Step by StepAssembly Find your furniture

IKEA EKET cabinet assembly instructions

How to assemble the IKEA EKET cabinet, step by step: 15 animated steps built from the official manual, about 20–30 min for 1 person, with drill with Ø 8 mm bit, spirit level, screwdriver.

IKEA EKET cabinet, assembled

Small open EKET cube: four mitred panels that hook together without screws, a slide-in back panel and wall fixing with adjustable spacers. Size: 35×25×35 cm (13 3/4×9 7/8×13 3/4"). About 20–30 min, 1 person. Tools: Drill with Ø 8 mm bit, Spirit level, Screwdriver.

Based on the official IKEA manual AA-2702649-1 (PDF). Guide updated .

EKET cabinet: quick facts
Steps15
Time20–30 min
People1
ToolsDrill with Ø 8 mm bit, Spirit level, Screwdriver
Size35×25×35 cm (13 3/4×9 7/8×13 3/4")
Official manualAA-2702649-1
IKEA article number703.321.24 (white)
Pieces in the box22

In the box

PartPart numberQuantity
Panel with pegs (top / bottom)2
Panel with keyhole slots (side)2
Back panel1
Back-panel clip100930814
Clip pin100930824
Wall spacer fitting1414132
Spacer knob1414142
Washer1526512
Cover cap1526502
Planning sheet / drilling template AA-26935151

Steps

  1. Sort the four panels — Lay the 4 panels flat on a rug, inner side up. Two have small pegs at both ends (top and bottom panels) and two have keyhole slots (side panels). The panel marked “1” is the top. Check: Work on a soft surface so the mitred edges do not get chipped.
  2. Hook the top panel onto a side panel — Stand a side panel on its front edge, back-panel groove at the top. Hold the top panel at a right angle above its end, put the pegs in the wide part of the keyhole slots and push it down until it locks. Press the corner together. Check: The small marks on the panel edges all go to the back (facing up).
  3. Second side panel — Lower the second side panel onto the other end of the top panel in the same way, so its keyhole slots slide down over the pegs.
  4. Slide in the back panel — Slide the back panel into the grooves of the two side panels from the open end, all the way into the groove of the top panel. Check: The back panel must run inside the grooves, not on top of them.
  5. Close the frame with the bottom panel — Lower the bottom panel onto the open end so its pegs drop into both side panels at once. Then turn the cabinet upright.
  6. Push the back panel down — From the back, push the back panel down until its lower edge drops into the groove of the bottom panel. The “1” on the top panel is at the top. Check: Check that the back panel sits in the bottom groove and not on its edge.
  7. Lock the back panel: 4 clips — Push a clip (10093081) into the hole in the middle of each edge behind the back panel, then press a pin (10093082) into each clip with your thumb so it locks.
  8. Legs or wall mounting: separate manuals — Decide how the cabinet will stand. On legs (shown here) or on another EKET: fit the legs as their own manual shows, then continue with step 9. Hanging on the wall: EKET suspension rail, sold separately with its own manual; this manual stops here for that option. Check: Legs and the suspension rail are separate products and are not in this box.
  9. Wall spacer fittings at the top corners — From the back, press a wall spacer fitting (141413) into the two holes near the top of each side panel, behind the back panel, with the threaded drum towards the middle.
  10. Drill through the fittings — Drill through the marked centre of each spacer fitting and the back panel with an 8 mm bit. With stacked EKET cabinets, only the top cabinet needs these holes.
  11. Screw on the knobs — If there is a skirting board, screw a knob (141414) onto each spacer fitting, clockwise, all the way in. Without a skirting board, go straight to step 13.
  12. Against the wall, knobs out to the wall — Push the cabinet back until the back legs touch the skirting board. Turn both knobs anticlockwise until they rest against the wall, so the cabinet stands straight. Check: Check with a spirit level; level the legs as their manual shows.
  13. Screw it to the wall from inside — From inside, put a washer (152651) over each drilled hole, the right way round, and screw into the wall. Check: Fix it to the wall to stop it tipping over. Wall screws and plugs are not included.
  14. Cover caps — Press a cover cap (152650) onto each washer and turn it to lock it in place.
  15. Done! — Your EKET cabinet is assembled and fixed to the wall. Max load: 5 kg. To hang it on the wall instead, use the EKET suspension rail and its own manual.

EKET cabinet: questions and answers

How long does it take to assemble the IKEA EKET cabinet?

About 20–30 min for 1 person, working through the 15 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the EKET cabinet?

Drill with Ø 8 mm bit, spirit level, screwdriver.

Can one person assemble the EKET cabinet?

Yes, it is a one-person build.

Does the EKET cabinet need to be fixed to the wall?

The manual shows a wall fixing: see step 8 (Legs or wall mounting: separate manuals) and step 9 (Wall spacer fittings at the top corners). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the EKET cabinet once assembled?

35×25×35 cm (13 3/4×9 7/8×13 3/4"), as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the EKET cabinet?

17 fittings of 7 kinds, the most numerous being 4 × back-panel clip, 4 × clip pin, 2 × wall spacer fitting. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA EKET cabinet assembly instructions PDF?

The official PDF is manual AA-2702649-1, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 703.321.24 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2702649-1. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example back-panel clip 10093081). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA EKET assembly guides · All bookcases & shelves assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained