IKEA IDANÄS wardrobe assembly instructions
How to assemble the IKEA IDANÄS wardrobe (closet), step by step: 50 animated steps built from the official manual, about 3–4 h for 2 people, with Phillips screwdriver, hammer, pencil, drill, step ladder, Allen keys (included), spanner (included).
A tall white wardrobe on legs with two folding doors, a clothes rod and shelves: the carcass clicks together lying down, the back panels slide in, it stands on a separate leg frame and is fixed to the wall before the bi-fold doors are hung. Size: 121×59×211 cm. About 3–4 h, 2 people. Tools: Phillips screwdriver, Hammer, Pencil, Drill, Step ladder, Allen keys (included), Spanner (included).
Based on the official IKEA manual AA-2215726-10 (PDF). Guide updated .
| Steps | 50 |
|---|---|
| Time | 3–4 h |
| People | 2 |
| Tools | Phillips screwdriver, Hammer, Pencil, Drill, Step ladder, Allen keys (included), Spanner (included) |
| Size | 121×59×211 cm |
| Official manual | AA-2215726-10 |
| IKEA article number | 604.588.35 (white) |
| Pieces in the box | 226 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Side panel | 2 | |
| Bottom panel | 1 | |
| Top panel | 1 | |
| Top rail | 1 | |
| Divider | 1 | |
| Fixed shelf | 1 | |
| Shelf | 3 | |
| Back panel | 2 | |
| Centre leg | 1 | |
| Leg piece | 2 | |
| Leg rail | 2 | |
| Clothes rod | 1 | |
| Door leaf | 4 | |
| Door track | 192163 | 2 |
| Gap strip | 10055263 | 4 |
| Pin | 151705 | 7 |
| Plug | 151706 | 7 |
| Clip | 10093081 | 10 |
| Wedge | 10093082 | 10 |
| Shelf pin | 131372 | 12 |
| Screw | 100347 | 8 |
| Allen key | 100002 | 1 |
| Allen key | 100001 | 1 |
| Spanner | 131398 | 1 |
| Eye bolt | 112805 | 2 |
| Screw | 10093458 | 4 |
| Screw | 100214 | 1 |
| Dowel | 101352 | 9 |
| Angle bracket | 102553 | 4 |
| Sleeve | 10044657 | 2 |
| Adjustable foot | 131399 | 5 |
| Fitting | 10050550 | 2 |
| Butt hinge | 10042027 | 6 |
| Cup hinge | 152517 | 4 |
| Cup hinge | 175136 | 2 |
| Track fitting | 10050531 | 2 |
| Track fitting | 10050552 | 2 |
| Knob | 10041120 | 4 |
| Screw | 119976 | 4 |
| Pin | 192158 | 12 |
| Pin | 10051084 | 20 |
| Plug | 10075558 | 20 |
| Screw | 150769 | 24 |
| Wall bracket | 106989 | 2 |
| Screw | 109049 | 2 |
| Washer | 100823 | 4 |
| Screw | 109048 | 2 |
| Plug | 121714 | 2 |
Steps
- Bottom panel to the right side — Lay the right side panel on its back edge on a rug. Slide the bottom panel against its lower end so the 3 click-in dowels already in the bottom panel go into the keyhole slots, then press the bottom panel down until it locks. Check: Work on a soft surface to protect the panels. Two people are needed for this wardrobe.
- Left side panel — Fit the left side panel on the other end of the bottom panel the same way: dowels into the 3 slots, then press the side panel down so it locks.
- Dowels in the top rail — Push 2 wooden dowels (101352) into the holes in each end of the top rail: 4 dowels.
- Top rail — Lift the top rail in between the side panels at their upper end, along the front edges, and push its dowels into the holes. The groove in the rail faces the bottom of the wardrobe. Check: Check the groove direction before you fit the rail: it will hold the door track.
- Top panel — Slide the top panel on to the upper ends of the side panels so its 6 click-in dowels go into the slots, keep it square to the sides, then press it down to lock.
- Brackets on the top rail — Under the top rail, hold 2 angle brackets (102553) against the back of the rail and screw each to the rail with a screw (100347).
- Brackets to the top panel — Screw the other leg of each bracket to the top panel with a screw (100347): 2 screws.
- Centre leg — Push a dowel (101352) into the outside of the bottom panel and fit the centre leg on it. From inside, fix it with the screw (100214) and the Allen key (100001).
- Divider — Lower the divider into the box against the middle of the bottom panel. Hook its 2 fittings into the slots in the bottom panel and press it down to lock.
- Fixed shelf to the left side — Lower the fixed shelf in between the left side panel and the divider, label side as shown, and push it towards the left side so its 2 fittings go into the slots. Do not press it down yet.
- Shelf on to the divider — Push the fixed shelf on to the 2 fittings at the end of the divider.
- Press the shelf home — Press the fixed shelf down firmly at both ends until all its fittings lock.
- First rod bolt — From inside, put an eye bolt (112805) through the hole near the top end of the right side panel.
- Sleeve on the bolt — From outside, screw a sleeve (10044657) on to the eye bolt with the Allen key (100002).
- Second bolt on the rod — Slide the ring of the second eye bolt (112805) over one end of the clothes rod.
- Clothes rod — Hold the rod at an angle, push its free end through the ring of the first eye bolt, then swing it down so the second bolt goes through the hole in the left side panel. Fix it from outside with a sleeve (10044657) and the Allen key.
- On its side: back panels — With a helper, tip the wardrobe on to its left side. Slide the 2 back panels in from the bottom end along the grooves in the side panels until they reach the top panel. Check: Two people are needed to turn the wardrobe.
- First back fastener, turn it over — Push a plug (151706) through the back into the divider where the back panels meet and press a pin (151705) into it. Then tip the wardrobe on to its front, back facing up.
- Back fasteners — Fix the back panels to the top panel, bottom panel, fixed shelf and divider: push in 6 plugs (151706), then press a pin (151705) into each.
- Back clips — Press 10 clips (10093081) into the holes along both long edges of the back, then push a wedge (10093082) into each clip.
- Brackets on the leg rails — Lay the 2 leg rails flat, inside face up, next to the 2 leg pieces. Screw an angle bracket (102553) to the middle of each rail with a screw (100347).
- Rails into the right leg piece — Stand the rails on edge, brackets inwards and up. Push the click-in dowels at one end of each rail into the slots in the right leg piece, then press the rail down to lock.
- Left leg piece — Push the left leg piece on to the dowels at the other ends of the rails, then press both rails down until they lock.
- Fit the leg frame — Push 4 dowels (101352) into the bottom ends of the side panels. Turn the leg frame legs-out and push it on to the dowels at the bottom end of the wardrobe.
- Screw the leg frame on — Fix each leg piece to its side panel with 2 screws (10093458), using the Allen key (100001): 4 screws.
- Brackets to the bottom panel — Screw the bracket on each leg rail to the bottom panel with a screw (100347): 2 screws. Put cardboard under the legs to protect the floor.
- Adjustable feet — Screw an adjustable foot (131399) into each of the 4 legs and into the centre leg by hand: 5 feet.
- Wall brackets, raise it — Screw the 2 wall brackets (106989) to the back edge of the top panel with a screw (109049) and washer (100823) each, not fully tight. With a helper, raise the wardrobe on to its feet. Check: Two people needed. Check there is room under the ceiling before raising it.
- Against the wall — Move the wardrobe to where it will stand and push it back against the wall. Check: The wardrobe must be fixed to the wall. Use a step ladder, never stand on the wardrobe.
- Level it — Level the wardrobe by turning the 5 adjustable feet with the spanner (131398) until it stands straight and steady.
- Mark the wall — From a step ladder, mark the wall with a pencil through the upright slot of each wall bracket.
- Drill and plug the wall — Move the wardrobe away from the wall. Drill a hole at each mark: 8 mm for solid or hollow walls, then tap in the plugs (121714); in solid wood drill 3 mm and use no plug. Ask a specialist if unsure.
- Screw the brackets to the wall — Push the wardrobe back against the wall. Screw each wall bracket to the wall through its upright slot with a long screw (109048) and a washer (100823).
- Tighten the top screws — Tighten the 2 screws that hold the wall brackets to the top panel.
- Shelf pins — Push 12 shelf pins (131372) into the holes: 4 in the bottom-left section, 8 in the bottom-right section at the two shelf heights you want.
- Shelves — Lay the 3 shelves on the pins, with the rounded edge to the front: one in the left section, two in the right section.
- Door tracks — Clip a door track (192163) into the groove under the top rail and another into the groove along the front of the bottom panel.
- Lay out the doors — Each folding door is 2 leaves. Lay the 4 leaves face down on a soft surface in pairs, the leaves of each door side by side with the fold edges together.
- Fold hinges — Join the 2 leaves of each door with 3 hinges (10042027) across the fold, 4 screws (150769) per hinge: 6 hinges and 24 screws.
- Cup hinges — Press a hinge into each of the 3 round holes along the outer edge of each door, arm towards the edge, and tighten its screws: hinge 175136 at the top, 152517 in the middle and at the bottom. Check: The two 175136 hinges go at the top. Hinge screws and mounting plates come with the hinges.
- Track fittings — Put a track fitting in the notch at the top and bottom corner of the free edge of each door, pin towards the end, and fix each with 2 pins (192158): 10050531 on the left door, 10050552 on the right door, 8 pins.
- Gap strips — Lay 2 gap strips (10055263) along the fold of each door, lip over the gap. Fix each strip at its middle hole with a plug (10075558) and a pin (10051084) pressed into it. Check: Check the strips are the right way round: the lip covers the gap between the leaves.
- Fix the gap strips — Fix the strips at the remaining holes the same way: 16 plugs (10075558), then a pin (10051084) in each.
- Hang the left door — With a helper, hold the left door open at the cabinet, hinges against the left side panel. Screw its 3 hinge mounting plates to the inside of the side panel, 2 screws each. Check: Have a helper hold the door while you screw. The hinge screws come with the hinges.
- Hang the right door — Hang the right door on the right side panel the same way: 3 hinge mounting plates, 2 screws each.
- Knobs — Hold a knob (10041120) in the hole on the front of each leaf, next to the fold: 4 knobs.
- Screw the knobs on — Swing the doors right open and fix each knob from the inside of the door with a screw (119976): 4 screws.
- Fittings under the top rail — Fix the 2 fittings (10050550) under the top rail at the marked holes, each with 2 pins (192158).
- Click the doors into the tracks — Fold each door half closed so the corner of its free edge meets the tracks. Push the top pin up into the top track and the bottom pin down into the bottom track until they click, then close the doors. Check: The hinges can be adjusted later (height, side and depth) if the doors do not line up.
- Done! — Your IDANÄS wardrobe is ready. If a door hangs crooked or the gaps are uneven, adjust it with the screws on its hinges (height, side and depth). Keep it fixed to the wall.
IDANÄS wardrobe: questions and answers
How long does it take to assemble the IKEA IDANÄS wardrobe?
About 3–4 h for 2 people, working through the 50 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the IDANÄS wardrobe?
Phillips screwdriver, hammer, pencil, drill, step ladder, Allen keys (included), spanner (included). Already in the box: Allen keys, Spanner.
Can one person assemble the IDANÄS wardrobe?
It is planned as a 2-person build. One person can do most of it, but get help for steps 4 and 18, where the furniture is lifted or turned.
Does the IDANÄS wardrobe need to be fixed to the wall?
The manual shows a wall fixing: see step 28 (Wall brackets, raise it) and step 31 (Mark the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.
What size is the IDANÄS wardrobe once assembled?
121×59×211 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.
How many screws and fittings come with the IDANÄS wardrobe?
201 fittings of 32 kinds, the most numerous being 24 × screw, 20 × pin, 20 × plug. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA IDANÄS wardrobe assembly instructions PDF?
The official PDF is manual AA-2215726-10, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 604.588.35 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2215726-10. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example door track 192163). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA IDANÄS cabinet with bi-folding doors assembly instructions
- IKEA IDANÄS bedside table assembly instructions
- IKEA IDANÄS side table assembly instructions
- IKEA PAX wardrobe frame assembly instructions
- IKEA BRIMNES wardrobe with 3 doors assembly instructions
- IKEA VISTHUS wardrobe assembly instructions
- IKEA HAUGA wardrobe with sliding doors assembly instructions
- IKEA KLEPPSTAD wardrobe with sliding doors assembly instructions
All IKEA IDANÄS assembly guides · All wardrobes assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained