Step by StepAssembly Find your furniture

IKEA TORNVIKEN wall shelf assembly instructions

How to assemble the IKEA TORNVIKEN wall shelf, step by step: 17 animated steps built from the official manual, about 1–1.5 hours for 1 person, with Phillips screwdriver, flat screwdriver, spirit level, wall screws (not included).

IKEA TORNVIKEN wall shelf, assembled

Off-white wall shelf with shaped brackets and a hanging rail with 6 S-hooks: the frame is built standing on end, then turned upside down onto the shelf top and screwed to the wall. Size: 120 cm. About 1–1.5 hours, 1 person. Tools: Phillips screwdriver, Flat screwdriver, Spirit level, Wall screws (not included).

Based on the official IKEA manual AA-2106889-5 (PDF). Guide updated .

TORNVIKEN wall shelf: quick facts
Steps17
Time1–1.5 hours
People1
ToolsPhillips screwdriver, Flat screwdriver, Spirit level, Wall screws (not included)
Size120 cm
Official manualAA-2106889-5
IKEA article number603.916.61 (off white)
Pieces in the box49

In the box

PartPart numberQuantity
Screw1003478
Dowel10134515
Cam screw11833110
Cam lock11925010
S-hook1944136

Steps

  1. Screw the L-profile to the front board — Lay the narrow front board flat on a rug. Place the steel L-profile along it, flat side on the board and the upright side along one long edge, and fix it with 5 screws (100347) through the round holes.
  2. Cam screws in both brackets — Lay both shaped brackets flat, inside face up. Screw 2 cam screws (118331) into each one, 4 in total. Turn them in until the collar sits on the surface, not sunk into it. Check: Do not screw the cam screws too deep: the collar must rest on the board.
  3. Stand the front board on a bracket — Push a dowel (101345) into each end of the front board. Stand the board on end on one bracket so the lower dowel and the cam screw go into its end, with the L-profile facing you.
  4. Lock the front board — Put a cam lock (119250) into the hole near the lower end of the front board, arrow towards the board end. Turn it clockwise with a flat screwdriver to pull the board tight onto the bracket.
  5. Stand the wall board on the bracket — Push 2 dowels (101345) into each end of the wide wall board, 4 in total. Stand it on end on the same bracket, behind the front board, so its lower dowels and cam screw go into the bracket.
  6. Lock the wall board — Put a cam lock (119250) into the hole near the lower end of the wall board, on its outer face. Turn it clockwise with the flat screwdriver until the board is pulled tight onto the bracket.
  7. Put in the hanging rail — Lower the round rail between the two boards and push its end into the hole in the bracket.
  8. Slide on the 6 S-hooks — Thread the 6 S-hooks (194413) onto the rail from the top, ring first. Check every hook faces the way shown, not reversed.
  9. Put the second bracket on top — Turn the second bracket over, cam screws facing down, and lower it onto the top ends of the boards so the dowels, cam screws and the rail end go into its holes.
  10. Lock the top bracket — Put a cam lock (119250) into the hole near the upper end of each board, 2 in total, and turn them clockwise with the flat screwdriver to lock the boards to the top bracket.
  11. Dowels in the top edges — Push 9 dowels (101345) into the edges that will meet the shelf top: 5 in the wall board, 2 in the front board and 1 in each bracket.
  12. Cam screws in the shelf top — Lay the shelf top upside down on a rug. Screw 6 cam screws (118331) into its underside: 4 in the row along the back edge and 1 at each end of the front row. Stop when the collar touches the board. Check: Do not screw the cam screws too deep: the collar must rest on the board.
  13. Turn the frame onto the shelf top — Tip the frame over so it is upside down and lower it straight onto the shelf top, wall board along the edge with 4 cam screws. The dowels and cam screws go into the boards and brackets. Check: Two people make this easier.
  14. Lock the shelf top — Put 6 cam locks (119250) into the holes along the shelf top: 4 in the outer face of the wall board and 2 inside the front board near its ends. Turn each one clockwise with the flat screwdriver.
  15. Screw the L-profile to the shelf — Inside the frame, drive 3 screws (100347) through the slotted holes in the flat side of the L-profile into the shelf top.
  16. Screw the shelf to the wall — Turn the shelf upright and hold it against the wall, level it with a spirit level, then fix it with 3 screws through the holes in the wall board. Use pan-head screws suited to your wall; they are not included. Check: Wall screws are not included: choose ones that suit your wall. Use pan-head screws, not countersunk ones.
  17. Done! — Your TORNVIKEN wall shelf is up, with 6 S-hooks on the rail for utensils or mugs. Max load: 16 kg, spread evenly.

TORNVIKEN wall shelf: questions and answers

How long does it take to assemble the IKEA TORNVIKEN wall shelf?

About 1–1.5 hours for 1 person, working through the 17 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the TORNVIKEN wall shelf?

Phillips screwdriver, flat screwdriver, spirit level, wall screws (not included).

Can one person assemble the TORNVIKEN wall shelf?

Yes, it is a one-person build.

What size is the TORNVIKEN wall shelf once assembled?

120 cm, as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the TORNVIKEN wall shelf?

49 fittings of 5 kinds, the most numerous being 15 × dowel, 10 × cam screw, 10 × cam lock. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA TORNVIKEN wall shelf assembly instructions PDF?

The official PDF is manual AA-2106889-5, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 603.916.61 (off white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2106889-5. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example screw 100347). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA TORNVIKEN assembly guides · All bookcases & shelves assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained