Step by StepAssembly Find your furniture

IKEA BRIMNES TV bench assembly instructions

How to assemble the IKEA BRIMNES TV bench, step by step: 46 animated steps built from the official manual, about 2–3 hours for 1 person, with flat-blade screwdriver, Phillips screwdriver, hammer, pencil, wall screws and plugs to suit your wall (not included).

IKEA BRIMNES TV bench, assembled

A black BRIMNES TV bench: a cam-lock frame built lying on its front, a nailed-on back, fixed to the wall, and two framed drawers on runners under two open compartments. Size: 120x41x53 cm. About 2–3 hours, 1 person. Tools: Flat-blade screwdriver, Phillips screwdriver, Hammer, Pencil, Wall screws and plugs to suit your wall (not included).

Based on the official IKEA manual AA-1871703-12 (PDF). Guide updated .

BRIMNES TV bench: quick facts
Steps46
Time2–3 hours
People1
ToolsFlat-blade screwdriver, Phillips screwdriver, Hammer, Pencil, Wall screws and plugs to suit your wall (not included)
Size120x41x53 cm
Official manualAA-1871703-12
IKEA article number503.376.98 (black)
Pieces in the box180

In the box

PartPart numberQuantity
Side panel2
Shelf1
Divider (upper)1
Partition (between the drawers)1
Plinth rail2
Top1
Back panel1
Drawer front2
Drawer side4
Drawer back2
Drawer bottom2
Connector screw1002142
Allen key1000011
Cam screw11833124
Wooden dowel10134526
Screw10036516
Cam lock 119250/11925216
Cam lock 118224/1190308
Screw1053446
Washer1008234
Wall bracket1069892
Glide 153548/1585686
Nail holder1054941
Nails 101221 (bag)30
Expansion screw1105198
Screw1095674
Drawer runner set 158933 (4 rails)2
Stay rail1237712
Handle1305082
Bumpers 107091 (sheet of 2)1

Steps

  1. Lay out the panels — Lay the shelf, both side panels, the partition and the divider on a rug or the empty carton, so they don’t get scratched. Side panels inside face up. Check: Check the edges: the side panels have a rebate along their back edge for the back panel.
  2. Runners on the side panels and partition — Lay a carcass runner along the bottom end of each side panel and of the partition, wheel at the front edge, and fix each with 2 screws 100365. Check: The runners are marked L and R: match them to the side of the drawer opening they face.
  3. Cam screws into the side panels — Screw 4 cam screws 118331 into the small holes on the inside of each side panel: 2 at the middle for the shelf and 2 at the bottom end for the plinth rails.
  4. Shelf and divider — Stand the shelf on its front edge. Swing the divider up against the far face of the shelf, in the middle, and fix it with 2 connector screws 100214 through the shelf, using the Allen key 100001.
  5. Dowels — Push 14 dowels 101345 into the holes: 2 into each end of the shelf, 2 into the free end of the divider, 2 into the top edge of each side panel, and 2 into each end of the partition.
  6. Cam screws into the shelf — Screw 2 cam screws 118331 into the small holes in the middle of the shelf, on the side facing you (the underside). They will hold the partition.
  7. First side panel and the partition — Swing the first side panel up onto the end of the shelf, inside facing in, so the dowels and cam screws go into their holes. Then swing the partition up onto the middle of the shelf, its runner facing the side panel.
  8. Lock the side panel and partition — Put 2 cam locks 119250 into the shelf next to the side panel and 2 into the partition next to the shelf. Turn each one clockwise with a flat screwdriver until it grips the cam screw.
  9. Second runner on the partition — Fix a carcass runner to the other face of the partition, at the bottom end with the wheel at the front, using 2 screws 100365.
  10. Dowels in the plinth rails — Lay the 2 plinth rails down and push a dowel 101345 into the hole at each end, 4 in all.
  11. Plinth rails on — Fit the 2 plinth rails at the bottom end: one along the front edges, one along the back edges. Push each onto the side panel’s dowel and cam screw and onto the partition’s dowel.
  12. Lock the plinth rails — Put a cam lock 119250 into each plinth rail next to the side panel and turn it clockwise to lock.
  13. Second side panel — Swing the second side panel up onto the other ends of the shelf and the plinth rails, inside facing in, so the dowels and cam screws go into their holes.
  14. Lock the second side panel — Put 2 cam locks 119250 into the shelf and 1 into each plinth rail next to the second side panel, and turn each one clockwise to lock.
  15. Glides — Tap 6 glides 153548 into the holes in the bottom edges with a hammer: 2 under each side panel and 1 under the middle of each plinth rail.
  16. Cam screws into the top — Lay the top upside down on the rug, front edge away from the frame. Screw 6 cam screws 118331 into the small holes: 2 near each end and 2 in the middle.
  17. Wall brackets on the top — Lay a wall bracket 106989 at each back corner of the top, upright leg along the back edge. Fix each with a washer 100823 and a screw 105344 through the slot.
  18. Stand it up, top on — Stand the frame up on its glides. Turn the top over and lower it onto the frame, so the dowels and cam screws go into the holes in the sides and the divider.
  19. Lock the top — Put 6 cam locks 119250 into the holes just under the top: 2 in each side panel and 2 in the divider. Turn each one clockwise to lock.
  20. Lay it on its front, mark the divider — Lay the bench on its front on the rug. With a pencil, mark the middle of the divider on the back edge of the top and on the back plinth rail, so you can find it once the back panel is on.
  21. Lay on the back panel — Lay the back panel on the back of the bench, the cable hole at the top and the notches over the wall brackets.
  22. The first nails — Push the back panel up to the top so its edges are flush with it at one wall bracket. Hold a nail 101221 in the nail holder 105494 and hammer it in on one side of the notch, then nail the other side.
  23. Nail the bottom corners — Line the back panel up with the side panels at both bottom corners, just above the back plinth rail, and nail each corner with the nail holder.
  24. Nail the back panel all round — Nail the rest of the edges with 21 nails 101221 through the holes: along both side panels and along the top, using the nail holder.
  25. Draw the divider line — Draw a line across the back panel between your two pencil marks. The divider sits under this line.
  26. Nail into the divider — Nail 5 nails 101221 along the line into the divider, using the nail holder.
  27. Stand it up — Stand the bench up on its glides, with the back towards the wall where it will stand.
  28. Plugs in the wall — Mark the wall through the slots in the 2 wall brackets, then pull the bench away. Drill and push in 2 plugs suitable for your wall (wall screws and plugs are not included). Check: The bench must be fixed to the wall so it can’t tip over. Ask your local shop for the right screws and plugs for your wall.
  29. Push it back to the wall — Push the bench back against the wall, so the slots in the wall brackets line up with the plugs.
  30. Screw it to the wall — Reach into the open compartments. Put a washer 100823 on each wall screw and screw it through the wall bracket into the plug.
  31. Drawer: cam screws in the front — Now the drawers (bag 2), one at a time. Lay a drawer front face down and screw 4 cam screws 118331 into the small holes on its inside. Lay 2 drawer sides next to it.
  32. Dowels in the drawer sides — Push 2 dowels 101345 into the front end of each drawer side.
  33. Drawer sides onto the front — Stand the drawer sides on the front, grooves facing in, and press them down onto the cam screws so the dowels go into their holes.
  34. Lock the drawer sides — Put 4 cam locks 118224 into the holes on the inside of the drawer sides, next to the front, and turn each one clockwise to lock.
  35. Slide in the drawer bottom — Slide the drawer bottom down into the grooves in the sides, from the open end, until it reaches the front.
  36. Drawer back — Place the drawer back between the sides at the open end, on the drawer bottom. Hammer 4 expansion screws 110519 through the sides into its ends, 2 on each side.
  37. Runners on the drawer — Tip the drawer over onto its front edge so it is upside down. Lay a drawer runner on the bottom edge of each side, wheel at the back. Check: The drawer runners are marked L and R as well.
  38. Screw on the runners — Fix each drawer runner with 2 screws 100365 into the side.
  39. Stay rail: first end — Screw a screw 105344 into the drawer back near one end, then hook that end of the stay rail 123771 over its head, the rail lying along the back edge.
  40. Stay rail: other end — Turn the rail’s other tab against the drawer back and fix it with a screw 105344.
  41. Handle — Turn the drawer the right way up. Hold the handle 130508 on the top band of the front and screw it on from the inside with 2 screws 109567.
  42. The second drawer — Build the second drawer the same way: cam screws, dowels and sides on the front, cam locks, bottom, back with expansion screws, runners, stay rail and handle.
  43. First drawer in — Hold the right-hand drawer in front of its opening, tilt the front up a little and set its back wheels on the runners in the bench. Slide it in, lower the front and push it all the way home.
  44. Second drawer in — Put the second drawer into the left-hand opening the same way.
  45. Bumpers — Pull the right-hand drawer out. Stick the 2 bumpers 107091 on the front edges where its front closes: one on the partition and one on the side panel. Push the drawer shut.
  46. Done! — Your BRIMNES TV bench is finished and fixed to the wall. Run cables through the hole in the back panel; the drawers glide out on their runners.

BRIMNES TV bench: questions and answers

How long does it take to assemble the IKEA BRIMNES TV bench?

About 2–3 hours for 1 person, working through the 46 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the BRIMNES TV bench?

Flat-blade screwdriver, Phillips screwdriver, hammer, pencil, wall screws and plugs to suit your wall (not included).

Can one person assemble the BRIMNES TV bench?

Yes, it is a one-person build.

Does the BRIMNES TV bench need to be fixed to the wall?

The manual shows a wall fixing: see step 17 (Wall brackets on the top) and step 28 (Plugs in the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the BRIMNES TV bench once assembled?

120x41x53 cm, as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the BRIMNES TV bench?

127 fittings of 15 kinds, the most numerous being 26 × wooden dowel, 24 × cam screw, 16 × screw. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA BRIMNES TV bench assembly instructions PDF?

The official PDF is manual AA-1871703-12, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 503.376.98 (black); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-1871703-12. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example connector screw 100214). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA BRIMNES assembly guides · All chairs & stools assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained