Step by StepAssembly Find your furniture

IKEA RAKKESTAD wardrobe with 2 doors assembly instructions

How to assemble the IKEA RAKKESTAD wardrobe with 2 doors (closet), step by step: 33 animated steps built from the official manual, about 2–3 h for 2 people, with Phillips screwdriver, hammer, pencil, drill, step ladder, Allen key (included).

IKEA RAKKESTAD wardrobe with 2 doors, assembled

A black-brown two-door wardrobe with a clothes rail and a shelf: the frame is screwed together lying on its front, the folding back panel is nailed on, then it is raised, fixed to the wall and the panelled doors are hung. Size: 79×55×176 cm. About 2–3 h, 2 people. Tools: Phillips screwdriver, Hammer, Pencil, Drill, Step ladder, Allen key (included).

Based on the official IKEA manual AA-2178927-6 (PDF). Guide updated .

RAKKESTAD wardrobe with 2 doors: quick facts
Steps33
Time2–3 h
People2
ToolsPhillips screwdriver, Hammer, Pencil, Drill, Step ladder, Allen key (included)
Size79×55×176 cm
Official manualAA-2178927-6
IKEA article number504.537.58 (black brown)
Pieces in the box146

In the box

PartPart numberQuantity
Side panel2
Top panel1
Bottom panel1
Shelf1
Plinth rail2
Folding back panel1
Door2
Clothes rail1468571
Screw10021912
Dowel10134522
Screw1095672
Screw10524826
Screw1090412
Door stop1238404
Knob1195952
Angle bracket1037171
Nail guide1054941
Allen key1000011
Mounting plate1092216
Hinge1093386
Rail holder1573082
Glide1535486
Nail 405950 (bag)30
Wall bracket1069892
Screw1090492
Washer1008234
Screw1090482
Plug1217142

Steps

  1. Hinge mounting plates — Lay both side panels flat on a soft surface, inside faces up and front edges towards each other. Screw 3 mounting plates (109221) along the front edge of each panel, 2 screws (105248) per plate: 6 plates and 12 screws. Check: Work on a rug or the cardboard so the black-brown foil isn’t scratched. Two people are needed for several steps.
  2. Door stops — Lay the bottom and top panels flat. Tap 2 door stops (123840) into the two holes in the middle of the front edge of each panel with a hammer: 4 door stops.
  3. Dowels into the top and bottom — Push 4 dowels (101345) into the bottom panel and 4 into the top panel, 2 into each short end: 8 dowels.
  4. Turn the bottom over, angle bracket — Turn the bottom panel over. Screw the angle bracket (103717) to it with a short screw (109041), at the hole near the middle of the front edge. Check: Use the short screw 109041 here, not the longer 109567.
  5. Right side up, bottom panel on — Stand the right side panel on its front edge, mounting plates facing in. Push the bottom panel, bracket outwards, onto its dowels at the bottom end and drive 2 screws (100219) through the side panel into it with the Allen key (100001).
  6. Top panel on — Push the top panel onto the dowels at the other end of the right side panel and drive 2 screws (100219) through the side panel into it.
  7. Dowels into the shelf — Lay the shelf flat and push 3 dowels (101345) into each short end: 6 dowels.
  8. Fix the shelf — Stand the shelf on its front edge and push it onto the dowels in the lower holes of the right side panel. Drive 2 screws (100219) through the side panel into it.
  9. Glides on the plinth rails — Stand the 2 plinth rails on their long edge and press a glide (153548) into the 2 holes in the middle of the top edge of each one.
  10. Dowels into the plinth rails — Push 2 dowels (101345) into each end of both plinth rails: 8 dowels.
  11. Front plinth rail — Lay the front plinth rail flat at the bottom end, glide outwards, and slide it under the bottom panel along the front edge until its dowels go into the right side panel.
  12. Middle rail and left side — Slide the second plinth rail in the same way at the holes in the middle of the side panel and hold it there. With a helper, stand the left side panel on its front edge and push it onto the dowels of the top, shelf, bottom and both rails. Check: Two people: one holds the rail and the frame steady while the other fits the side panel.
  13. Bottom screws, not fully — Drive 2 screws (100219) through the left side panel into the bottom panel, but not fully: leave them a little loose for now.
  14. Screw the left side to the top and shelf — Drive 4 screws (100219) through the left side panel: 2 into the top panel and 2 into the shelf.
  15. Tighten the bottom screws — Now tighten the 2 screws at the bottom panel fully with the Allen key, until the heads sit flush with the side panel.
  16. Bracket to the front rail — Fix the angle bracket under the bottom panel to the front plinth rail with the second short screw (109041). Check: Use 109041 here, not 109567.
  17. Lay on the back panel — Lay the folding back panel on the frame and unfold it flat, so it sits in the rebates. Push it against the edges and check the frame is square: the gap must be the same on both sides.
  18. Nail the first half — Hold the nail guide (105494) on the edge, put a nail (405950) through it and hammer it in. Nail along the top end and down the left side of the back panel: 15 nails.
  19. Nail the second half — In the same way, nail the other side and the bottom end of the back panel, using the nail guide: 15 nails.
  20. Glides under the side panels — Press 2 glides (153548) into the holes in the bottom end of each side panel: 4 glides.
  21. Raise the wardrobe — With a helper, lift the top end and walk the wardrobe up onto its glides, keeping the bottom end on the floor. Check: Two people needed. Check there is room under the ceiling to raise it.
  22. Against the wall, mark the top — Push the wardrobe against the wall where it will stand. Draw a pencil line on the wall along the top of the wardrobe. Check: The wardrobe must be fixed to the wall to stop it tipping over. Use a step ladder, not the wardrobe, to reach the top.
  23. Mark the wall brackets — Pull the wardrobe away from the wall. Hold each wall bracket (106989) with its flat leg on the pencil line and mark the wall through the slot in the upright leg.
  24. Drill and plug the wall — Drill a hole at each mark: 8 mm for the plugs in solid or hollow walls, then tap in the plugs (121714). In solid wood, drill 3 mm and use no plug. If unsure which fixings suit your wall, ask a specialist.
  25. Screw the brackets to the wall — Hold each bracket with its slot over the plug and screw it to the wall with a screw (109048) and a washer (100823).
  26. Push it back — Push the wardrobe back against the wall, so the flat legs of the brackets rest on the top panel.
  27. Screw the brackets to the top — Standing on a step ladder, screw each bracket to the top panel with a short screw (109049) and a washer (100823), through the slot in the flat leg. Check: Use 109049 here: the longer 109048 is only for the wall. Don’t stand on the wardrobe.
  28. Clothes rail holders — Screw a rail holder (157308) to each side panel, near the top, with a screw (105248) each.
  29. Clothes rail — Drop the clothes rail (146857) into the two holders.
  30. Hinges on the doors — Lay the 2 doors flat, inside face up. Press a hinge (109338) into each of the 6 round holes, arm towards the door edge, and fix each with 2 screws (105248): 12 screws.
  31. Hang the doors — Hook the hinge arms of the left door onto the mounting plates on the left side panel, and the right door onto the right side panel. Open the doors and tighten the screw on each of the 6 hinge arms. Check: Have a helper hold each door while you clip its hinges on. The hinge screws also adjust the doors if the gaps are uneven.
  32. Knobs — Hold a knob (119595) on the front of each door at the hole near the meeting edge and screw it on from the inside with a screw (109567). Then close the doors.
  33. Done! — Your RAKKESTAD wardrobe is ready. If a door hangs crooked or the gaps are uneven, adjust it with the screws on its hinges (height, side and depth). Keep it fixed to the wall.

RAKKESTAD wardrobe with 2 doors: questions and answers

How long does it take to assemble the IKEA RAKKESTAD wardrobe with 2 doors?

About 2–3 h for 2 people, working through the 33 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the RAKKESTAD wardrobe with 2 doors?

Phillips screwdriver, hammer, pencil, drill, step ladder, Allen key (included). Already in the box: Allen key.

Can one person assemble the RAKKESTAD wardrobe with 2 doors?

It is planned as a 2-person build. One person can do most of it, but get help for steps 4 and 21, where the furniture is lifted or turned.

Does the RAKKESTAD wardrobe with 2 doors need to be fixed to the wall?

The manual shows a wall fixing: see step 23 (Mark the wall brackets) and step 33 (Done). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the RAKKESTAD wardrobe with 2 doors once assembled?

79×55×176 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the RAKKESTAD wardrobe with 2 doors?

105 fittings of 19 kinds, the most numerous being 26 × screw, 22 × dowel, 12 × screw. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA RAKKESTAD wardrobe with 2 doors assembly instructions PDF?

The official PDF is manual AA-2178927-6, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 504.537.58 (black brown); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2178927-6. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example clothes rail 146857). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA RAKKESTAD assembly guides · All wardrobes assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained