Step by StepAssembly Find your furniture

IKEA HAUGA wardrobe with sliding doors assembly instructions

How to assemble the IKEA HAUGA wardrobe with sliding doors (closet), step by step: 40 animated steps built from the official manual, about 2–3 hours for 2 people, with Phillips screwdriver, flat-blade screwdriver, hammer, pencil, drill with 8 mm bit (wall plugs), step ladder.

IKEA HAUGA wardrobe with sliding doors, assembled

A white two-door sliding wardrobe with a middle divider, a fixed shelf and a clothes rail on each side: the carcass clicks together lying on its front, is stood up and fixed to the wall, then the two doors are hung in their top and bottom tracks. Size: 118x55x199 cm. About 2–3 hours, 2 people. Tools: Phillips screwdriver, Flat-blade screwdriver, Hammer, Pencil, Drill with 8 mm bit (wall plugs), Step ladder.

Based on the official IKEA manual AA-2205173-8 (PDF). Guide updated .

HAUGA wardrobe with sliding doors: quick facts
Steps40
Time2–3 hours
People2
ToolsPhillips screwdriver, Flat-blade screwdriver, Hammer, Pencil, Drill with 8 mm bit (wall plugs), Step ladder
Size118x55x199 cm
Official manualAA-2205173-8
IKEA article number604.569.16 (white)
Pieces in the box176

In the box

PartPart numberQuantity
Side panel2
Top panel1
Bottom panel1
Divider1
Fixed shelf2
Back panel half2
Plinth rail2
Back strip1
Sliding door2
Clothes rail100424022
Top track (U)100469922
Bottom track (W)100470042
Dowel10134514
Screw1461134
Back clip1009308114
Clip cap1009308214
Plug15170618
Pin15170518
Glide1535482
T glide100400394
Connector rod100508272
Cam lock1134344
Rail holder100423654
Pin19215822
Door stop1153398
Bolt1199762
Knob100519402
Door stop1921613
Bottom roller1505214
Allen key1000491
Top guide1921574
Wall bracket1069892
Screw1090492
Washer1008234
Wall screw1090482
Wall plug1217142

Steps

  1. Dowels in the fixed shelves — Lay the two fixed shelves flat on a soft surface. Push 2 dowels 101345 into the holes in the edge of each shelf that will face the divider.
  2. First shelf onto the divider — Stand the divider on its front edge. Stand the first fixed shelf up on its front edge on the far side and push it against the divider, its dowels into the holes low down near the bottom end.
  3. Connector rods through the divider — Hold the shelf in place. From the near side, push 2 connector rods 10050827 through the holes in the divider into the shelf, as far as the clip on the rod.
  4. Lock the rods in the shelf — Push 2 cam locks 113434 into the holes in the underside of the shelf, next to the rods, and turn each clockwise with a flat-blade screwdriver to lock the rod.
  5. Second shelf and its cam locks — Stand the second fixed shelf on its front edge on the near side and push it onto the rods and against the divider. Lock it with 2 cam locks 113434 in its underside, turned clockwise.
  6. Wall brackets on the top panel — Open the wall-fixing bag. Lay the top panel flat, top face up. Fix a wall bracket 106989 near each end of its back edge with a washer 100823 and a screw 109049 through the slot. Leave the screws a little loose for now.
  7. Top panel onto the divider — Hold the divider up a little and stand the top panel on its front edge at the top end, brackets up. Push it onto the 3 knobs in the end of the divider, then press it down until it clicks.
  8. Bottom panel — Stand the bottom panel on its front edge at the other end, next to the fixed shelves. Push it onto the 3 knobs in the divider and press it down until it clicks.
  9. Far side panel — Stand a side panel on its front edge along the far side, the rounded corner at the top end. Push its keyholes over the 9 knobs (top, bottom and shelf), then press it down until it clicks. Check: The rounded corner goes at the top front: check before you click it on.
  10. Near side panel — Fit the other side panel on the near side the same way: keyholes over the 9 knobs, rounded corner at the top end, then press it down until it clicks.
  11. First back half — Lay the first half of the back on the near half of the frame, smooth side down. Slide it towards the near side panel so its edge goes into the groove.
  12. Second back half — With a helper, lay the second half on the far half of the frame and slide it towards the far side panel into its groove. The two halves meet over the divider.
  13. Plugs in the back — Push a plug 151706 into each of the 18 holes in the back: along the top and bottom panels, along the fixed shelves and down the divider.
  14. Clips along the sides — Along both side panels, slide a clip 10093081 over the edge of the back into each of the 7 holes, then push a cap 10093082 onto each clip. 14 of each.
  15. Pins into the plugs — Push a pin 151705 into each of the 18 plugs until its head sits flat on the back.
  16. Plinth rails — Push 6 dowels 101345 into the holes in the underside of the bottom panel, 3 along the front and 3 along the back. Push the two plinth rails onto them.
  17. T glides at the corners — Press a T glide 10040039 into the holes at each of the 4 corners of the bottom end: under the side panels, next to the plinth rails.
  18. Glides under the plinth — Press a glide 153548 into the 2 holes in the middle of each plinth rail.
  19. Stand it up at the wall — With a helper, tip the wardrobe up onto its bottom end, turn it round to face you and push it back against the wall where it will stand. Check: Two people needed. Lift it straight up, don't tilt it at an angle, and check there is room under the ceiling.
  20. Mark the bracket holes — Stand on a step ladder. Mark the wall through the slot in each of the 2 wall brackets with a pencil.
  21. Move it away from the wall — Pull the wardrobe forward, away from the wall, so you can drill at the two pencil marks.
  22. Drill and plug the wall — Drill an 8 mm hole, 70 mm deep, at each mark and tap in a wall plug 121714 with a hammer. Then push the wardrobe back against the wall. Check: The plugs and screws suit most solid and hollow walls. In solid wood use the screws without plugs (3 mm pilot holes). If unsure, ask a specialist.
  23. Screw it to the wall — Put a washer 100823 on each screw 109048 and screw them through the slots in the wall brackets into the plugs.
  24. Tighten the bracket screws — Now tighten the 2 screws 109049 that hold the wall brackets on the top panel.
  25. Dowels for the back strip — Push 4 dowels 101345 into the holes near the top back corner of the side panels, 2 on each side, by hand. Check: Don't hammer the dowels in.
  26. Back strip — Lower the back strip between the side panels at the back, in front of the wall brackets, so it slides down onto the 4 dowels.
  27. Bottom tracks — Press the 2 W-shaped bottom tracks 10047004 into the grooves at the front of the bottom panel, the W facing up. Start at one end and press them in bit by bit along the length.
  28. Top tracks — Press the 2 U-shaped top tracks 10046992 up into the grooves under the front of the top panel, open side down, bit by bit from one end.
  29. Rail holders — Screw the 4 rail holders 10042365 near the top: one on each side panel and one on each face of the divider, each with a screw 146113.
  30. Clothes rails — Drop a clothes rail 10042402 into each pair of holders.
  31. Door stops — Open bag 2. Push 2 door stops 115339 into the pair of holes near each front corner, top and bottom on both side panels: 8 in all.
  32. Top guides on the doors — Lay both doors face up, top ends together. At each top corner press a top guide 192157 into the recess, then fix it with 2 pins 192158 pushed in by hand.
  33. Bottom rollers — At each bottom corner press a bottom roller 150521 into the recess, adjuster wheel facing out, and fix it with 2 pins 192158.
  34. Hang the rear door — Stand the door with the knob hole on its left edge up. Put its top guides up into the rear top track at the right, swing the bottom in and set the rollers on the rear bottom track. Push the lock on each guide up until it clicks. Check: Rear door first, in the rear tracks (nearest the back).
  35. Hang the front door — Slide the rear door to the left. Hang the second door, knob hole on its right edge, in the front tracks at the right in the same way, and push its 2 guide locks up until they click.
  36. Level the doors — If the gap between a door and a side panel isn't even, turn the adjuster wheel on its bottom roller with the Allen key 100049 to raise or lower that side of the door.
  37. Stops on the front door — Slide the front door to the left. Reaching round its right edge, press 3 door stops 192161 onto the back of the door near that edge: 2 at the top and 1 at the bottom.
  38. Pin the stops — Push 2 pins 192158 through each door stop into the door, 6 in all, then slide the front door back to the right.
  39. Knobs — Slide the doors apart in the middle. Hold a knob 10051940 on the front of each door at the hole on its outer edge and screw a bolt 119976 into it from behind the door.
  40. Done! — Your HAUGA wardrobe is finished and fixed to the wall. Slide a door by its knob to open either side.

HAUGA wardrobe with sliding doors: questions and answers

How long does it take to assemble the IKEA HAUGA wardrobe with sliding doors?

About 2–3 hours for 2 people, working through the 40 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the HAUGA wardrobe with sliding doors?

Phillips screwdriver, flat-blade screwdriver, hammer, pencil, drill with 8 mm bit (wall plugs), step ladder.

Can one person assemble the HAUGA wardrobe with sliding doors?

It is planned as a 2-person build. One person can do most of it, but get help for steps 2, 19 and 34, where the furniture is lifted or turned.

Does the HAUGA wardrobe with sliding doors need to be fixed to the wall?

The manual shows a wall fixing: see step 6 (Wall brackets on the top panel) and step 20 (Mark the bracket holes). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the HAUGA wardrobe with sliding doors once assembled?

118x55x199 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the HAUGA wardrobe with sliding doors?

161 fittings of 26 kinds, the most numerous being 22 × pin, 18 × plug, 18 × pin. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA HAUGA wardrobe with sliding doors assembly instructions PDF?

The official PDF is manual AA-2205173-8, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 604.569.16 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2205173-8. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example clothes rail 10042402). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA HAUGA assembly guides · All wardrobes assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained