Step by StepAssembly Find your furniture

IKEA KLEPPSTAD wardrobe with sliding doors assembly instructions

How to assemble the IKEA KLEPPSTAD wardrobe with sliding doors (closet), step by step: 52 animated steps built from the official manual, about 2–3 hours for 2 people, with Phillips screwdriver, flat-blade screwdriver, hammer, pencil, drill with 8 mm bit (wall plugs), step ladder.

IKEA KLEPPSTAD wardrobe with sliding doors, assembled

A white two-door sliding wardrobe with a middle divider, a low fixed shelf and a clothes rail on each side: the carcass is screwed together lying on its front, the back is nailed on, it is stood up and fixed to the wall, then the two doors are hung in their tracks. Size: 117x55x176 cm. About 2–3 hours, 2 people. Tools: Phillips screwdriver, Flat-blade screwdriver, Hammer, Pencil, Drill with 8 mm bit (wall plugs), Step ladder.

Based on the official IKEA manual AA-2208767-7 (PDF). Guide updated .

KLEPPSTAD wardrobe with sliding doors: quick facts
Steps52
Time2–3 hours
People2
ToolsPhillips screwdriver, Flat-blade screwdriver, Hammer, Pencil, Drill with 8 mm bit (wall plugs), Step ladder
Size117x55x176 cm
Official manualAA-2208767-7
IKEA article number904.372.38 (white)
Pieces in the box217

In the box

PartPart numberQuantity
Side panel2
Top panel1
Bottom panel1
Divider1
Fixed shelf2
Short strip2
Plinth strip2
Back panel half2
Sliding door2
Door track100406204
Clothes rail1468542
Dowel10134532
Screw10021420
Allen key1000011
Cam bolt1183314
Cam lock1192534
Angle bracket1026461
Screw1090412
Nail40595060
Nail holder1054941
Glide1535486
Rail holder1573064
Screw1058114
Door stop1153398
Roller1432784
Top guide1432794
Screw10036516
Door stop1921613
Pin1921586
Knob100323112
Screw1095642
Wall bracket1069892
Screw1090492
Washer1008234
Wall screw1090482
Wall plug1217142

Steps

  1. Dowels in the divider and shelves — Lay the divider and the two fixed shelves flat on a soft surface. Push 2 dowels 101345 into each end of the divider and 2 into each end of both shelves: 12 in all. Check: Check the divider's hole pattern against the drawing so the shelf holes are where the manual shows them.
  2. Cam bolts in the divider — Screw 2 cam bolts 118331 by hand or with a Phillips screwdriver into the two holes in the upper face of the divider, low down near the shelf holes.
  3. First shelf onto the divider — Stand one fixed shelf on its end over the divider and lower it straight down, its dowels into the holes and the cam bolts into the holes in its end.
  4. Lock the first shelf — Push 2 cam locks 119253 into the holes in the face of the shelf next to the divider, then turn each one clockwise with a flat-blade screwdriver to lock it onto its cam bolt.
  5. Turn it onto its edge — Turn the divider with its shelf over so the divider stands on its front edge and the shelf lies on the far side.
  6. Second shelf — Screw 2 cam bolts 118331 into the near face of the divider. Stand the second shelf on its front edge and push it against the divider, dowels and cam bolts into its holes.
  7. Lock the second shelf — Push 2 cam locks 119253 into the holes in the second shelf next to the divider and turn each one clockwise to lock it.
  8. Dowels in the top and bottom panels — Lay the top and bottom panels flat, the face with the two grooves up. Push a dowel 101345 into the hole in each end: 4 in all.
  9. Door tracks — Press a door track 10040620 into each of the two grooves near the front edge of both panels: start at one end and press it in bit by bit along the length until it sits flush.
  10. Bottom panel — Hold the divider unit up a little. Stand the bottom panel on its front edge (tracks down) at the shelf end and push it onto the dowels. Fix it with 2 screws 100214 and the Allen key.
  11. Top panel — Stand the top panel on its front edge at the other end, tracks down, and push it onto the dowels in the end of the divider. Fix it with 2 screws 100214.
  12. Near side panel — Stand a side panel on its front edge along the near side and push it onto the dowels in the ends of the top and bottom panels and the shelf.
  13. Screw the near side panel — Fix the side panel with 5 screws 100214 and the Allen key: 3 into the bottom panel and 2 into the shelf.
  14. Dowels in the short strips — Take the two SHORT strips (not the long plinth strips). Push 2 dowels 101345 into each end of both: 8 in all. Check: Use the two shorter strips here; the long ones are for the plinth.
  15. First short strip — Lower one short strip into the top end between the side panel and the divider, against the top panel just behind the tracks, so its dowels go into the holes.
  16. Screw the top of the near side — Fix the top end of the near side panel to the top panel with 3 screws 100214.
  17. Second short strip — From the open side, push the second short strip in along its length so its dowels go into the holes in the divider, against the top panel.
  18. Far side panel — Hold the strip in line and push the second side panel onto the far side, onto the dowels of the top and bottom panels, the shelf and the short strip.
  19. Screw the top of the far side — Fix the top end of the far side panel to the top panel with 3 screws 100214.
  20. Dowels in the plinth strips — Push 2 dowels 101345 into each end of the two long plinth strips: 8 in all.
  21. Plinth strips — Fit both plinth strips under the bottom panel, between the side panels: one along the front edge on the floor, the other about half way back. Their dowels go into the side panels.
  22. Screw the bottom of the far side — Hold the plinth strips in place and fix the bottom end of the far side panel to the bottom panel with 3 screws 100214.
  23. Screw the far side to the shelf — Fix the far side panel to the fixed shelf with 2 screws 100214.
  24. Plinth bracket — In the plinth space, hold the angle bracket 102646 in the corner between the bottom panel and the front plinth strip. Screw it to the bottom panel with a short screw 109041. Check: Use the short screws 109041 here, not the long wall screws.
  25. Screw the bracket to the plinth — Screw the second short screw 109041 down through the slot in the bracket into the front plinth strip.
  26. Back panel halves — Lay the two halves of the back on the frame, smooth side down. They meet in the middle over the divider.
  27. First nail — Line up the back with the outer edges at one top corner. Set a nail 405950 in the nail holder 105494 and hammer it in at that corner. Check: Use the nail holder to keep your fingers clear of the hammer.
  28. Nail the other corners — Push the back square so its edges are flush with the frame, then nail the other three corners: 3 nails 405950.
  29. Nail along the divider — Hammer 12 nails 405950 along the joint between the two halves, into the back edge of the divider.
  30. Nail all round — Hammer in the other 44 nails 405950 all round the edge, into the side panels and the top and bottom panels.
  31. Glides — Press 6 glides 153548 into the holes in the bottom end: 2 under each side panel and 1 in the middle of each plinth strip.
  32. Stand it up at the wall — With a helper, tip the wardrobe up onto its glides, turn it to face you and push it back against the wall where it will stand. Check: Two people needed. Lift it straight up, not at an angle, and check there is room under the ceiling.
  33. Mark the wall — Stand on a step ladder and draw a pencil line on the wall along the top edge of the wardrobe.
  34. Mark the bracket holes — Pull the wardrobe away from the wall. Hold each wall bracket 106989 against the wall, its foot on the pencil line, and mark the wall through its slot. Put the brackets aside.
  35. Drill and plug the wall — Drill an 8 mm hole at each mark, 70 mm deep in a solid wall, and tap in a wall plug 121714 with a hammer. Check: The screws and plugs suit most solid and hollow walls. In solid wood use the screws without plugs (3 mm pilot holes). If unsure, ask a specialist.
  36. Screw the brackets to the wall — Hold each bracket on the wall again and fix it with a washer 100823 and a long screw 109048 into the plug.
  37. Push it back to the wall — Push the wardrobe back against the wall so the top panel slides in under the feet of the two brackets.
  38. Screw the brackets to the top — Put a washer 100823 on each short screw 109049 and screw it down through the slot in each bracket into the top panel.
  39. Rail holders — Open bag 2. Screw the 4 rail holders 157306 near the top, one on each side panel and one on each face of the divider, each with a screw 105811.
  40. Clothes rails — Drop a clothes rail 146854 into each pair of holders.
  41. Door stops — Push 2 door stops 115339 into the pair of holes near each front corner, top and bottom on both side panels: 8 in all.
  42. Rollers on the first door — Lay both doors face down, bottom ends towards the wardrobe. On the first door screw a roller 143278 into each recess at the bottom corners with 2 screws 100365, the − and + marks readable.
  43. Rollers on the second door — Fit the other 2 rollers 143278 to the bottom corners of the second door the same way, each with 2 screws 100365.
  44. Top guides on the first door — At the top corners of the first door screw a top guide 143279 into each recess with 2 screws 100365.
  45. Top guides on the second door — Fit the other 2 top guides 143279 to the second door the same way, each with 2 screws 100365.
  46. Set the right door in its track — Stand up the door with the knob hole on its right edge. Lean the top out and set its rollers into the REAR bottom track at the right. Check: The first door goes in the rear tracks (nearest the back).
  47. Lock the right door — Swing the top of the door in. At each top guide, press the button sideways and slide the guide pin up into the rear top track until it clicks. Check: Hold the door until both guide pins are in the track.
  48. Set the left door in its track — Stand up the second door, knob hole on its left edge. Lean the top out and set its rollers into the FRONT bottom track at the left.
  49. Lock the left door — Swing the door in and slide both guide pins up into the front top track until they click. If a door hangs crooked, turn the − / + adjuster on its roller to raise or lower that side.
  50. Stops on the left door — Slide the left door to the right. Reaching round its left edge, press 3 door stops 192161 onto the back of the door (2 at the top, 1 at the bottom) and push 2 pins 192158 into each.
  51. Knobs — Hold a knob 10032311 on the front of each door at the hole near its outer edge and screw a screw 109564 into it from behind. Slide each door aside to reach behind it.
  52. Done! — Your KLEPPSTAD wardrobe is finished and fixed to the wall. Slide a door by its knob to open either side.

KLEPPSTAD wardrobe with sliding doors: questions and answers

How long does it take to assemble the IKEA KLEPPSTAD wardrobe with sliding doors?

About 2–3 hours for 2 people, working through the 52 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the KLEPPSTAD wardrobe with sliding doors?

Phillips screwdriver, flat-blade screwdriver, hammer, pencil, drill with 8 mm bit (wall plugs), step ladder.

Can one person assemble the KLEPPSTAD wardrobe with sliding doors?

It is planned as a 2-person build. One person can do most of it, but get help for steps 5 and 32, where the furniture is lifted or turned.

Does the KLEPPSTAD wardrobe with sliding doors need to be fixed to the wall?

The manual shows a wall fixing: see step 33 (Mark the wall) and step 34 (Mark the bracket holes). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the KLEPPSTAD wardrobe with sliding doors once assembled?

117x55x176 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the KLEPPSTAD wardrobe with sliding doors?

201 fittings of 26 kinds, the most numerous being 60 × nail, 32 × dowel, 20 × screw. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA KLEPPSTAD wardrobe with sliding doors assembly instructions PDF?

The official PDF is manual AA-2208767-7, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 904.372.38 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2208767-7. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example door track 10040620). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All wardrobes assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained