Step by StepAssembly Find your furniture

IKEA ÖVNING trolley assembly instructions

How to assemble the IKEA ÖVNING trolley (cart), step by step: 30 animated steps built from the official manual, about 1 h for 1 person, with Phillips screwdriver, Allen key 10089605 (included).

IKEA ÖVNING trolley, assembled

A white trolley with open compartments, perforated grey-green steel panels and a steel tray with handles: two boxes are built lying down, joined, put on a castor base and topped with the tray. Size: 54x33 cm. About 1 h, 1 person. Tools: Phillips screwdriver, Allen key 10089605 (included).

Based on the official IKEA manual AA-2330633-2 (PDF). Guide updated .

ÖVNING trolley: quick facts
Steps30
Time1 h
People1
ToolsPhillips screwdriver, Allen key 10089605 (included)
Size54x33 cm
Official manualAA-2330633-2
IKEA article number005.170.03 (white grey green)
Pieces in the box97

In the box

PartPart numberQuantity
Low box: side panel1
Low box: back panel1
Low box: top1
Divider1
Tall box: back panel1
Tall box: side panel1
Tall box: top1
Base panel1
Shelf2
Perforated steel panel2
Tray long wall2
Tray end wall with handle2
Tray bottom1
Screw10022414
Dowel10134522
Shelf lock1199854
Shelf support1015588
Screw1010762
Screw14611316
Screw1557534
Screw1936804
Castor with brake100878472
Castor100724662
Allen key100896051
Hanging holder100908001

Steps

  1. Dowels in the low box panels — The low box is built first. Lay its side panel, back panel and top flat on a rug, then push the 10 dowels (101345) into the holes in their edges: 4 in the side panel, 4 in the back panel and 2 in the top. Check: Work on a rug or the cardboard so the panels don't get scratched.
  2. Shelf supports in the side panel — Press 2 shelf supports (101558) into the side panel, in the two holes on its inner face (the side with the dashed line in the drawing). Tighten the screw in each support with the screwdriver.
  3. Side panel onto the back panel — Stand the side panel on its long edge, shelf supports facing in, and push it onto the dowels in the left edge of the back panel. Check: The small hole in the middle of the side panel goes towards the back panel.
  4. Top of the low box — Stand the top on its edge at the other end of the back panel and push it onto the dowels in the end of the side panel. Its own 2 dowels point to the open side.
  5. Dowels in the tall box panels — Now the tall box. Lay the divider, the tall back panel, the tall side panel and the small top flat, then push 12 dowels (101345) into their edges: 4 in the divider, 4 in the back panel and 4 in the side panel. The top has none.
  6. Shelf supports, first face — Press 2 shelf supports (101558) into the divider and 2 into the tall side panel, in the holes on the dashed lines, and tighten the screw in each one.
  7. Turn the divider over — Turn the divider over and fit 2 more shelf supports (101558) on its other face, higher up, then tighten their screws. Check: The divider holds a shelf on each side, so it gets supports on both faces.
  8. Divider onto the back panel — Stand the divider on its long edge, the face with the last two supports facing right, and push it onto the dowels in the left edge of the tall back panel.
  9. Tall side panel — Stand the tall side panel on its long edge, shelf supports facing the divider, and push it onto the dowels in the other edge of the back panel.
  10. Top of the tall box — Stand the small top on its edge and push it onto the dowels in the ends of the divider and the side panel.
  11. Join the two boxes — Slide the low box up to the divider, its open side first, and push it onto the divider so its dowels go into the holes. Its top lines up with the tall box's second pair of supports.
  12. Screw the boxes together — From inside the tall box, screw 2 screws (100224) through the divider into the end of the low box's top, next to the shelf supports. Turn them in by hand, then tighten with the Allen key.
  13. First castor on the base — Lay the base panel upside down. Put a castor with a brake (10087847) on one corner of an end and fix it with 4 screws (146113) through the holes in its plate. Check: The 2 castors with a brake go at the same end, under the tall box.
  14. The other three castors — Fix the second castor with a brake next to it, then the 2 castors without a brake (10072466) at the other end, each with 4 screws (146113).
  15. Base onto the cabinet — Lift the base panel, castors outwards, and push it onto the dowels in the bottom ends of the side panels and the divider.
  16. Screw on the base — Screw 6 screws (100224) through the base into the side panels and the divider, 2 in each, by hand first, then tighten them with the Allen key.
  17. Stand the trolley up — Tip the trolley up onto its castors, open side to the front. Check: Lift it by the top end and let it roll back onto the wheels; don't drag it on its edge.
  18. Hook in the steel panels — Hold a perforated steel panel above the low box, at the back, and slide its 2 hooks into the holes in the divider, then let it drop down. Do the same with the second panel at the front.
  19. Screw down the steel panels — At the open end, screw 1 screw (100224) down through the foot of each steel panel into the top of the low box, then tighten with the Allen key.
  20. Tray walls — Set the 2 long tray walls up opposite each other, then slide the 2 end walls with the handles in between, so the flanges at their corners go inside the long walls and the nuts line up with the holes.
  21. Tray bottom — Lay the tray bottom in from above so it rests on the flanges along the bottom of the walls.
  22. Screw the tray corners — Screw a screw (155753) through each long wall into the nut on the end wall at all 4 corners, near the top. Check: Use the screws 155753 here, not the similar 101076.
  23. Tray onto the trolley — Lift the tray onto the trolley, lower its 4 tabs into the slots in the top and in the steel panels, then slide it towards the handle above the tall box until it stops.
  24. Screw the tray to the top — Above the tall box, screw 4 screws (100224) through the holes in the tray's corners into the top, then tighten each with the Allen key.
  25. Screw the tray to the steel panels — At the other end, screw 2 screws (101076) through the tray's corners into the top flanges of the steel panels.
  26. Shelves — Slide a shelf into the low box and one into the tall box, just above their 4 shelf supports, and lay each down on its supports. Check: The supports can be moved: both shelves can also go at the same height.
  27. Lock the left shelf — Hold a shelf lock (119985) against each side of the low box, just above the shelf, foot pointing down onto it, and fix it with a screw (193680). Check: The lock's foot must rest on the shelf. It stops the shelf from tipping up when you lift something off it.
  28. Lock the right shelf — Fix the other 2 shelf locks (119985) the same way on both sides of the tall box, just above its shelf, each with a screw (193680).
  29. Hanging holder — Hook the holder (10090800) into the holes of the tray, or anywhere else on the perforated steel. Check: To lock the 2 castors with a brake, press their pedals down; lift them to release.
  30. Done! — Your ÖVNING trolley is assembled. Lock the brakes on the two castors under the tall compartment to keep it in place.

ÖVNING trolley: questions and answers

How long does it take to assemble the IKEA ÖVNING trolley?

About 1 h for 1 person, working through the 30 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the ÖVNING trolley?

Phillips screwdriver, Allen key 10089605 (included). Already in the box: Allen key 10089605.

Can one person assemble the ÖVNING trolley?

Yes, it is a one-person build.

What size is the ÖVNING trolley once assembled?

54x33 cm, as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the ÖVNING trolley?

79 fittings of 11 kinds, the most numerous being 22 × dowel, 16 × screw, 14 × screw. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA ÖVNING trolley assembly instructions PDF?

The official PDF is manual AA-2330633-2, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 005.170.03 (white grey green); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2330633-2. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example screw 100224). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All kitchen & carts assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained