IKEA RÅSKOG trolley assembly instructions
How to assemble the IKEA RÅSKOG trolley (cart), step by step: 9 animated steps built from the official manual, about 30 min for 1 person, with Phillips screwdriver, spanner 130772 (included).
A white steel trolley with three deep baskets: two tube leg frames are screwed onto a U-shaped base, each basket is bolted between them and four castors screw into the corners. Size: 35x45x77 cm. About 30 min, 1 person. Tools: Phillips screwdriver, Spanner 130772 (included).
Based on the official IKEA manual AA-2475409-4 (PDF). Guide updated .
| Steps | 9 |
|---|---|
| Time | 30 min |
| People | 1 |
| Tools | Phillips screwdriver, Spanner 130772 (included) |
| Size | 35x45x77 cm |
| Official manual | AA-2475409-4 |
| IKEA article number | 305.867.83 (white) |
| Pieces in the box | 40 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Upper leg section | 2 | |
| Middle leg section (tabs at both ends) | 2 | |
| U-shaped base tube | 2 | |
| Basket | 3 | |
| Clamp plate | 6 | |
| Screw | 121194 | 8 |
| Carriage bolt | 124154 | 6 |
| Cap nut | 10119612 | 6 |
| Castor with brake | 10121215 | 2 |
| Castor | 10121224 | 2 |
| Spanner | 130772 | 1 |
Steps
- Join the leg sections — Stand the two middle leg sections up, the tab that sticks out past the tube ends at the bottom. Push an upper section down into each one, then fix every joint with 2 screws (121194) driven into the holes on the inner side of the tubes. Check: The middle sections have a tab at both ends. The one that reaches past the tube ends goes at the bottom.
- Fit the legs onto the base — Set the two U-shaped base tubes on the floor so their four stubs point up. Push each leg down over its two stubs, then fix every joint with 2 screws (121194) from the inner side.
- Bottom basket: left side — Lower the first basket between the legs to the lowest tabs (marked 1), its rim around the tubes. Put a clamp plate around the outside of the two tubes, push a carriage bolt (124154) through the plate, the tab and the end of the basket, and screw a cap nut (10119612) onto it inside the basket. Tighten the nut with the spanner. Check: Check the number next to the tab: 1 for the bottom basket, 2 for the middle one, 3 for the top one.
- Bottom basket: right side — Fix the other end of the basket the same way: clamp plate around the outside of the tubes, carriage bolt through, cap nut inside, tightened with the spanner. Check: The bolt has a square neck that sits in the clamp plate, so only the nut turns.
- Bolt in the middle basket — Lower the second basket to the tabs marked 2 and fix it the same way: clamp plates outside, carriage bolts through, cap nuts inside, tightened with the spanner.
- Bolt in the top basket — Lower the last basket to the top tabs, marked 3, and fix it with the last 2 clamp plates, bolts and cap nuts.
- Castors with brake — Lay the trolley on its back on a rug or the cardboard. Screw the 2 castors with a brake into the holes at the corners of one end of the base, then tighten them with the open end of the spanner. Check: Lay the trolley on something soft so the powder coat doesn't get scratched.
- Other castors, then stand it up — Screw the 2 castors without a brake into the corners at the other end, by hand, until they are tight. Then stand the trolley up on its wheels. Check: To lock a castor, press its brake lever down. Lift the lever to release it.
- Done! — Your RÅSKOG trolley is assembled. Press the brake levers down to keep it in place.
RÅSKOG trolley: questions and answers
How long does it take to assemble the IKEA RÅSKOG trolley?
About 30 min for 1 person, working through the 9 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the RÅSKOG trolley?
Phillips screwdriver, spanner 130772 (included). Already in the box: Spanner 130772.
Can one person assemble the RÅSKOG trolley?
Yes, it is a one-person build.
What size is the RÅSKOG trolley once assembled?
35x45x77 cm, as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the RÅSKOG trolley?
24 fittings of 5 kinds, the most numerous being 8 × screw, 6 × carriage bolt, 6 × cap nut. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA RÅSKOG trolley assembly instructions PDF?
The official PDF is manual AA-2475409-4, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 305.867.83 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2475409-4. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example screw 121194). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA NISSAFORS trolley assembly instructions
- IKEA VESKEN trolley assembly instructions
- IKEA HORNAVAN trolley assembly instructions
- IKEA ÖVNING trolley assembly instructions
- IKEA TORNVIKEN kitchen island assembly instructions
- IKEA BROR trolley assembly instructions
- IKEA FÖRHÖJA kitchen trolley assembly instructions
- IKEA BEKVÄM kitchen trolley assembly instructions
All kitchen & carts assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained