IKEA EKET cabinet with 4 compartments assembly instructions
How to assemble the IKEA EKET cabinet with 4 compartments, step by step: 18 animated steps built from the official manual, about 45–60 min for 1 person, with drill with Ø 8 mm bit, screwdriver, spirit level, wall screws and plugs (not included).
White open EKET cabinet: four mitred panels and a cross divider that hook together without screws, a folding back panel held by clips, and wall fixing with adjustable spacers. Size: 70×35×70 cm (27 1/2×13 3/4×27 1/2"). About 45–60 min, 1 person. Tools: Drill with Ø 8 mm bit, Screwdriver, Spirit level, Wall screws and plugs (not included).
Based on the official IKEA manual AA-1914750-9 (PDF). Guide updated .
| Steps | 18 |
|---|---|
| Time | 45–60 min |
| People | 1 |
| Tools | Drill with Ø 8 mm bit, Screwdriver, Spirit level, Wall screws and plugs (not included) |
| Size | 70×35×70 cm (27 1/2×13 3/4×27 1/2") |
| Official manual | AA-1914750-9 |
| IKEA article number | 603.339.54 (white) |
| Pieces in the box | 41 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Side panel with pegs | 2 | |
| Top / bottom panel with keyhole slots | 2 | |
| Full-height divider | 1 | |
| Half shelf | 2 | |
| Folding back panel | 1 | |
| Back-panel clip | 10093081 | 12 |
| Clip pin | 10093082 | 12 |
| Wall spacer fitting | 141413 | 2 |
| Spacer knob | 141414 | 2 |
| Wall washer | 152651 | 2 |
| Cover cap | 152650 | 2 |
| Planning sheet AA-1908823 | 1 |
Steps
- Sort the four panels — Lay the 4 outer panels flat on a rug, inner side up. Two have small pegs at both mitred ends (they become the sides; one is marked “1”) and two have keyhole slots (top and bottom). Check: Work on a soft surface so the mitred edges do not get chipped.
- Hook the “1” panel onto a keyhole panel — Stand a keyhole panel on its front edge, back-panel groove at the top. Hold the panel marked “1” at a right angle to its end, push its 3 pegs into the wide part of the keyhole slots and press it down until it locks. Press the corner together. Check: The “1” and the grooves for the back panel are at the top edge, facing up.
- Hook the first half shelf onto the divider — Stand the long divider on its front edge. Hold a half shelf at a right angle to the middle of one face, push its 2 pegs into the keyhole slots and press it down until it locks.
- Hook the second half shelf on: a cross — Hook the second half shelf onto the other face of the divider in the same way, so the two half shelves line up and form a cross.
- Lower the cross into the corner — Lift the cross into the corner. Push the divider’s end pegs into the holes in the middle of the keyhole panel and the half shelf’s pegs into the middle of the “1” panel, then press the cross down until it locks.
- Hook on the second keyhole panel — Hook the second keyhole panel onto the free end of the “1” panel and the free end of the divider at the same time: pegs into the slots and holes, then press it down.
- Slide in the back panel — Open out the folded back panel. Slide it into the grooves from the open end, over the cross, all the way into the groove of the “1” panel. Check: The back panel must run inside the grooves, not on top of them.
- Close the frame with the last panel — Hook the last peg panel onto the open end: its pegs go into both keyhole panels and the half shelf’s pegs into its middle holes. Press it down until it locks.
- Tip it up, push the back panel down — Tip the cabinet up so it stands on the panel you fitted last, with the “1” at the top and the back facing you. Push the back panel down until its lower edge drops into the groove. Check: Check that the back panel sits in the groove and not on its edge.
- Clip the back panel all round — Push a clip (10093081) into each of the 12 holes behind the back panel, 3 along each edge. Press a pin (10093082) into each clip with your thumb so it locks. Then turn the cabinet a quarter turn so the “1” panel is at the side.
- Legs or wall rail: separate manuals — Fit the legs as their own manual shows (shown here). To hang the cabinet on the wall instead, use the EKET suspension rail and its own manual. Check: Legs and the suspension rail are separate products and are not in this box.
- Wall spacer fittings at the top corners — From the back, press a wall spacer fitting (141413) into the two holes near the top of each side panel, behind the back panel, with the threaded drum towards the middle.
- Drill through the fittings — Drill through the marked centre of each spacer fitting and the back panel with an 8 mm bit. With stacked EKET cabinets, only the top cabinet needs these holes.
- Screw on the knobs — If there is a skirting board, screw a knob (141414) onto each spacer fitting, clockwise, all the way in. Without a skirting board, leave the knobs off and push the cabinet straight against the wall. Check: Screw the knob on straight and fully, not at an angle.
- Against the wall, knobs out to the wall — Turn the cabinet round and push it back until the back legs touch the skirting board. Turn both knobs anticlockwise until they rest against the wall, so the cabinet stands straight. Check: Check with a spirit level; level the legs as their manual shows. To hang the cabinet on the wall instead, use the EKET suspension rail and the planning sheet (AA-1908823).
- Screw it to the wall from inside — From inside the two top compartments, put a washer (152651) over each drilled hole, the right way round as drawn, and screw through it into the wall. Check: Fix the cabinet to the wall to stop it tipping over. Wall screws and plugs are not included: choose ones that suit your wall.
- Cover caps — Press a cover cap (152650) onto each washer and turn it to lock it in place.
- Done! — Your EKET cabinet with 4 compartments is assembled and fixed to the wall. Max load: 7 kg per compartment shelf.
EKET cabinet with 4 compartments: questions and answers
How long does it take to assemble the IKEA EKET cabinet with 4 compartments?
About 45–60 min for 1 person, working through the 18 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the EKET cabinet with 4 compartments?
Drill with Ø 8 mm bit, screwdriver, spirit level, wall screws and plugs (not included).
Can one person assemble the EKET cabinet with 4 compartments?
Yes, it is a one-person build.
Does the EKET cabinet with 4 compartments need to be fixed to the wall?
The manual shows a wall fixing: see step 11 (Legs or wall rail: separate manuals) and step 12 (Wall spacer fittings at the top corners). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.
What size is the EKET cabinet with 4 compartments once assembled?
70×35×70 cm (27 1/2×13 3/4×27 1/2"), as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the EKET cabinet with 4 compartments?
33 fittings of 7 kinds, the most numerous being 12 × back-panel clip, 12 × clip pin, 2 × wall spacer fitting. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA EKET cabinet with 4 compartments assembly instructions PDF?
The official PDF is manual AA-1914750-9, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 603.339.54 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-1914750-9. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example back-panel clip 10093081). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA EKET cabinet assembly instructions
- IKEA EKET cabinet with 2 doors and 1 shelf assembly instructions
- IKEA EKET cabinet with 2 drawers assembly instructions
- IKEA BILLY bookcase assembly instructions
- IKEA KALLAX shelf unit 2x4 assembly instructions
- IKEA BESTÅ frame assembly instructions
- IKEA HYLLIS shelving unit (in/outdoor) assembly instructions
- IKEA LACK wall shelf assembly instructions
All IKEA EKET assembly guides · All bookcases & shelves assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained