IKEA BEKVÄM kitchen trolley assembly instructions
How to assemble the IKEA BEKVÄM kitchen trolley (cart), step by step: 15 animated steps built from the official manual, about 45–60 min for 1 person, with Phillips screwdriver, flat screwdriver, awl, adjustable wrench.
Solid beech kitchen trolley: a worktop on an apron frame, four legs, two slatted shelves and two castors. Size: 58×50×85 cm. About 45–60 min, 1 person. Tools: Phillips screwdriver, Flat screwdriver, Awl, Adjustable wrench.
Based on the official IKEA manual AA-30370-10 (PDF). Guide updated .
| Steps | 15 |
|---|---|
| Time | 45–60 min |
| People | 1 |
| Tools | Phillips screwdriver, Flat screwdriver, Awl, Adjustable wrench |
| Size | 58×50×85 cm |
| Official manual | AA-30370-10 |
| IKEA article number | 702.403.51 (beech) |
| Pieces in the box | 81 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Worktop | 1 | |
| Apron rail, long | 2 | |
| Apron rail, short | 2 | |
| Leg with plain end | 2 | |
| Leg with tapered foot | 2 | |
| Slatted shelf | 2 | |
| Threaded rod | 100033 | 4 |
| Barrel nut | 100535 | 4 |
| Nut | 100712 | 4 |
| Washer | 100833 | 4 |
| Wooden dowel | 101351 | 4 |
| Corner bracket | 102652 | 4 |
| Angle bracket | 102720 | 4 |
| Screw | 108530 | 8 |
| Screw | 109041 | 24 |
| Castor | 113358 | 2 |
| Cam lock | 113434 | 4 |
| Cam screw | 118331 | 4 |
Steps
- Angle brackets on the long rails — Lay the four apron rails flat, inner face up. On each long rail fix 2 angle brackets 102720 with a short screw 109041 each, upright leaf at the long edge. Use a Phillips screwdriver. Take care: the longer screws 108530 are for the castors. Check: Use the short screws 109041 here, not 108530.
- Apron frame with corner brackets — Stand the four rails up as a frame, angle brackets at the bottom edge. Fit a corner bracket 102652 across each corner, its bent ends in the grooves of the rails, and fix it with 4 screws 109041. Check: Use the short screws 109041 here, not 108530.
- Frame onto the worktop — Lay the worktop upside down on a soft surface. Lift the frame onto it, angle brackets down, so it sits evenly inside the edge all round. Fix the 4 angle brackets to the worktop with 4 screws 109041. Check: Use the short screws 109041 here, not 108530.
- Cam screws into the legs — Lay the four legs side by side. Screw a cam screw 118331 into the hole near the foot end of each leg, on the face with the two holes, by hand until it stops.
- Barrel nuts and threaded rods — Push a barrel nut 100535 into the hole in the top end of each leg, slot outwards. Screw a threaded rod 100033 into the hole on the corner edge until it grips the barrel nut. Line the nut up with a flat screwdriver if the rod won't go in.
- First plain leg — Take one of the two legs with a plain end (not a tapered one). Stand it in a corner of the frame, its threaded rod through the corner bracket. Put on a washer 100833 and a nut 100712 and tighten with the wrench. Check: Use the legs with plain ends here: the tapered legs come later.
- Second plain leg — Fit the other leg with a plain end in the next corner on the same side, the same way: rod through the corner bracket, washer 100833 and nut 100712, tightened with the wrench.
- Tip it over — Carefully tip the trolley over onto the two legs you have just fitted, so the worktop stands on its edge.
- Both shelves in — Push 2 dowels 101351 into the ends of the shelf that goes in the middle and lower it onto the holes in the legs. Lower the second shelf onto the cam screws at the foot ends of the legs.
- Cam locks: lower shelf — Push 2 cam locks 113434 into the holes in the underside of the lower shelf, next to the legs, arrow towards the cam screw. Turn each one clockwise with a flat screwdriver to lock it.
- Tapered legs on top — Push 2 dowels 101351 into the free ends of the middle shelf. Hook the threaded rod of a tapered leg through its corner bracket, then lower the leg onto the dowel and cam screw. Do the same with the second tapered leg.
- Back upside down, nuts on — Turn the trolley back so it stands upside down on the worktop. Put a washer 100833 and a nut 100712 on each of the last two threaded rods and tighten them with the wrench.
- Cam locks: tapered legs — Push the last 2 cam locks 113434 into the holes in the lower shelf next to the tapered legs. Turn each one clockwise with a flat screwdriver to lock it.
- Castors — Set a castor 113358 on the end of each plain leg, wheel turned as shown. Prick the 8 screw holes through the plate with the awl, then fix each castor with 4 screws 108530. Check: Use the long screws 108530 here, not 109041. Turn the castor so the wheel runs as shown in the manual.
- Done! — Turn the trolley over onto its castors and tapered feet. Your BEKVÄM kitchen trolley is ready: lift the tapered end to roll it.
BEKVÄM kitchen trolley: questions and answers
How long does it take to assemble the IKEA BEKVÄM kitchen trolley?
About 45–60 min for 1 person, working through the 15 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the BEKVÄM kitchen trolley?
Phillips screwdriver, flat screwdriver, awl, adjustable wrench.
Can one person assemble the BEKVÄM kitchen trolley?
Yes, it is a one-person build.
What size is the BEKVÄM kitchen trolley once assembled?
58×50×85 cm, as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the BEKVÄM kitchen trolley?
70 fittings of 12 kinds, the most numerous being 24 × screw, 8 × screw, 4 × threaded rod. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA BEKVÄM kitchen trolley assembly instructions PDF?
The official PDF is manual AA-30370-10, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 702.403.51 (beech); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-30370-10. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example threaded rod 100033). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA BEKVÄM step stool assembly instructions
- IKEA NISSAFORS trolley assembly instructions
- IKEA VESKEN trolley assembly instructions
- IKEA HORNAVAN trolley assembly instructions
- IKEA RÅSKOG trolley assembly instructions
- IKEA ÖVNING trolley assembly instructions
- IKEA TORNVIKEN kitchen island assembly instructions
- IKEA BROR trolley assembly instructions
All IKEA BEKVÄM assembly guides · All kitchen & carts assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained