Step by StepAssembly Find your furniture

IKEA IDÅSEN cabinet with doors and drawers assembly instructions

How to assemble the IKEA IDÅSEN cabinet with doors and drawers, step by step: 45 animated steps built from the official manual, about 2–3 hours for 2 people, with Phillips screwdriver, flat-blade screwdriver, Allen key (included), wall screws (not included).

IKEA IDÅSEN cabinet with doors and drawers, assembled

A dark green steel office cabinet: two side frames joined on leg frames lying down, a fixed middle shelf and divider, two steel drawers built from hook-together panels, two shelves on clips and two doors on clip-on hinges. Size: 80×47×119 cm. About 2–3 hours, 2 people. Tools: Phillips screwdriver, Flat-blade screwdriver, Allen key (included), Wall screws (not included).

Based on the official IKEA manual AA-2091158-8 (PDF). Guide updated .

IDÅSEN cabinet with doors and drawers: quick facts
Steps45
Time2–3 hours
People2
ToolsPhillips screwdriver, Flat-blade screwdriver, Allen key (included), Wall screws (not included)
Size80×47×119 cm
Official manualAA-2091158-8
IKEA article number904.963.98 (dark green)
Pieces in the box123

In the box

PartPart numberQuantity
Side frame2
Leg frame (rail + 2 legs)2
Top1
Back panel2
Middle shelf1
Divider1
Drawer front2
Drawer side4
Drawer bottom2
Drawer back frame2
Shelf2
Door2
Screw19473220
Screw1939348
Screw1125818
Screw1937838
Screw1095358
Screw1066328
Washer1269162
Cover1333042
Shelf clip1145948
Allen key1128301
Handle1942114
Hinge plate1925554
Spacer1902322
Spacer knob1902332
Hinge1911172
Hinge1925272
Drawer runner1511272
Drawer runner1511282
Front fitting L1937372
Front fitting R1937362
Cable grommet1954651
Label holder1954662

Steps

  1. Hinge plates on the left side — Lay the left side frame flat on a soft surface, inner side up. Screw the 2 hinge plates (192555) onto the blocks near the front edge with 2 screws (193934) each. Check: Check that each plate sits straight, its arm square to the front edge, before you tighten the screws.
  2. Hinge plates on the right side — Lay the right side frame flat on a soft surface, inner side up. Screw the 2 hinge plates (192555) onto the blocks near the front edge with 2 screws (193934) each. Check: Check that each plate sits straight, its arm square to the front edge, before you tighten the screws.
  3. Stand the sides up, back legs in — Tip both side frames up onto their back edges, inner sides facing each other. Push the back leg frame (the rail with 2 legs, the tab in the middle facing up) into the bottom ends of the frames until it clicks.
  4. Front legs in — Push the front leg frame into the front corners at the bottom end of both side frames until it clicks.
  5. Slide in the top — At the other end, slide the top in between the side frames, its raised edge at the back, until its corners sit in the frames.
  6. Screw the top to the right side — Screw 2 screws (194732) through the holes near the top of the right side frame into the top.
  7. Screw the top to the left side — Do the same on the left side frame: 2 more screws (194732) into the top.
  8. Right back panel — Lay the right back panel into the cabinet against the right side frame, folded edges up, so its holes line up with the holes in the frame.
  9. Left back panel — Lay the left back panel in next to it, against the left side frame, holes lined up.
  10. Lock the back panels, right side — Press the back panels down. On the outside of the right side frame, push the 2 tabs in the slots by the back edge inwards with a flat screwdriver.
  11. Lock the back panels, left side — Push the 2 tabs on the outside of the left side frame inwards the same way. 4 tabs in all.
  12. Fixed middle shelf — Hold the middle shelf at an angle, front edge first, and hook its front corners into the side frames at the height of the lower hinge plates. Swing it down until it stands upright and its back edge clicks in.
  13. Drawer divider — Hold the divider at an angle and lower it into the middle of the drawer space, between the bottom rails and the middle shelf. Swing it straight so its bottom end sits against the tabs on both rails.
  14. Screw the divider, turn the cabinet — Fix the divider with 4 screws (194732): 2 through the tabs on the front and back rails, 2 through the middle shelf into its top end. Then turn the cabinet round on the floor.
  15. Left-hand runners (151127) — Push each 151127 runner into the drawer space from the front, along its wall, until the hook at its back end catches. Fix it with 2 screws (112581). One goes on the side frame, one on the divider.
  16. Right-hand runners (151128) — Push each 151128 runner into the drawer space from the front, along its wall, until the hook at its back end catches. Fix it with 2 screws (112581). One goes on the side frame, one on the divider.
  17. Stand the cabinet up — With a helper, tip the cabinet up onto its legs. Check: The cabinet is tall: always lift it with two people.
  18. Wall spacers (skirting board) — If a skirting board keeps the cabinet off the wall: press a spacer (190232) into the hole at the top of each side frame's back edge and screw a knob (190233) into it. With no skirting board, skip this and the knob turning.
  19. Against the wall — Push the cabinet back against the wall. Check: Fix the cabinet to the wall to stop it tipping over.
  20. Turn the spacers out — Turn the 2 spacer knobs out until they touch the wall, so the cabinet stands straight.
  21. Fix it to the wall — Inside, at the top of the back, screw a wall screw through a washer (126916) and the hole on each side into the wall. Click a cover (133304) onto each washer. Check: Wall screws are not included: use screws that suit your wall.
  22. Drawer: side and bottom — Stand a drawer side on its back end. Hold the drawer bottom against it, push its edge onto the hooks and slide it down until it locks.
  23. Drawer: second side — Push the other drawer side onto the free edge of the bottom and slide it down until it locks.
  24. Drawer: back frame — Lower the back frame into the box from the top, all the way down to the far end.
  25. Drawer: lock the frame — Push the tabs next to the frame inwards with a flat screwdriver: first the 2 on the left side and the 2 in the bottom.
  26. Drawer: lock the frame, other side — Then push in the 2 tabs on the right side. 6 tabs in all.
  27. Drawer: onto the drawer front — Lay the drawer front face down. Turn the box over, open side away from you, and lower it onto the front, inside the rim.
  28. Drawer: screw the front on — Fix the box to the drawer front with 6 screws (194732) through the holes by the front: 2 in each side, 2 in the bottom.
  29. Drawer: front fittings — Turn the drawer round. Screw the fitting marked R (193736) and the one marked L (193737) onto the front below the box, at the matching sides, with 2 screws (109535) each.
  30. Second drawer: the box — Build the second drawer box the same way: side, bottom, other side, back frame, then push its 6 tabs in.
  31. Second drawer: onto its front — Lower the second box onto its drawer front and fix it with 6 screws (194732).
  32. Second drawer: front fittings — Screw on its R (193736) and L (193737) fittings with 2 screws (109535) each, the same way.
  33. Label holders — Stand both drawers upright. Slide a label into each holder (195466), then click the holder into the square hole at the outer side of each drawer front. Check: The holder's back plate goes in with its hooks up, as shown.
  34. Drawer handles — Hold a handle (194211) against each drawer front, over the two holes in the middle.
  35. Screw the handles on — From inside each drawer, screw the handle on with 2 screws (106632).
  36. Slide the drawers in — Hold each drawer level in front of its opening, rest it on the runners and push it all the way in.
  37. Cable grommet — Press the cable grommet (195465) into the round hole at the back of the middle shelf.
  38. Shelf clips — Hook the 8 shelf clips (114594) into the slots at the front and back of both sides and press them down: 4 at the height for each shelf, all level.
  39. Upper shelf — Tip the first shelf, front edge up, into the cabinet above its clips, then lower it level onto the 4 clips.
  40. Lower shelf — Tip the second shelf, front edge up, into the cabinet above its clips, then lower it level onto the 4 clips.
  41. Top hinges on the doors — Lay both doors face down. Push a hinge (191117) into the pocket at the top of each door's hinge edge and fix it with 2 screws (193783) using the Allen key.
  42. Bottom hinges on the doors — Push a hinge (192527) into the pocket at the bottom of each door's hinge edge and fix it with 2 screws (193783) using the Allen key.
  43. Hang the doors — Hold each door open beside the cabinet and push its hinges onto the hinge plates until they click.
  44. Door handles, close the doors — Hold a handle (194211) on the front of each door near its free edge and screw it on from inside with 2 screws (106632). Then close the doors.
  45. Done! — Your IDÅSEN cabinet is assembled and fixed to the wall. The drawer fronts and the doors can be fine-tuned later with a screwdriver (manual pages 34-35).

IDÅSEN cabinet with doors and drawers: questions and answers

How long does it take to assemble the IKEA IDÅSEN cabinet with doors and drawers?

About 2–3 hours for 2 people, working through the 45 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the IDÅSEN cabinet with doors and drawers?

Phillips screwdriver, flat-blade screwdriver, Allen key (included), wall screws (not included). Already in the box: Allen key.

Can one person assemble the IDÅSEN cabinet with doors and drawers?

It is planned as a 2-person build. One person can do most of it, but get help for steps 3, 17 and 27, where the furniture is lifted or turned.

Does the IDÅSEN cabinet with doors and drawers need to be fixed to the wall?

The manual shows a wall fixing: see step 18 (Wall spacers (skirting board)) and step 21 (Fix it to the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the IDÅSEN cabinet with doors and drawers once assembled?

80×47×119 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the IDÅSEN cabinet with doors and drawers?

99 fittings of 21 kinds, the most numerous being 20 × screw, 8 × screw, 8 × screw. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA IDÅSEN cabinet with doors and drawers assembly instructions PDF?

The official PDF is manual AA-2091158-8, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 904.963.98 (dark green); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2091158-8. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example screw 194732). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All dressers & drawers assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained