IKEA BRIMNES dressing table assembly instructions
How to assemble the IKEA BRIMNES dressing table, step by step: 53 animated steps built from the official manual, about 2–3 hours for 1 person, with flat-blade screwdriver, Phillips screwdriver, hammer, hex key 100001 (included).
A white BRIMNES dressing table: a cam-lock frame built lying down, a drawer on runner rails, and a mirror lid on concealed hinges with a lid stay over a divided storage compartment. Size: 70x42 cm. About 2–3 hours, 1 person. Tools: Flat-blade screwdriver, Phillips screwdriver, Hammer, Hex key 100001 (included).
Based on the official IKEA manual AA-1357280-11 (PDF). Guide updated .
| Steps | 53 |
|---|---|
| Time | 2–3 hours |
| People | 1 |
| Tools | Flat-blade screwdriver, Phillips screwdriver, Hammer, Hex key 100001 (included) |
| Size | 70x42 cm |
| Official manual | AA-1357280-11 |
| IKEA article number | 702.904.59 (white) |
| Pieces in the box | 111 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Side panel | 2 | |
| Back panel | 1 | |
| Shelf | 1 | |
| Divider board | 2 | |
| Top | 1 | |
| Back strip | 1 | |
| Mirror lid | 1 | |
| Long partition | 1 | |
| Short partition | 1 | |
| Front panel | 1 | |
| Drawer front | 1 | |
| Drawer side | 2 | |
| Drawer back | 1 | |
| Drawer bottom | 1 | |
| Cam screw | 118331 | 18 |
| Cam lock 119030/117434/118224 | 20 | |
| Wooden dowel | 101345 | 20 |
| Runner rail | 107581 | 2 |
| Glide 153548/158568 | 4 | |
| Screw | 102138 | 2 |
| Screw | 100214 | 3 |
| Hex key | 100001 | 1 |
| Expansion dowel | 110519 | 5 |
| Stop screw | 102323 | 2 |
| Hinge 116499/115992 | 2 | |
| Screw | 109533 | 8 |
| Lid stay | 115307 | 1 |
| Screw | 109535 | 4 |
| Cam screw 123492 (bag of 2) | 2 |
Steps
- Cam screws into the side panels — Lay both side panels on a soft surface, inside facing up and top ends the same way. Screw 4 cam screws 118331 into the small holes near the top end of each panel. Check: Use cam screws 118331 here, not the shorter-shouldered 123492 from the separate bag.
- Runner rail on the left side panel — Set the runner rail 107581 into the 4 holes near the top end of the left side panel and tap it in with a hammer until it sits flat.
- Glides under the side panels — Press 2 glides 153548 into the holes in the bottom end of each side panel.
- Back panel onto the right side — Push 4 dowels 101345 into the end edges of the back panel. Stand it on the right side panel along its back edge, at the top end, over the dowel holes and cam screws.
- Lock the back panel — Put 2 cam locks into the holes near the bottom of the back panel and turn each one clockwise with a flat screwdriver until it grips the cam screw.
- Shelf onto the right side — Push 4 dowels 101345 into the end edges of the shelf and stand it on the right side panel, its back edge against the back panel.
- Lock the shelf — Put 2 cam locks into the holes in the underside of the shelf, next to the side panel, and turn them clockwise to lock.
- Left side panel on — Turn the left side panel over, rail facing down, and lower it onto the back panel and the shelf so the dowels and cam screws go into their holes.
- Lock the left side panel — Put 4 cam locks in: 2 near the top of the back panel and 2 in the underside of the shelf, next to the left side panel. Turn each one clockwise to lock.
- Lay the frame on its back — Tip the frame over its back edge so it lies on the back panel, front edges facing up.
- Screw the divider boards together — Hold the two divider boards together, with the holes in their front edges at the same end, and join them with 2 screws 102138 through the board with the large cam lock holes.
- Runner rail on the divider — Lay the divider down with the other board on top. Set the second runner rail 107581 in the 4 holes and hammer it in flat.
- Divider into the frame — Lower the divider into the frame between the side panels, rail towards the left side panel, and push it against the shelf where its holes are.
- Screw the divider to the shelf — From the other side of the shelf, screw 2 screws 100214 up through the shelf into the divider with the hex key 100001.
- Stand the frame up — Stand the frame up on its glides and turn it round so the front faces you.
- Screw the divider to the back panel — From behind, screw a screw 100214 through the back panel into the back edge of the divider with the hex key.
- Dowels in the top edges — Push 6 dowels 101345 into the top edges: 3 in the back panel, 1 at the front of the left side panel, 1 at the front of the divider and 1 at the back of the right side panel.
- Cam screws into the top — Lay the top upside down on a soft surface and screw 4 cam screws 118331 into the holes near its long edges.
- Top onto the left part — Turn the top over and lower it onto the left side panel and the divider, cam screws and dowels into their holes, back edge flush with the back panel.
- Lock the top — Put 4 cam locks into the holes just under the top: 2 in the left side panel and 2 in the divider. Turn each one clockwise to lock.
- Cam screws into the drawer front — Now the drawer. Lay the drawer front face down on a soft surface and screw 2 cam screws 118331 into the small holes near its ends.
- Drawer sides on — Push 2 dowels 101345 into the drawer front. Stand the drawer sides on it, grooves facing out, over the dowels and the cam screws.
- Lock the drawer sides — Put a cam lock into the hole in the outside of each drawer side, next to the front, and turn it clockwise to lock.
- Slide in the drawer bottom — Slide the drawer bottom down into the grooves in the sides from the open end until it reaches the front.
- Drawer back — Lower the drawer back between the sides at the open end, notch side first, so it sits over the drawer bottom.
- Expansion dowels in the sides — Push 4 expansion dowels 110519 by hand through the holes in the drawer sides into the ends of the back, 2 on each side.
- Hammer the dowels home — Lay the drawer on its side on a table, front hanging over the edge, and hammer the 2 dowels on top flush. Turn the drawer over and hammer the other 2.
- Put the drawer in — Turn the drawer upright, hold it in front of the opening under the top with its side grooves level with the runner rails, and push it in all the way.
- Drawer stops — Pull the drawer out most of the way. Screw a stop screw 102323 into the hole inside each drawer side near the back, then push the drawer back in.
- Cam screws into the back strip — Lay the narrow back strip upside down and screw 2 cam screws 118331 into the holes near its ends.
- Back strip on — Turn the strip over and lower it onto the back of the right part, onto the divider and the right side panel, holes for the hinges facing forward.
- Expansion dowel in the strip — Push an expansion dowel 110519 by hand into the small hole in the front edge of the back strip, at the left end.
- Lock the back strip — Put 2 cam locks into the holes under the back strip, one in the divider and one in the right side panel, and turn them clockwise to lock.
- Hinges into the back strip — Push the 2 hinges 116499 into the oval holes in the front edge of the back strip.
- Fold the hinges open — Fold the free half of each hinge up and over onto the top of the strip.
- Screw the hinges to the strip — Fix each hinge to the strip with 2 screws 109533 through the holes in the half that sits in the strip.
- Mirror lid onto the hinges — Hold the mirror lid upside down behind the table, mirror facing up, and push its back edge onto the open halves of the hinges.
- Screw the hinges to the lid — Fix the hinges to the lid with 2 screws 109533 each.
- Lid stay onto the lid — Fix the top bracket of the lid stay 115307 to the lid near its right edge with 2 screws 109535, stay pointing towards the hinges.
- Lid up, stay onto the side — Swing the lid up until it leans back a little. Pull the stay down to the right side panel and fix its lower bracket with 2 screws 109535.
- Cam screw into the divider — Take a cam screw 123492 from the separate bag and screw it into the small hole in the middle of the divider, inside the compartment.
- Cam screw into the long partition — Lay the long partition flat and screw the other cam screw 123492 into the small hole in its face.
- Short partition onto the long one — Push a dowel 101345 into each end of the short partition. Stand it on the long partition over the cam screw, the dowel going into the hole next to it.
- Lock the partitions together — Put a cam lock into the hole in the short partition next to the long one and turn it clockwise to lock.
- Partitions into the compartment — Lower the T of partitions into the compartment, long partition front to back. Swing it round until the free end of the short one meets the divider, its dowel and hole going onto the cam screw.
- Lock the partitions to the divider — Put a cam lock into the hole in the short partition next to the divider and turn it clockwise to lock.
- Dowels in the front edges — Push a dowel 101345 into the front edge of the divider and one into the front edge of the right side panel, next to the compartment.
- Cam screws into the front panel — Lay the compartment front panel face down and screw 2 cam screws 118331 into the holes near its ends.
- Front panel on — Lift the front panel up in front of the compartment and push it onto the dowels and into the front edges of the divider and the right side panel.
- Lock the front panel — Put 2 cam locks into the holes inside the compartment, next to the front panel, and turn them clockwise to lock.
- Against the wall — Close the lid. Stand the dressing table against the wall where it will be used. Check: If there is a skirting board, fit spacers (not included) behind the fixing points so the table stands straight.
- Fix it to the wall — From under the shelf, screw 2 wall screws through the holes near the ends of the back panel into the wall. Check: Fix the table to the wall to stop it tipping over. Screws and plugs are not included: choose ones that suit your wall.
- Done! — Your BRIMNES dressing table is finished. The drawer runs on its rails. Lift the lid for the mirror and the divided storage compartment: the stay holds it open.
BRIMNES dressing table: questions and answers
How long does it take to assemble the IKEA BRIMNES dressing table?
About 2–3 hours for 1 person, working through the 53 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the BRIMNES dressing table?
Flat-blade screwdriver, Phillips screwdriver, hammer, hex key 100001 (included). Already in the box: Hex key 100001.
Can one person assemble the BRIMNES dressing table?
Yes, it is a one-person build.
Does the BRIMNES dressing table need to be fixed to the wall?
The manual shows a wall fixing: see step 52 (Fix it to the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.
What size is the BRIMNES dressing table once assembled?
70x42 cm, as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the BRIMNES dressing table?
92 fittings of 14 kinds, the most numerous being 20 × cam lock 119030/117434/118224, 20 × wooden dowel, 18 × cam screw. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA BRIMNES dressing table assembly instructions PDF?
The official PDF is manual AA-1357280-11, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 702.904.59 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-1357280-11. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example cam screw 118331). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA BRIMNES wardrobe with 3 doors assembly instructions
- IKEA BRIMNES bookcase assembly instructions
- IKEA BRIMNES cabinet with doors assembly instructions
- IKEA BRIMNES bedside table assembly instructions
- IKEA BRIMNES day-bed frame with 2 drawers assembly instructions
- IKEA BRIMNES chest of 4 drawers assembly instructions
- IKEA BRIMNES TV bench assembly instructions
- IKEA BRIMNES chest of 3 drawers assembly instructions
All IKEA BRIMNES assembly guides · All dressers & drawers assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained