Step by StepAssembly Find your furniture

IKEA PAX wardrobe frame assembly instructions

How to assemble the IKEA PAX wardrobe frame (closet), step by step: 23 animated steps built from the official manual, about 30–45 min for 2 people, with flat-head screwdriver, spirit level, step ladder, Allen key (included).

IKEA PAX wardrobe frame, assembled

The new fold-out PAX frame: it arrives pre-hinged and folded, stands up, unfolds, clicks onto adjustable feet and is anchored to the wall. Size: 100×58×201 cm (39 3/8×22 7/8×79 1/4"). About 30–45 min, 2 people. Tools: Flat-head screwdriver, Spirit level, Step ladder, Allen key (included).

Based on the official IKEA manual AA-2174072-9 (PDF). Guide updated .

PAX wardrobe frame: quick facts
Steps23
Time30–45 min
People2
ToolsFlat-head screwdriver, Spirit level, Step ladder, Allen key (included)
Size100×58×201 cm (39 3/8×22 7/8×79 1/4")
Official manualAA-2174072-9
IKEA article number704.582.03 (white)
Pieces in the box32

In the box

PartPart numberQuantity
Folded frame: 2 side panels + 2-part back panel1
Top panel1
Bottom panel1
Plinth2
Adjustable foot101086984
Plinth bracket100425262
Plinth clip101205052
Rear plinth clip100462782
Corner fitting L100426121
Corner fitting R100426251
Front corner fitting100425432
Wall spacer100462752
Washer1008232
Cover cap100426102
Plug1013492
Allen key100943151
Screw 100402 (joining frames)2
Connector sleeve 100644 (joining frames)2

Steps

  1. Stand the folded frame up — The frame comes pre-hinged and folded, held by two straps. With two people, lift the pack from the floor and stand it upright against the wall. Leave the straps on. Check: Two people needed. Do not cut the straps with scissors or a knife and do not lift the pack by the straps.
  2. Pull off the two straps — Pull the tear tab on each strap upwards, in the direction of the arrows, to open it. Keep holding the pack so it cannot fall. Check: Do not cut the straps open: you could damage the panels.
  3. Unfold the back panel — One person holds the left side panel slightly open. The other swings the right half of the back panel, with the right side panel still folded against it, out to the right until the back is flat. Check: Two people needed: keep the frame upright while you unfold it.
  4. Swing the side panels open — Swing the left side panel out to the left and the right side panel out to the right, so the frame stands open like a U.
  5. Hook on the 4 adjustable feet — First turn the height screw of each foot all the way in. Then put the 4 feet into the keyhole slots at the bottom of the side panels, studs first, and push them down until they lock.
  6. Clip the brackets onto the rear feet — Press the rear feet firmly into the panels. Clip a plinth bracket onto the inner face of each rear foot and push it down.
  7. Fit the rear plinth — Lower the rear plinth into the two brackets, in front of the rear feet, and push it down at both ends.
  8. Square the frame, fit the front plinth — Set both side panels at right angles to the back. Push the front plinth onto the studs of the two front feet, then press it down to lock.
  9. Clip the front plinth to the feet — From the inside, slide a clip over the top edge of the front plinth and the foot at each end until it sits tight.
  10. Clip the rear plinth — Press the 2 clips down over the top edge of the rear plinth so they hook behind the studs.
  11. Corner fitting R at the top right — Using a step ladder, press the corner fitting marked R onto the two studs in the top back corner of the right side panel, then push in its locking pin. Check: Use a stable step ladder; do not climb on the frame.
  12. Corner fitting L at the top left — Fit the corner fitting marked L in the top back corner of the left side panel in the same way.
  13. Lift in the top panel — From the ladder, lift the top panel in tilted, left end first against the L fitting. Swing the right end up so the 4 studs drop into the keyhole holes, then slide the panel to the left until it stops. Check: Lift the top panel in level with the frame; do not turn it through the frame diagonally.
  14. Lock the top panel — Check that the top panel is flush with the tops of the side panels. Push the latch on both corner fittings up to lock the top panel.
  15. Front corner fittings — Hook each front corner fitting into the hole under the top panel at the front corners, swing it up against the side panel and press it home.
  16. Level the frame — Push the frame into place against the wall. Check it with a spirit level and adjust the height of each foot by turning the Allen key in the hole at the top of the foot.
  17. Plugs into the front feet — Push a plug into the hole at the top of each front foot.
  18. Screw in the wall spacers — Screw a wall spacer into the round hole of each corner fitting until it touches the wall. It can bridge a gap of up to 22 mm (7/8"), e.g. over a skirting board.
  19. Fix the frame to the wall — Check that the frame is level. Fix it to the wall through both wall spacers with a washer and a screw that suits your wall. Check: Must be fixed to the wall to prevent tip-over. Wall screws and plugs are not included; use ones suitable for your wall.
  20. Click on the cover caps — Hook each cover cap over its corner fitting and swing it in until it clicks.
  21. Lay in the bottom panel — Lower the bottom panel onto the plinths so the holes underneath fit over the 2 plugs in the front feet.
  22. Joining two frames (optional) — Only when you place two PAX frames side by side (manual page 23): clamp the frames together, drill through hole 5 at the top and bottom with a 5 mm bit, push a connector sleeve in from one side and screw a screw into it from the other. With a single frame, keep these 4 parts.
  23. Done! — Your PAX wardrobe frame is assembled and anchored to the wall, ready for doors and interior fittings.

PAX wardrobe frame: questions and answers

How long does it take to assemble the IKEA PAX wardrobe frame?

About 30–45 min for 2 people, working through the 23 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the PAX wardrobe frame?

Flat-head screwdriver, spirit level, step ladder, Allen key (included). Already in the box: Allen key.

Can one person assemble the PAX wardrobe frame?

It is planned as a 2-person build. One person can do most of it, but get help for steps 1 and 13, where the furniture is lifted or turned.

Does the PAX wardrobe frame need to be fixed to the wall?

The manual shows a wall fixing: see step 18 (Screw in the wall spacers) and step 19 (Fix the frame to the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the PAX wardrobe frame once assembled?

100×58×201 cm (39 3/8×22 7/8×79 1/4"), as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the PAX wardrobe frame?

22 fittings of 11 kinds, the most numerous being 4 × adjustable foot, 2 × plinth bracket, 2 × plinth clip. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA PAX wardrobe frame assembly instructions PDF?

The official PDF is manual AA-2174072-9, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 704.582.03 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2174072-9. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example adjustable foot 10108698). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All wardrobes assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained