IKEA STORKLINTA chest of 2 drawers assembly instructions
How to assemble the IKEA STORKLINTA chest of 2 drawers (dresser), step by step: 28 animated steps built from the official manual, about 1–1.5 hours for 1 person, with Phillips screwdriver, flat-blade screwdriver, pencil, drill and 8 mm bit (wall fixing).
A small white chest of 2 drawers that clicks together: pins drop into keyhole slots, the back slides into grooves, and the drawers run on wheeled runners. Size: 40x50x53 cm. About 1–1.5 hours, 1 person. Tools: Phillips screwdriver, Flat-blade screwdriver, Pencil, Drill and 8 mm bit (wall fixing).
Based on the official IKEA manual AA-2622470-5 (PDF). Guide updated .
| Steps | 28 |
|---|---|
| Time | 1–1.5 hours |
| People | 1 |
| Tools | Phillips screwdriver, Flat-blade screwdriver, Pencil, Drill and 8 mm bit (wall fixing) |
| Size | 40x50x53 cm |
| Official manual | AA-2622470-5 |
| IKEA article number | 006.314.14 (white) |
| Pieces in the box | 86 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Side panel | 2 | |
| Top | 1 | |
| Bottom | 1 | |
| Back panel | 1 | |
| Plinth | 1 | |
| Drawer front | 2 | |
| Drawer side | 4 | |
| Drawer back | 2 | |
| Drawer bottom | 2 | |
| Drawer runner set 10103402 (4 rails) | 2 | |
| Screw | 146114 | 24 |
| Back panel clip | 10093081 | 4 |
| Clip cap | 10093082 | 4 |
| Plastic plug | 151708 | 2 |
| Pin | 151707 | 2 |
| Angle bracket | 102553 | 2 |
| Screw | 105248 | 4 |
| Corner glide | 10101849 | 2 |
| Glide | 158568 | 2 |
| Cam bolt | 10120234 | 8 |
| Cam lock | 119030 | 8 |
| Wall bracket | 106989 | 1 |
| Screw | 109049 | 1 |
| Washer | 100823 | 2 |
| Wall screw | 109568 | 1 |
| Wall plug | 10087223 | 1 |
Steps
- Runners on the side panels — Lay both side panels on a soft surface, inside up. Screw 2 carcass runners to each panel with 3 screws 146114 each (bag 1): the runners marked CR go on the right-hand panel, CL on the left. The wheel end goes to the front edge, away from the groove. Check: The groove along one edge of each panel is for the back panel: it must be at the back.
- Bottom onto the left side panel — Stand the left side panel on its front edge, runners facing in. Hold the bottom against it, push its 2 pins into the keyhole slots in the panel, then press the bottom down until it clicks.
- Right side panel on — Stand the right side panel up on its front edge, runners facing in. Push its keyhole slots over the pins on the other end of the bottom and press the panel down until it clicks.
- Wall bracket on the top — Lay the top upside down. Put the wall bracket 106989 on it at the back edge, upright leg at the edge, and screw it on loosely through its slot with the washer 100823 and screw 109049 (wall-fixing bag). Check: Leave the screw a little loose for now: the bracket is pushed against the wall later.
- Top on — Turn the top over and hold it against the top edges of the side panels, with the bracket inside at the back. Push the keyhole slots over the pins in the panels and press the top towards the front edge until it clicks.
- Slide in the back panel — Slide the back panel into the grooves in the side panels from the open bottom end, over the back edge of the bottom, until it reaches the groove in the top. The round cut-out goes at the top, around the wall bracket.
- Clips on the back panel — Press 4 clips 10093081 into the notches along the side edges of the back panel, 2 on each side, then snap a cap 10093082 onto each clip.
- Fix the back panel to the bottom — At the bottom end, push a plastic plug 151708 through each of the 2 holes in the back panel into the edge of the bottom, then press a pin 151707 into each plug to lock it.
- Angle brackets on the plinth — Lay the plinth on its front. Put an angle bracket 102553 near each end, upright leg standing up, and fix each with a screw 105248.
- Turn it over, plinth on — Turn the frame over so it lies on its back. Put the plinth across the front edges at the bottom end, brackets inside, and screw each bracket to the side panel with a screw 105248.
- Glides — Press the 2 L-shaped glides 10101849 onto the bottom front corners, under the side panels and the plinth ends, and the 2 glides 158568 under the side panels near the back.
- Stand it against the wall — Stand the chest up on its glides and place it where it will stay, with its back against the wall.
- Bracket to the wall, mark — Reach in through the top opening. Loosen the bracket screw a little, slide the bracket back until its upright leg touches the wall, and mark the wall with a pencil through the slot.
- Move the chest away — Move the chest away from the wall so you can drill at the pencil mark.
- Choose the fixing for your wall — The screw and plug supplied suit most solid walls (A) and hollow walls (B). In solid wood (C), use the screw without the plug. If you are unsure, ask a hardware shop for the right fixing. Check: Drill bits: 8 mm for solid and hollow walls, 3 mm for solid wood.
- Drill the hole — Drill a hole at the pencil mark: 8 mm and about 70 mm deep in a solid wall, 8 mm in a hollow wall, or 3 mm in solid wood.
- Plug in the wall — Push the wall plug 10087223 into the hole until its collar is flat against the wall (not needed in solid wood).
- Fix it to the wall — Put the chest back against the wall. Through the slot in the bracket, drive the screw 109568 with a washer 100823 into the plug. Then tighten the bracket screw under the top. Check: Fixing the chest to the wall stops it tipping over. Do not skip it.
- Drawer 1: sides onto the front — Now the drawers (bag 2): build each one the same way. Stand a drawer front on its edge, inside towards you. Push the pins in the end of each drawer side into the keyhole slots in the front and press the side down until it clicks. Check: The grooves for the drawer bottom run along the bottom of the sides, facing in.
- Drawer bottom — Stand the drawer on its front (face down). Slide the drawer bottom down into the grooves in the sides until it sits in the groove in the front.
- Drawer back — Lay the drawer back between the sides at the open end, groove down over the edge of the drawer bottom.
- Cam bolts — Push 4 cam bolts 10120234 through the holes near the top of the sides into the ends of the drawer back, 2 on each side.
- Lock the back — Put 4 cam locks 119030 into the round holes in the drawer back, arrow towards the bolt, and turn each one clockwise with a flat screwdriver until it grips the bolt.
- Runners on the drawer — Stand the drawer up. Press a drawer runner onto the bottom edge of each side, wheel at the back, and fix each one with 3 screws 146114 (bag 2).
- Drawer 2: the same again — Put the first drawer aside and build the second one the same way: sides onto the front, bottom, back, 4 cam bolts and 4 cam locks, then the runners with 6 screws.
- Top drawer in — Take the drawer with the warning label inside: it goes in the top opening. Hold it in front of the opening, tilt the front up a little and set its back wheels on the runners. Slide it in, lower the front and push it all the way home. Check: The drawer with the warning label must go at the top.
- Bottom drawer in — Put the other drawer into the bottom opening the same way: tilt the front up, set the back wheels on the runners, slide it in and push it home.
- Done! — Your STORKLINTA chest of 2 drawers is finished and fixed to the wall. Keep the heaviest things in the bottom drawer.
STORKLINTA chest of 2 drawers: questions and answers
How long does it take to assemble the IKEA STORKLINTA chest of 2 drawers?
About 1–1.5 hours for 1 person, working through the 28 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the STORKLINTA chest of 2 drawers?
Phillips screwdriver, flat-blade screwdriver, pencil, drill and 8 mm bit (wall fixing).
Can one person assemble the STORKLINTA chest of 2 drawers?
Yes, it is a one-person build.
Does the STORKLINTA chest of 2 drawers need to be fixed to the wall?
The manual shows a wall fixing: see step 4 (Wall bracket on the top) and step 17 (Plug in the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.
What size is the STORKLINTA chest of 2 drawers once assembled?
40x50x53 cm, as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the STORKLINTA chest of 2 drawers?
68 fittings of 16 kinds, the most numerous being 24 × screw, 8 × cam bolt, 8 × cam lock. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA STORKLINTA chest of 2 drawers assembly instructions PDF?
The official PDF is manual AA-2622470-5, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 006.314.14 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2622470-5. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example drawer runner set 10103402). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA STORKLINTA chest of 6 drawers assembly instructions
- IKEA HEMNES 3-drawer dresser assembly instructions
- IKEA MALM chest of 3 drawers assembly instructions
- IKEA ALEX drawer unit assembly instructions
- IKEA LENNART drawer unit assembly instructions
- IKEA MALM dressing table assembly instructions
- IKEA BRIMNES bedside table assembly instructions
- IKEA ALEX drawer unit on castors assembly instructions
All IKEA STORKLINTA assembly guides · All dressers & drawers assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained