. Bottom board onto the left side — Stand the left side panel on its front edge, inside facing you. Push 4 dowels 101345 into the ends of the bottom board and press its end onto the side panel, over the cam screws. Check: The bottom board’s unfinished long edge goes to the back.
  5. Lock the bottom board — Put 2 cam locks 119252 into the holes in the underside of the bottom board, next to the side panel, and turn them clockwise with a flat screwdriver until they grip the cam screws.
  6. Top front rail — Push 2 dowels 101345 into each end of the top front rail and press one end into the side panel at the top front corner.
  7. Plinth — Push a dowel 101345 into each end of the plinth and press it into the side panel at the bottom front corner, below the bottom board, with the cam lock holes facing the bottom board.
  8. Lock the plinth — Put a cam lock 119252 into the hole in the plinth next to the side panel and turn it to lock.
  9. Right side panel on — Stand the right side panel on its front edge, inside facing in, and push it onto the free ends of the bottom board, top rail and plinth so the dowels and cam screws go into their holes.
  10. Lock the right side — Insert 3 cam locks 119252: 2 in the underside of the bottom board and 1 in the plinth, next to the right side panel. Turn each one to lock.
  11. Cam screws into the top — Lay the top upside down on a soft surface and screw 4 cam screws 118331 into the holes near its corners.
  12. Fit the top — Push 4 dowels 101345 into the top edges of the side panels. Slide the top onto the end of the frame, cam screws first, so the dowels and cam screws go into the holes in the sides.
  13. Lock the top — Insert 4 cam locks 119252 in the inside faces of the side panels, just under the top, and turn each one to lock.
  14. Back panel and the first 2 nails — Lay the back panel on the back of the frame and line its edges up with the top and the left side at the top left corner. Use the nail guide 105494 to hold each nail and hammer 2 nails 101221 in at that corner, one into the top and one into the side. Check: Keep the edges of the back panel flush with the edges of the frame before nailing.
  15. Nail the back panel — Push the panel flush at the top right corner and nail it there, then square it at the bottom left corner and nail it. Then hammer in the other 26 nails along the sides, the top and the bottom board.
  16. Glides under the side panels — Tap 4 glides 158568 into the bottom edges of the side panels, 2 per side, with a hammer.
  17. Stand it up — Tip the cabinet up onto its glides, then turn it round so the front faces you. Check: Get help to stand the cabinet up.
  18. Mark the wall — Push the cabinet against the wall where it will stand. Mark the wall with a pencil through the hole in each of the 2 wall brackets. Check: The cabinet can tip over: it must be fixed to the wall. Screws and plugs for the wall are not included; choose ones that suit your wall.
  19. Drive 2 wall screws — Move the cabinet away. Drill and plug the wall at the 2 marks if your wall needs it, then drive in 2 screws with a round (pan) head. Leave the heads standing out a few millimetres. Check: Use screws with a flat-underside round head, not countersunk screws.
  20. Fix it to the wall — Push the cabinet back so the screw heads come through the brackets. Slide a wall plate 103693 into each bracket over the screw head, tighten the screw, then click a cover 115754 over the bracket.
  21. Hinges on the doors — Lay both doors face down. Press 2 hinges 117877 into the round holes of each door, arms pointing out, and fix each hinge with 2 screws 113287.
  22. Hang the doors — Hook each hinge arm onto its mounting plate in the cabinet and press until it clicks. Then tighten the screw at the back of each hinge arm. Check: The doors can be adjusted up and down, sideways and in and out with the hinge screws (last page of the manual).
  23. Handles — Hold a handle 130508 on the front of each door, on the stile next to the opening, and screw it on from the back with 2 screws 109567.
  24. Cover caps in the bottom — Press the 2 cover caps into the holes in the bottom board. Use the black caps 144833 on this black cabinet.
  25. Shelf pins — Push 8 shelf pins 128643 into the holes in the side panels, 4 at the same height for each shelf.
  26. Shelves — Lay the 2 shelves on the shelf pins.
  27. Bumpers on the doors — Stick 4 bumpers 107091 on the back of the doors, at the top and bottom corners next to the opening. Then close the doors.
  28. Done! — Your BRIMNES cabinet is finished and fixed to the wall. The shelves can be moved to other heights with the shelf pins.

BRIMNES cabinet with doors: questions and answers

How long does it take to assemble the IKEA BRIMNES cabinet with doors?

About 1.5–2 hours for 1 person, working through the 28 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the BRIMNES cabinet with doors?

Flat-blade screwdriver, Phillips screwdriver, pencil, hammer, wall screws and plugs (not included).

Can one person assemble the BRIMNES cabinet with doors?

Yes, it is a one-person build.

Does the BRIMNES cabinet with doors need to be fixed to the wall?

The manual shows a wall fixing: see step 1 (Wall brackets on both side panels) and step 18 (Mark the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the BRIMNES cabinet with doors once assembled?

78x41x95 cm, as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the BRIMNES cabinet with doors?

89 fittings of 16 kinds, the most numerous being 16 × screw, 14 × wooden dowel, 10 × cam screw. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA BRIMNES cabinet with doors assembly instructions PDF?

The official PDF is manual AA-1357217-9, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 803.006.60 (black); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-1357217-9. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example wall bracket 115753). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA BRIMNES assembly guides · All bookcases & shelves assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained