IKEA IDANÄS cabinet with bi-folding doors assembly instructions
How to assemble the IKEA IDANÄS cabinet with bi-folding doors, step by step: 47 animated steps built from the official manual, about 2–3 h for 2 people, with Phillips screwdriver, hammer, pencil, drill, spirit level, Allen key (included).
A white cabinet on legs with two folding doors and four shelves: the carcass clicks together lying down, the back panels slide in upside down, it stands on a separate leg frame and is fixed to the wall before the bi-fold doors are hung. Size: 121×50×135 cm. About 2–3 h, 2 people. Tools: Phillips screwdriver, Hammer, Pencil, Drill, Spirit level, Allen key (included).
Based on the official IKEA manual AA-2215723-14 (PDF). Guide updated .
| Steps | 47 |
|---|---|
| Time | 2–3 h |
| People | 2 |
| Tools | Phillips screwdriver, Hammer, Pencil, Drill, Spirit level, Allen key (included) |
| Size | 121×50×135 cm |
| Official manual | AA-2215723-14 |
| IKEA article number | 204.588.23 (white) |
| Pieces in the box | 182 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Side panel | 2 | |
| Bottom panel | 1 | |
| Top panel | 1 | |
| Top rail | 1 | |
| Divider | 1 | |
| Shelf | 4 | |
| Back panel | 2 | |
| Centre leg | 1 | |
| Leg piece | 2 | |
| Leg rail | 2 | |
| Door leaf | 4 | |
| Door track | 192163 | 2 |
| Gap strip | 10055242 | 2 |
| Pin | 151705 | 8 |
| Plug | 151706 | 8 |
| Clip | 10093081 | 8 |
| Wedge | 10093082 | 8 |
| Shelf pin | 131372 | 16 |
| Screw | 100347 | 4 |
| Allen key | 100001 | 1 |
| Screw | 100217 | 1 |
| Screw | 100214 | 1 |
| Screw | 10093458 | 4 |
| Dowel | 101352 | 9 |
| Angle bracket | 102553 | 2 |
| Adjustable foot | 131399 | 5 |
| Butt hinge | 10042027 | 4 |
| Screw | 150769 | 16 |
| Cup hinge | 175136 | 2 |
| Cup hinge | 152517 | 2 |
| Track fitting | 10050531 | 2 |
| Track fitting | 10050552 | 2 |
| Door stop | 10050549 | 2 |
| Pin | 192158 | 12 |
| Plug | 10075558 | 10 |
| Pin | 10051084 | 10 |
| Knob | 10041120 | 4 |
| Screw | 119976 | 4 |
| Wall fitting | 150688 | 2 |
| Adjuster knob | 150689 | 2 |
| Screw | 147968 | 2 |
| Washer | 126916 | 2 |
| Plug | 121714 | 2 |
| Cap | 10005905 | 2 |
Steps
- Bottom panel to a side panel — Lay a side panel on its back edge on a rug. Slide the bottom panel against its lower end so the 2 click-in dowels in the bottom panel go into the keyhole slots, then press the bottom panel down until it locks. Check: Work on a soft surface to protect the panels.
- Second side panel — Fit the other side panel on the free end of the bottom panel the same way: dowels into the 2 slots, then press the side panel down so it locks.
- Centre leg — Push a dowel (101352) into the outside of the bottom panel and fit the centre leg on it. From inside, fix it with the screw 100214 (the middle-length one) and the Allen key (100001). Check: Check the screw: 100214 here, not the shorter 100217 or the long 10093458.
- Divider — Lower the divider into the middle of the box. Slide it towards the bottom panel so its 2 fittings go into the keyhole slots, then press it down to lock.
- Dowels in the top rail — Push 2 wooden dowels (101352) into the holes in each end of the top rail: 4 dowels.
- Top rail — Lift the top rail in between the side panels at their upper end, along the front edges, and push its dowels into the holes. The groove in the rail faces the bottom of the cabinet. Check: Check the groove direction before you fit the rail: it will hold the door track.
- Top panel — Slide the top panel on to the upper ends of the side panels so its 6 click-in dowels go into the slots, keep it square to the sides, then press it down to lock.
- Screw the top to the divider — Fix the top panel to the divider with the short screw (100217) and the Allen key.
- Stand it on its top — With a helper, tip the cabinet over its top end so it stands upside down on the top panel, back facing you. Check: Two people are needed to turn the cabinet.
- Back panels — Slide the 2 back panels in from the bottom end along the grooves in the side panels until they reach the top panel. The notched corners go to the top panel.
- Back fasteners — Fix the back panels to the bottom panel and the divider: push in 8 plugs (151706), then press a pin (151705) into each.
- Back clips — Press 8 clips (10093081) into the holes: 3 along each side and 2 at the top panel. Then push a wedge (10093082) into each clip.
- Brackets on the leg rails — Lay the 2 leg rails flat, inside face up, next to the 2 leg pieces. Screw an angle bracket (102553) to the middle of each rail with a screw (100347).
- Rails into the right leg piece — Stand the rails on edge, brackets inwards and up. Push the click-in dowels at one end of each rail into the slots in a leg piece, then press the rail down to lock.
- Second leg piece — Push the other leg piece on to the dowels at the free ends of the rails, then press both rails down until they lock.
- Fit the leg frame — Push 4 dowels (101352) into the ends of the side panels, now on top. Turn the leg frame legs-up, lift it over the cabinet and lower it on to the dowels. Check: Two people make this easier.
- Screw the leg frame on — Fix each leg piece to its side panel with 2 long screws (10093458), using the Allen key: 4 screws.
- Brackets to the bottom panel — Screw the bracket on each leg rail to the bottom panel with a screw (100347): 2 screws.
- Adjustable feet — Screw an adjustable foot (131399) into each of the 4 legs and into the centre leg by hand: 5 feet.
- Turn it upright — With a helper, turn the cabinet the right way up: tip it on to its side, then on to its feet. The back still faces you. Check: Two people are needed. Lift, do not drag it on the legs.
- Wall fittings — Press a wall fitting (150688) into the 2 holes on the inside of each side panel, at the top back corner in the notch of the back panel: 2 fittings.
- Adjuster knobs — From behind, screw an adjuster knob (150689) into each wall fitting by hand.
- Turn it round — Turn the cabinet round so the open front faces you.
- Set the knobs — Reach inside and turn each knob so it sticks out a little behind the back, enough to touch the wall when the cabinet stands in place.
- Against the wall — Move the cabinet to where it will stand and push it back until the knobs touch the wall. Check: This cabinet must be fixed to the wall.
- Level it — Check with a spirit level on the top and turn the 5 adjustable feet by hand until the cabinet stands level and steady.
- Mark the wall — Reach in through the open front and mark the wall with a pencil through the hole in each knob.
- Move it away — Move the cabinet away from the wall so you can reach the 2 marks.
- Drill and plug the wall — Drill a hole at each mark: 8 mm and 70 mm deep in solid walls, 8 mm in hollow walls, then tap in the plugs (121714). In solid wood drill 3 mm and use no plug. Ask a specialist if unsure.
- Back against the wall — Push the cabinet back against the wall so the knobs line up with the plugs.
- Screw it to the wall — Through each knob, screw a long screw (147968) with a washer (126916) into the plug, then click a cap (10005905) on to the knob.
- Door tracks — Clip a door track (192163) into the groove under the top rail and another into the groove along the front of the bottom panel.
- Shelf pins — Push 16 shelf pins (131372) into the holes at the shelf heights you want: 4 for each shelf, 8 in each section.
- Shelves — Lay the 4 shelves on the pins, 2 in each section, with the rounded edge to the front and level with the front edges.
- Lay out the doors — Each folding door is 2 leaves. Lay the 4 leaves face down on a soft surface in pairs, the leaves of each door side by side with the fold edges together and the large hinge holes outwards.
- Fold hinges — Join the 2 leaves of each door with 2 hinges (10042027) across the fold, 4 screws (150769) per hinge: 4 hinges and 16 screws.
- Cup hinges — Press a hinge into each of the 2 round holes along the outer edge of each door, arm towards the edge, and tighten its screws: hinge 175136 at the top, 152517 at the bottom. Check: The two 175136 hinges go at the top. Hinge screws and mounting plates come with the hinges.
- Track fittings — Put a track fitting in the notch at the top and bottom corner of the free edge of each door, pin towards the end, and fix each with 2 pins (192158): 10050531 on the left door, 10050552 on the right door, 8 pins.
- Gap strips — Lay a gap strip (10055242) along the fold of each door, lip over the gap. Fix each strip at its middle hole with a plug (10075558) and a pin (10051084) pressed into it. Check: Check the strips are the right way round: the lip covers the gap between the leaves.
- Fix the gap strips — Fix the strips at the remaining holes the same way: 8 plugs (10075558), then a pin (10051084) in each.
- Hang the left door — With a helper, hold the left door open at the cabinet, hinges against the left side panel. Screw its 2 hinge mounting plates to the inside of the side panel, 2 screws each. Check: Have a helper hold the door while you screw. The hinge screws come with the hinges.
- Hang the right door — Hang the right door on the right side panel the same way: 2 hinge mounting plates, 2 screws each.
- Knobs — Hold a knob (10041120) in the hole on the front of each leaf, next to the fold: 4 knobs.
- Screw the knobs on — Swing the doors right open and fix each knob from the inside of the door with a screw (119976): 4 screws.
- Click the doors into the tracks — Fold each door half closed so the corner of its free edge meets the tracks. Push the top pin up into the top track and the bottom pin down into the bottom track until they click, then close the doors. Check: The hinges can be adjusted later (height, side and depth) if the doors do not line up.
- Door stops — Fold the doors open. Under the top rail, push 2 door stops (10050549) into the holes at the fold lines and fix each with 2 pins (192158) from below. Then close the doors.
- Done! — Your IDANÄS cabinet is ready. If a door hangs crooked or the gaps are uneven, adjust it with the screws on its hinges (height, side and depth). Keep it fixed to the wall.
IDANÄS cabinet with bi-folding doors: questions and answers
How long does it take to assemble the IKEA IDANÄS cabinet with bi-folding doors?
About 2–3 h for 2 people, working through the 47 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the IDANÄS cabinet with bi-folding doors?
Phillips screwdriver, hammer, pencil, drill, spirit level, Allen key (included). Already in the box: Allen key.
Can one person assemble the IDANÄS cabinet with bi-folding doors?
It is planned as a 2-person build. One person can do most of it, but get help for steps 6, 9 and 16, where the furniture is lifted or turned.
Does the IDANÄS cabinet with bi-folding doors need to be fixed to the wall?
The manual shows a wall fixing: see step 21 (Wall fittings) and step 27 (Mark the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.
What size is the IDANÄS cabinet with bi-folding doors once assembled?
121×50×135 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.
How many screws and fittings come with the IDANÄS cabinet with bi-folding doors?
160 fittings of 32 kinds, the most numerous being 16 × shelf pin, 16 × screw, 12 × pin. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA IDANÄS cabinet with bi-folding doors assembly instructions PDF?
The official PDF is manual AA-2215723-14, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 204.588.23 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2215723-14. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example door track 192163). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA IDANÄS wardrobe assembly instructions
- IKEA IDANÄS bedside table assembly instructions
- IKEA IDANÄS side table assembly instructions
- IKEA BILLY bookcase assembly instructions
- IKEA KALLAX shelf unit 2x4 assembly instructions
- IKEA BESTÅ frame assembly instructions
- IKEA HYLLIS shelving unit (in/outdoor) assembly instructions
- IKEA LACK wall shelf assembly instructions
All IKEA IDANÄS assembly guides · All bookcases & shelves assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained