Step by StepAssembly Find your furniture

IKEA TORNVIKEN kitchen island assembly instructions

How to assemble the IKEA TORNVIKEN kitchen island, step by step: 36 animated steps built from the official manual, about 1.5–2.5 hours for 2 people, with Phillips screwdriver, flat screwdriver.

IKEA TORNVIKEN kitchen island, assembled

Kitchen island with an oak-veneer worktop, two open shelves on one side and knee space for bar stools on the other, built between two pre-assembled end frames. Size: 126×77×90 cm. About 1.5–2.5 hours, 2 people. Tools: Phillips screwdriver, Flat screwdriver.

Based on the official IKEA manual AA-2100799-5 (PDF). Guide updated .

TORNVIKEN kitchen island: quick facts
Steps36
Time1.5–2.5 hours
People2
ToolsPhillips screwdriver, Flat screwdriver
Size126×77×90 cm
Official manualAA-2100799-5
IKEA article number403.916.57 (off white oak)
Pieces in the box131

In the box

PartPart numberQuantity
End frame (pre-assembled)2
Partition1
Shelf2
Worktop1
Top board1
Top rail2
Shelf rail2
Bottom strip1
Cam screw11833129
Dowel10134538
Screw1003645
Short dowel1013482
Cam lock10343029
Angle bracket1027204
Glide1072714
Screw1139288

Steps

  1. Dowels into the partition — Lay the partition (the large white panel) flat on a soft surface. Push 3 dowels 101345 into each short end, 6 in total.
  2. 8 cam screws into the partition — Screw 8 cam screws 118331 into the holes in the top face of the partition, two rows of 4, with a Phillips screwdriver. Stop when the collar meets the board.
  3. Dowels into the 2 shelves — Push 5 dowels 101345 into each oak shelf: 3 in the long edge without notches and 1 in each end next to the notch. Then turn both shelves over.
  4. Stand the shelves onto the partition — Stand both shelves on their dowel edge and press them down onto the partition, guiding the dowels and cam screws into the holes. The notched corners point away from the partition.
  5. 8 cam locks into the shelves — Put 8 cam locks 103430 into the holes in the shelves next to the partition, 4 per shelf, arrow towards the cam screw. Turn each one clockwise with a flat screwdriver until it locks.
  6. 7 cam screws into the first end frame — Lay one end frame on the floor, inside face up, legs pointing to the right. Screw in 7 cam screws 118331: 3 in one leg, 1 in the other leg, 1 each in the top rail, middle stile and bottom rail.
  7. Stand it on end, frame on top — With a helper, stand the partition and shelves up on one end. Turn the end frame over and lower it onto the top ends so the cam screws and dowels go into their holes. The leg with 3 cam screws goes on the shelf side. Check: Two people needed.
  8. 3 cam locks under the frame — Lock the frame with 3 cam locks 103430 from the open shelf side: one in the partition and one in each shelf, next to the frame. Turn them clockwise with a flat screwdriver.
  9. Tip it over onto its top edges — With a helper, tip the unit over sideways so it lies upside down on its top edges, the frame legs pointing up. Check: Two people needed.
  10. Dowels into the top board — Push 2 dowels 101345 into each end of the narrow top board (4 in total).
  11. Slide the top board into the frame — Lay the top board next to the partition on the knee side, countersunk holes facing up, and slide it into the end frame so its dowels go into the top rail. Check: The countersunk screw holes must face up.
  12. Dowels into the knee-side top rail — Push one dowel 101345 into each end of the top rail for the knee side (the rail with the cam-lock holes near its ends).
  13. Slide the rail in along the board — Lay the top rail on its edge along the outside of the top board and slide it into the end frame, dowel into the leg.
  14. 1 cam lock in the rail — Put a cam lock 103430 into the hole near the end frame and turn it clockwise with a flat screwdriver.
  15. Short dowels into the bottom strip — Push 2 short dowels 101348 into the face of the bottom strip. Check: Use the short dowels 101348 here, not the long 101345.
  16. Bottom strip onto the partition — Lift the strip over the end frame and line it up with the free (bottom) edge of the partition, dowels towards it. Push it on so the dowels go into the partition.
  17. 3 screws through the partition — From the shelf side, drive 3 screws 100364 through the partition into the bottom strip with a Phillips screwdriver. Then turn the unit round so the shelves face you.
  18. Dowels into the top rail — Push one dowel 101345 into each end of the second top rail.
  19. Top rail into the frame — On the shelf side, line the rail up along the open side at the top (on the floor) and slide it into the end frame leg.
  20. Dowels into the middle shelf rail — Push one dowel 101345 into each end of a shelf rail. Check the holes in its ends against the drawing: the cam-lock hole must be the right distance from the end. Check: The two shelf rails look alike: pick the one whose end holes match the drawing.
  21. Rail along the middle shelf — Fit the rail along the front edge of the middle shelf and slide it into the end frame leg.
  22. Dowels into the other shelf rail — Push one dowel 101345 into each end of the second shelf rail, again checking its end holes against the drawing.
  23. Rail along the bottom shelf — Fit it along the front edge of the bottom shelf (at the top while upside down) and slide it into the leg.
  24. 3 cam locks in the rails — Put a cam lock 103430 into each of the 3 rails next to the end frame and turn them clockwise with a flat screwdriver.
  25. 7 cam screws into the second frame — Lay the second end frame inside face up next to the open end and screw in its 7 cam screws 118331, just like the first one.
  26. Swing the frame up and push it on — Swing the end frame up on its edge, legs pointing up like the first one, and push it onto the open end so all dowels and cam screws go into their holes.
  27. 7 cam locks at the second frame — Put 7 cam locks 103430 into the holes next to the second frame (partition, 2 shelves, 4 rails) and turn them clockwise.
  28. 4 brackets under the shelves — Fix 2 angle brackets 102720 under each shelf, tight against the partition: 1 screw 113928 into the shelf, 1 into the partition. Keep the oval hole as the drawing shows.
  29. Glides into the legs — Press a glide 107271 into the hole in the end of each of the 4 legs.
  30. Turn it upright, 10 dowels on top — With a helper, lift the unit and turn it over onto its glides. Push 10 dowels 101345 into the top edges: 3 in the knee-side rail, 3 in the partition, 2 in the shelf-side rail and 1 in each end frame. Check: Two people needed.
  31. 7 cam screws into the worktop — Lay the worktop upside down on a soft surface and screw 7 cam screws 118331 into the pre-drilled holes in its underside.
  32. Worktop on — With a helper, turn the worktop over and lower it straight onto the frame so the cam screws and dowels go into their holes. Check: Two people needed.
  33. Lock the worktop: front and left end — Push cam locks 103430 into the holes just under the worktop: 2 in the left end frame and 1 in the shelf-side rail. Turn each one clockwise with a flat screwdriver.
  34. Lock the worktop: right end and knee side — Lock the other 4 the same way: 2 in the right end frame, 1 in the knee-side rail and 1 in the partition (reach in under the top board).
  35. 2 screws up into the worktop — On the knee side, drive 2 screws 100364 up through the countersunk holes in the top board into the worktop with a Phillips screwdriver.
  36. Done! — Your TORNVIKEN kitchen island is ready: open shelves on one side, room for bar stools on the other. Wipe spills off the oak worktop straight away.

TORNVIKEN kitchen island: questions and answers

How long does it take to assemble the IKEA TORNVIKEN kitchen island?

About 1.5–2.5 hours for 2 people, working through the 36 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the TORNVIKEN kitchen island?

Phillips screwdriver, flat screwdriver.

Can one person assemble the TORNVIKEN kitchen island?

It is planned as a 2-person build. One person can do most of it, but get help for steps 7, 9 and 16, where the furniture is lifted or turned.

What size is the TORNVIKEN kitchen island once assembled?

126×77×90 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the TORNVIKEN kitchen island?

119 fittings of 8 kinds, the most numerous being 38 × dowel, 29 × cam screw, 29 × cam lock. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA TORNVIKEN kitchen island assembly instructions PDF?

The official PDF is manual AA-2100799-5, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 403.916.57 (off white oak); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2100799-5. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example cam screw 118331). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA TORNVIKEN assembly guides · All kitchen & carts assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained