IKEA STORKLINTA chest of 6 drawers assembly instructions
How to assemble the IKEA STORKLINTA chest of 6 drawers (dresser), step by step: 40 animated steps built from the official manual, about 2.5–3.5 hours for 2 people, with Phillips screwdriver, flat-blade screwdriver, hammer, pencil, drill and 8 mm bit (wall fixing).
A wide white chest of 6 drawers that clicks together: pins drop into keyhole slots, folding backs slide into grooves, and an interlock lets only one drawer open at a time. Size: 140x50x75 cm. About 2.5–3.5 hours, 2 people. Tools: Phillips screwdriver, Flat-blade screwdriver, Hammer, Pencil, Drill and 8 mm bit (wall fixing).
Based on the official IKEA manual AA-2620325-5 (PDF). Guide updated .
| Steps | 40 |
|---|---|
| Time | 2.5–3.5 hours |
| People | 2 |
| Tools | Phillips screwdriver, Flat-blade screwdriver, Hammer, Pencil, Drill and 8 mm bit (wall fixing) |
| Size | 140x50x75 cm |
| Official manual | AA-2620325-5 |
| IKEA article number | 706.275.50 (white) |
| Pieces in the box | 249 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Side panel | 2 | |
| Middle panel | 1 | |
| Top | 1 | |
| Bottom | 2 | |
| Folding back panel | 2 | |
| Plinth | 2 | |
| Drawer front | 6 | |
| Drawer side | 12 | |
| Drawer back | 6 | |
| Drawer bottom | 6 | |
| Drawer runner set 10103402 (4 rails) | 6 | |
| Screw | 146114 | 72 |
| Back panel clip | 10093081 | 8 |
| Clip cap | 10093082 | 20 |
| Plastic plug | 151708 | 4 |
| Pin | 151707 | 4 |
| Angle bracket | 102553 | 4 |
| Screw | 105248 | 8 |
| Corner glide | 10101849 | 4 |
| Glide | 158568 | 3 |
| Interlock set 10136453 (box 10136645 + 6 clips 10125520) | 2 | |
| Screw | 100359 | 2 |
| Wire | 10040242 | 6 |
| Catch | 10133139 | 6 |
| Cam bolt | 10120234 | 24 |
| Cam lock | 119030 | 24 |
| Wall bracket | 106989 | 2 |
| Screw | 109049 | 2 |
| Washer | 100823 | 4 |
| Wall screw | 109567 | 2 |
| Wall plug | 10087223 | 2 |
Steps
- Runners on the panels — Lay the 3 panels on a soft surface. Screw 3 carcass runners to each with 3 screws 146114 per runner (bag 1): runners marked CR on the right side panel and on one face of the middle panel, CL on the left side panel. Wheel end to the front edge, away from the groove. Check: The groove along one long edge of each panel is for the back panels: it must be at the back.
- Runners on the middle panel's other face — Turn the middle panel over. Screw 3 runners marked CL to this face with 9 screws 146114, wheel ends at the front edge like on the other face.
- Left bottom onto the left side panel — Stand the left side panel on its front edge, runners facing in. Hold a bottom against it, push its 2 pins into the keyhole slots in the panel, then press the bottom down until it clicks.
- Middle panel on — Stand the middle panel up on its front edge, CL runners facing away from the bottom. Push its keyhole slots over the pins on the free end of the bottom and press the panel down until it clicks.
- Right bottom onto the middle panel — Hold the second bottom against the other face of the middle panel, push its pins into the keyhole slots and press it down until it clicks.
- Right side panel on — Stand the right side panel up on its front edge, runners facing in. Push its keyhole slots over the pins on the free end of the right bottom and press the panel down until it clicks.
- Wall brackets on the top — Lay the top upside down. Put the 2 wall brackets 106989 on it at the back edge, upright legs at the edge, and screw each on loosely through its slot with a washer 100823 and a screw 109049 (wall-fixing bag). Check: Leave the screws a little loose for now: the brackets are pushed against the wall later.
- Top on — Turn the top over and hold it against the top edges of the 3 panels, brackets inside at the back. Push the keyhole slots over the pins in the panels and press the top towards the front edge until it clicks.
- Slide in the back panels — Unfold a back panel and slide it into the grooves of the left opening from the open bottom end, over the bottom's back edge, until it reaches the groove in the top. The cut-out goes at the top, around the wall bracket. Do the same on the right.
- Fix the backs to the bottoms — At the bottom end, push a plastic plug 151708 through each of the 4 holes in the back panels into the back edges of the bottoms, then press a pin 151707 into each plug to lock it.
- Angle brackets on the plinths — Lay both plinths on their fronts. Put an angle bracket 102553 near each end of each plinth, upright leg standing up, and fix each with a screw 105248.
- Turn it over, plinths on — Turn the frame over so it lies on its back. Put the plinths across the front edges at the bottom end, brackets inside, and screw each bracket to its panel with a screw 105248. Check: Two people make turning the frame over easier.
- Glides — Press the 4 L-shaped glides 10101849 onto the bottom front corners, under the panels and the plinth ends (2 at the middle panel), and the 3 glides 158568 under the panels near the back.
- Interlock boxes — Lay an interlock box 10136645 on the back panel at the bottom end of each opening, against its right-hand panel, and screw its tab to the panel with a screw 100359.
- First interlock clips — Press the first clip 10125520 on each interlock cable into the holes just above its box, near the back edge of the panel.
- The other interlock clips — Run each cable up along the back edge and press its other 5 clips 10125520 into the holes, a pair above each runner: 10 clips in all.
- Clips on the back panels — Press 8 clips 10093081 into the notches along the side edges of the back panels, 2 on each edge, then snap a cap 10093082 onto each clip.
- Caps on the interlock clips — Snap a cap 10093082 onto each of the 12 interlock clips.
- Stand it against the wall — Stand the chest up on its glides and place it where it will stay, with its back against the wall. Check: Two people make standing the chest up easier.
- Brackets to the wall, mark — Reach in through the top openings. Loosen each bracket screw a little, slide the bracket back until its upright leg touches the wall, and mark the wall with a pencil through the slot: 2 marks.
- Move the chest away — Move the chest away from the wall so you can drill at the pencil marks.
- Choose the fixing for your wall — The screws and plugs supplied suit most solid walls (A) and hollow walls (B). In solid wood (C), use the screws without the plugs. If you are unsure, ask a hardware shop for the right fixing. Check: Drill bits: 8 mm for solid and hollow walls, 3 mm for solid wood.
- Drill the holes — Drill a hole at each pencil mark: 8 mm and about 70 mm deep in a solid wall, 8 mm in a hollow wall, or 3 mm in solid wood.
- Plugs in the wall — Push a wall plug 10087223 into each hole until its collar is flat against the wall (not needed in solid wood).
- Fix it to the wall — Put the chest back against the wall. Through the slot in each bracket, drive a screw 109567 with a washer 100823 into the plug. Then tighten both bracket screws under the top. Check: Fixing the chest to the wall stops it tipping over. Do not skip it.
- Drawer 1: sides onto the front — Now the 6 drawers (bag 2), all built the same way. Stand a drawer front on its edge, inside towards you. Push the pins in the end of each drawer side into the keyhole slots in the front and press the side down until it clicks. Check: The grooves for the drawer bottom run along the bottom of the sides, facing in.
- Drawer bottom — Stand the drawer on its front (face down). Slide the drawer bottom down into the grooves in the sides until it sits in the groove in the front.
- Wire on the drawer back — Lay the drawer back flat, outside up. Hammer the 2 legs of a wire 10040242 into the holes near its grooved edge until the wire sits flat on the panel. Check: Drive the legs all the way in.
- Drawer back — Lay the drawer back between the sides at the open end, wire outside, its groove down over the edge of the drawer bottom.
- Interlock catch — Push a catch 10133139 into the round hole near the back end of the right-hand drawer side, hook pointing up, until it snaps in.
- Cam bolts — Push 4 cam bolts 10120234 through the holes in the sides into the ends of the drawer back, 2 on each side.
- Lock the back — Put 4 cam locks 119030 into the round holes in the drawer back, arrow towards the bolt, and turn each one clockwise with a flat screwdriver until it grips the bolt.
- Runners on the drawer — Turn the drawer upside down onto the front's top edge. Press a drawer runner onto the edge of each side, wheel at the back, and fix each one with 3 screws 146114 (bag 2). Then roll the drawer over onto its runners.
- Drawers 2 and 3 — Build 2 more drawers the same way: sides onto the front, bottom, back with its wire, catch, 4 cam bolts and 4 cam locks, then upside down for the runners and 6 screws.
- Drawers 4 and 5 — Build the fourth and fifth drawers the same way, in a second row behind the first three.
- Drawer 6 — Build the last drawer the same way. Keep the 2 drawers with the warning label inside apart: they go in the top row.
- Top left drawer in — Take a drawer with the warning label inside: it goes in the top row. Hold it in front of the top left opening, tilt the front up a little and set its back wheels on the runners. Slide it in, lower the front and push it all the way home. Check: The drawers with the warning label must go in the top row.
- Top right and middle drawers in — Put the other labelled drawer into the top right opening the same way, then a drawer into the middle left opening: tilt the front up, set the back wheels on the runners, slide it in and push it home.
- The last drawers in — Put the last 3 drawers into the middle right, bottom right and bottom left openings the same way. Check: The interlock lets only one drawer open at a time: push a drawer fully shut before opening another.
- Done! — Your STORKLINTA chest of 6 drawers is finished and fixed to the wall. Keep the heaviest things in the bottom drawers.
STORKLINTA chest of 6 drawers: questions and answers
How long does it take to assemble the IKEA STORKLINTA chest of 6 drawers?
About 2.5–3.5 hours for 2 people, working through the 40 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the STORKLINTA chest of 6 drawers?
Phillips screwdriver, flat-blade screwdriver, hammer, pencil, drill and 8 mm bit (wall fixing).
Can one person assemble the STORKLINTA chest of 6 drawers?
It is planned as a 2-person build. One person can do most of it, but get help for steps 2, 4 and 6, where the furniture is lifted or turned.
Does the STORKLINTA chest of 6 drawers need to be fixed to the wall?
The manual shows a wall fixing: see step 7 (Wall brackets on the top) and step 24 (Plugs in the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.
What size is the STORKLINTA chest of 6 drawers once assembled?
140x50x75 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.
How many screws and fittings come with the STORKLINTA chest of 6 drawers?
201 fittings of 19 kinds, the most numerous being 72 × screw, 24 × cam bolt, 24 × cam lock. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA STORKLINTA chest of 6 drawers assembly instructions PDF?
The official PDF is manual AA-2620325-5, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 706.275.50 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2620325-5. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example drawer runner set 10103402). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA STORKLINTA chest of 2 drawers assembly instructions
- IKEA HEMNES 3-drawer dresser assembly instructions
- IKEA MALM chest of 3 drawers assembly instructions
- IKEA ALEX drawer unit assembly instructions
- IKEA LENNART drawer unit assembly instructions
- IKEA MALM dressing table assembly instructions
- IKEA BRIMNES bedside table assembly instructions
- IKEA ALEX drawer unit on castors assembly instructions
All IKEA STORKLINTA assembly guides · All dressers & drawers assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained