IKEA VADHOLMA kitchen island assembly instructions
How to assemble the IKEA VADHOLMA kitchen island, step by step: 24 animated steps built from the official manual, about 1.5–2 hours for 2 people, with Phillips screwdriver, flat screwdriver.
Black solid-wood kitchen island with an oak worktop, two slatted shelves on the open side and room for stools behind the centre partition. Size: 126×79×90 cm. About 1.5–2 hours, 2 people. Tools: Phillips screwdriver, Flat screwdriver.
Based on the official IKEA manual AA-2085236-4 (PDF). Guide updated .
| Steps | 24 |
|---|---|
| Time | 1.5–2 hours |
| People | 2 |
| Tools | Phillips screwdriver, Flat screwdriver |
| Size | 126×79×90 cm |
| Official manual | AA-2085236-4 |
| IKEA article number | 203.591.54 (black oak) |
| Pieces in the box | 91 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| End frame (pre-assembled) | 2 | |
| Partition | 1 | |
| Slatted shelf | 2 | |
| Top rail | 1 | |
| Worktop | 1 | |
| Dowel | 101352 | 23 |
| Cam screw | 118331 | 8 |
| Screw | 128874 | 6 |
| Cam lock | 113434 | 8 |
| Barrel nut | 128406 | 8 |
| Sleeve nut | 117056 | 4 |
| Screw | 190473 | 4 |
| Bolt | 106918 | 8 |
| Bracket | 192372 | 4 |
| Screw | 105298 | 8 |
| Key holder | 121030 | 1 |
| Allen key | 100092 | 1 |
| Allen key | 100003 | 1 |
Steps
- Dowels into the partition — Lay the partition (the large black panel) flat on a rug or its cardboard. Push 3 dowels 101352 into each short end, 6 in total.
- Stand the partition in the first end frame — Lay one end frame flat, inside face up, with the leg that has 3 groups of 3 holes facing you. Stand the partition on one end, thick edge strip at the feet end, and lower it into the centre stile so the dowels go into their holes. Check: The partition's thick edge strip goes to the feet end of the frame, not to the top.
- Dowels into the 2 slatted shelves — Lay both slatted shelves down. Push 2 dowels 101352 into each end of the lower front rail, 4 per shelf and 8 in total.
- Middle shelf into the frame — With a helper holding the partition, stand the first shelf on its end: back rail against the partition, front rail in line with the middle group of holes in the frame leg. Lower it so its dowels go into the leg. Check: Two people needed. The barrel-nut hole in the front rail faces the feet end.
- 3 screws through the back rail — Fit the hex key into its holder. Drive 3 screws 128874 through the shelf's back rail into the partition, clockwise until tight.
- 2 brackets at the first frame — Hold a bracket 192372 in the corner between the partition and the frame. Screw 105298 into the partition, then a second one down into the frame. Fit the second bracket at the top end of the partition the same way.
- Bottom shelf into the frame — Stand the second shelf on its end the same way, at the feet end: back rail against the partition, dowels into the lowest group of holes in the leg. Check: Two people needed.
- 3 screws through the back rail — Drive 3 screws 128874 through the bottom shelf's back rail into the partition with the hex key, clockwise until tight.
- Dowels into the top rail — Push 2 dowels 101352 into each end of the front top rail, 4 in total.
- Top rail into the frame — Stand the top rail on its end at the open front corner and lower it so its dowels go into the top group of holes in the leg. Its barrel-nut holes face the feet end.
- Second end frame on top — Turn the second end frame over, inside face down, and lower it onto the top ends of the partition, shelves and rail so all the dowels go into their holes. Check: Two people needed.
- 4 barrel nuts and 4 bolts — Push 4 barrel nuts 128406 into the holes near the top frame, slot outwards, and line them up with a flat screwdriver. Then drive 4 bolts 106918 down through the frame into them with the hex key.
- Tip it over onto its top — With a helper, tip the unit over sideways so it lies upside down on the top ends of the frames, legs pointing up. Check: Two people needed.
- 4 barrel nuts and 4 bolts at the first frame — At the first frame, push 4 barrel nuts 128406 into their holes and line them up with the flat screwdriver. Drive 4 bolts 106918 through the frame into them with the hex key.
- 2 brackets at the second frame — At the second frame, fit 2 brackets 192372 in the corners between the partition and the frame: one screw 105298 into the partition, one into the frame.
- Turn it upright, 5 dowels on top — With a helper, turn the unit over onto its feet. Push 5 dowels 101352 into the top: 2 in each end frame and 1 in the middle of the front top rail. Check: Two people needed.
- 8 cam screws into the worktop — Lay the worktop upside down on a soft surface. Screw 8 cam screws 118331 into the pre-drilled holes in its underside, 4 at each end.
- Worktop on — With a helper, turn the worktop over and lower it straight onto the frame so the cam screws and dowels go into their holes. Check: Two people needed.
- Lock the worktop: left side — Push cam locks 113434 into the 2 holes in the outside of the left end frame and the 2 left holes in the partition, just under the worktop. Turn each one clockwise with a flat screwdriver until it locks.
- Lock the worktop: right side — Lock the other 4 the same way: 2 in the right end frame and 2 in the partition.
- Rail holes: 4 sleeve nuts from inside — Not fitting the VADHOLMA rail accessory? Close its 4 holes in the end frames (top and middle rail). Working from the open back, push a sleeve nut 117056 into each hole from inside and hold it with the small hex key 100003.
- Rail holes: screws at the left end — From outside the left end frame (as seen from the shelf side), screw a screw 190473 into each sleeve nut with the hex key, clockwise, while the small key holds the nut.
- Rail holes: screws at the right end — Do the same at the right end frame: 2 screws 190473 into the sleeve nuts, top and middle rail.
- Done! — Your VADHOLMA kitchen island is ready: slatted shelves on the open side and room for stools behind the partition. Oil the oak worktop now and then and wipe spills off straight away.
VADHOLMA kitchen island: questions and answers
How long does it take to assemble the IKEA VADHOLMA kitchen island?
About 1.5–2 hours for 2 people, working through the 24 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the VADHOLMA kitchen island?
Phillips screwdriver, flat screwdriver.
Can one person assemble the VADHOLMA kitchen island?
It is planned as a 2-person build. One person can do most of it, but get help for steps 11, 13 and 16, where the furniture is lifted or turned.
What size is the VADHOLMA kitchen island once assembled?
126×79×90 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.
How many screws and fittings come with the VADHOLMA kitchen island?
82 fittings of 11 kinds, the most numerous being 23 × dowel, 8 × cam screw, 8 × cam lock. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA VADHOLMA kitchen island assembly instructions PDF?
The official PDF is manual AA-2085236-4, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 203.591.54 (black oak); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2085236-4. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example dowel 101352). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA NISSAFORS trolley assembly instructions
- IKEA VESKEN trolley assembly instructions
- IKEA HORNAVAN trolley assembly instructions
- IKEA RÅSKOG trolley assembly instructions
- IKEA ÖVNING trolley assembly instructions
- IKEA TORNVIKEN kitchen island assembly instructions
- IKEA BROR trolley assembly instructions
- IKEA FÖRHÖJA kitchen trolley assembly instructions
All kitchen & carts assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained