Step by StepAssembly Find your furniture

IKEA BRIMNES wardrobe with 3 doors assembly instructions

How to assemble the IKEA BRIMNES wardrobe with 3 doors (closet), step by step: 44 animated steps built from the official manual, about 2½–3½ h for 2 people, with flat & Phillips screwdriver, hammer, pencil, drill, step ladder, Allen key (included).

IKEA BRIMNES wardrobe with 3 doors, assembled

A white three-door wardrobe with a mirror door: cam-lock frame built lying down, nailed folding back panel, hinged doors, clothes rail, shelves and wall anchoring. Size: 117×50×190 cm (46×19 5/8×74 3/4"). About 2½–3½ h, 2 people. Tools: Flat & Phillips screwdriver, Hammer, Pencil, Drill, Step ladder, Allen key (included).

Based on the official IKEA manual AA-2207256-4 (PDF). Guide updated .

BRIMNES wardrobe with 3 doors: quick facts
Steps44
Time2½–3½ h
People2
ToolsFlat & Phillips screwdriver, Hammer, Pencil, Drill, Step ladder, Allen key (included)
Size117×50×190 cm (46×19 5/8×74 3/4")
Official manualAA-2207256-4
IKEA article number404.079.22 (white)
Pieces in the box243

In the box

PartPart numberQuantity
Side panel2
Top panel1
Bottom panel1
Divider1
Fixed shelf1
Plinth rail2
Back panel (folding)1
Shelf3
Clothes rail 122663/1195431
Door2
Mirror door1
Screw1002144
Cam screw11833114
Cam lock 119252/11925014
Dowel10134522
Screw1095676
Screw1090495
Screw10524841
Door stop 123840/1098373
Handle 124328/128763/1459153
Allen key1000011
Shelf pin10153212
Bumper pad sheet1070912
Glide 153548/1585686
Angle bracket1025533
Rail holder 157306/1573072
Nail guide1054941
Nail10129360
Mounting plate1092209
Hinge1093369
Wall bracket1069892
Washer1008234
Screw1090482
Plug1217142

Steps

  1. Cam screws into the divider — Work on a rug or the cardboard. Lay the divider flat with the side that has the 2 small holes near the middle facing up and the edge with the cam-lock holes towards you. Screw the 2 cam screws (118331) into those holes. Check: This wardrobe is heavy and tall: two people are needed for several steps. Protect the floor and the panels with a soft surface.
  2. Fixed shelf onto 2 dowels — Push 2 dowels (101345) into the divider next to the cam screws. Stand the fixed shelf on its end onto the dowels and cam screws, with the holes in its face towards you.
  3. Lock the fixed shelf — Put 2 cam locks (119252/119250) into the holes in the shelf next to the divider, arrow towards the cam screw, and turn each one clockwise with a flat screwdriver until it grips.
  4. Turn it over, fit the bottom panel — Turn the divider and shelf over so the divider stands on its back edge and the shelf points to the right. Push 2 dowels into the end of the divider and slide the bottom panel onto them.
  5. Screw the bottom panel to the divider — Drive 2 screws (100214) through the bottom panel into the end of the divider with the Allen key (100001).
  6. Cam screws into the side panels — Lay both side panels flat, inside face up, with the groove for the back panel along the edge nearest the frame. Screw in the cam screws: 3 in the left side panel and 5 in the right one.
  7. Hinge mounting plates on the side panels — Screw 3 mounting plates (109220) to each side panel near its front edge, with 2 screws (105248) each.
  8. Right side panel — Push 6 dowels into the ends of the bottom panel and the end of the fixed shelf. Stand the right side panel on its back edge and press it onto the dowels and cam screws.
  9. Lock the right side panel — Insert 4 cam locks: 2 in the bottom panel and 2 in the fixed shelf, and turn them to lock.
  10. Dowels into the plinth rails — Lay out the two plinth rails. Push 6 dowels into their ends: 2 at each end of the back rail and 1 at each end of the front rail.
  11. Back plinth rail — Fit the back plinth rail into the right side panel, at floor level under the bottom panel. The holes in the rail face up, away from the floor.
  12. Left side panel and front plinth rail — With a helper, tip the left side panel up onto the dowels and cam screws of the bottom panel while sliding the front plinth rail into place at the top edge. Check: Two people: one holds the side panel, the other guides the rail.
  13. Lock the left side panel — Insert 4 cam locks: 2 in the bottom panel near the left side and 1 at each end of the front plinth rail, and turn them to lock.
  14. Angle brackets under the bottom panel — Screw 3 angle brackets (102553) to the underside of the bottom panel with screws 105248: 2 against the front plinth rail and 1 against the back one.
  15. Screw the brackets to the plinth rails — Fix each bracket to its plinth rail with a short screw (109049). Check: Use the short screws 109049 here, not the longer 109567 (those are for the handles).
  16. Cam screws into the top panel — Lay the top panel flat beyond the top end, underside up. Screw the 4 cam screws (118331) into the holes at its corners.
  17. Door stops into the top panel — Tap the 3 door stops (123840/109837) into the holes near the front edge of the top panel with a hammer.
  18. Top panel — Push 6 dowels into the top ends of the side panels and the divider. Tip the top panel up and press it onto the dowels and cam screws.
  19. Screw the top panel to the divider — Drive 2 screws (100214) through the top panel into the divider with the Allen key.
  20. Lock the top panel — Insert 4 cam locks into the side panels just below the top panel and turn them to lock.
  21. Glides under the bottom edges — Tap the 6 glides (153548/158568) into the bottom edges: 2 under each side panel and 2 under the front plinth rail.
  22. Turn the frame onto its front — With a helper, roll the frame over a long edge: first onto its side, then down onto its front, so the back faces up. Check: Two people needed. Lift, don’t drag, so the joints are not strained.
  23. Lay on the back panel — Unfold the back panel and lay it on the frame, smooth side down, so it drops into the rebates of the side and top panels.
  24. Square the back panel — Push the back panel into the rebate at the top corner and along both sides, so the gaps are even all round.
  25. First nail — Hold the nail guide (105494) against the edge, put a nail (101293) through it and tap it into the top corner. Slide the guide away and drive the nail home.
  26. Nail the opposite corners — Check that the back panel is still square, then nail the other top corner and the opposite bottom corner, with the nail guide each time.
  27. Last corner — Nail the fourth corner with the nail guide.
  28. Nail all round the edge — Nail the back panel all round the edge, using the nail guide for the spacing: 35 nails.
  29. Nail along the divider and bottom panel — Hammer 10 nails along the line of the divider and 10 along the bottom panel.
  30. Wall brackets, then stand it up — Screw the 2 wall brackets (106989) to the top panel with a screw (109049) and washer (100823) each, at the top of the slot. Then, with a helper, tip the wardrobe up and carry it to its place against the wall. Check: Two people needed. Check there is enough room under the ceiling to tip it up.
  31. Mark the wall — With the wardrobe against the wall, mark the wall through the slot in each bracket. Check: The wardrobe must be fixed to the wall to stop it tipping over. Use a step ladder; don’t lean on the wardrobe.
  32. Drill the holes — Pull the wardrobe away from the wall and drill a hole at each mark. Choose the drill bit for your wall type (see the next step).
  33. Plugs in the wall — For solid or hollow walls, tap a plug (121714) into each hole. In solid wood, use the screws without plugs. If unsure which fixings suit your wall, ask a specialist.
  34. Screw the brackets to the wall — Push the wardrobe back against the wall. Screw a screw (109048) with a washer through each bracket into the plug.
  35. Tighten the bracket screws — Tighten the screws that hold the brackets on the top panel.
  36. Mounting plates on the divider — Screw 3 mounting plates (109220) to the left face of the divider, near its front edge, with 2 screws (105248) each.
  37. Hinges on the doors — Lay the 3 doors flat, inside face up. Press a hinge (109336) into each of the 9 round holes and fix it with 2 screws (105248).
  38. Hang the doors — Hook each hinge arm onto its mounting plate and tighten the screw on the arm. The mirror door can go in any of the three places; here it is in the middle. Check: The doors are heavy: have a helper hold each door while you clip it on.
  39. Handles — Open the doors. Hold each handle against the front of its door and screw it on from the inside with 2 screws (109567).
  40. Shelf in the left section — Push 4 shelf pins (101532) into the holes at the height you want in the left section, then lower the shelf onto them.
  41. Clothes rail — Screw a rail holder (157306/157307) to the left side panel and one to the divider with a screw (105248) each, then drop the clothes rail into the holders.
  42. Shelves in the right section — Push 8 shelf pins into the right section, 4 above and 4 below the fixed shelf, and lower the 2 shelves onto them.
  43. Bumper pads on the doors — Stick a bumper pad from the sheets (107091) on the inside of each door, near the bottom corner of the opening edge, then close the doors.
  44. Done! — Close the doors: your BRIMNES wardrobe is ready. If a door hangs crooked, adjust it with the screws on its hinges (height, side and depth). Keep it fixed to the wall.

BRIMNES wardrobe with 3 doors: questions and answers

How long does it take to assemble the IKEA BRIMNES wardrobe with 3 doors?

About 2½–3½ h for 2 people, working through the 44 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the BRIMNES wardrobe with 3 doors?

Flat & Phillips screwdriver, hammer, pencil, drill, step ladder, Allen key (included). Already in the box: Allen key.

Can one person assemble the BRIMNES wardrobe with 3 doors?

It is planned as a 2-person build. One person can do most of it, but get help for steps 4, 12 and 18, where the furniture is lifted or turned.

Does the BRIMNES wardrobe with 3 doors need to be fixed to the wall?

The manual shows a wall fixing: see step 30 (Wall brackets, then stand it up) and step 31 (Mark the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the BRIMNES wardrobe with 3 doors once assembled?

117×50×190 cm (46×19 5/8×74 3/4"), as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the BRIMNES wardrobe with 3 doors?

227 fittings of 23 kinds, the most numerous being 60 × nail, 41 × screw, 22 × dowel. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA BRIMNES wardrobe with 3 doors assembly instructions PDF?

The official PDF is manual AA-2207256-4, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 404.079.22 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2207256-4. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example clothes rail 122663). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA BRIMNES assembly guides · All wardrobes assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained