IKEA HAUGA bedside table assembly instructions
How to assemble the IKEA HAUGA bedside table (nightstand), step by step: 26 animated steps built from the official manual, about 1–1.5 hours for 1 person, with Phillips screwdriver, flat screwdriver.
A white bedside table with one drawer under the top and an open space below: the carcass clicks together lying on its front, stands up, then the drawer is built on its front and slid in on its runners. Size: 40x36x63 cm. About 1–1.5 hours, 1 person. Tools: Phillips screwdriver, Flat screwdriver.
Based on the official IKEA manual AA-2523359-1 (PDF). Guide updated .
| Steps | 26 |
|---|---|
| Time | 1–1.5 hours |
| People | 1 |
| Tools | Phillips screwdriver, Flat screwdriver |
| Size | 40x36x63 cm |
| Official manual | AA-2523359-1 |
| IKEA article number | 004.889.63 (white) |
| Pieces in the box | 65 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Side panel | 2 | |
| Top panel | 1 | |
| Bottom panel | 1 | |
| Back panel | 1 | |
| Plinth rail | 1 | |
| Top back rail | 1 | |
| Drawer front | 1 | |
| Drawer side | 2 | |
| Drawer back | 1 | |
| Drawer bottom | 1 | |
| Runner set 10047099 (CR, CL, DR, DL) | 1 | |
| Screw | 146114 | 8 |
| Plug | 151706 | 4 |
| Pin | 151705 | 4 |
| Back clip | 10093081 | 4 |
| Clip cap | 10093082 | 4 |
| Dowel | 101345 | 6 |
| Glide | 153548 | 2 |
| T glide | 10040039 | 2 |
| Cam screw | 118331 | 4 |
| Cam lock | 119030 | 8 |
| Cam bolt | 145718 | 4 |
| Knob | 10052019 | 1 |
| Bolt | 119976 | 1 |
Steps
- Runners on the side panels — Lay both side panels flat on a rug, inner side up. Screw runner CR onto the right panel and runner CL onto the left one with 2 screws 146114 each, wheel at the front edge. Check: Check the CR / CL labels: each runner only fits its own side.
- Bottom panel onto the far side — Stand the left side panel on its front edge, rounded corner at the top end. Push the bottom panel's knobs into the keyholes at the bottom end, then press the panel down towards the floor until it clicks.
- Top panel — Fit the top panel near the top end in the same way, just above the runner: knobs into the keyholes, then press it down until it clicks. Check: The top panel sits about 7 cm below the top of the side panel, where the rounded corner ends.
- Second side panel — Stand the right side panel on its front edge, rounded corner at the top end. Push its keyholes over the knobs of the top and bottom panels and press it down until it clicks.
- Slide in the back panel — From the bottom end, slide the back panel into the grooves of both side panels, over the bottom panel, until it stops against the top panel.
- Fix the back to the bottom panel — Push a plug 151706 through each of the 2 holes at the bottom end of the back, into the edge of the bottom panel. Push a pin 151705 into each plug until its head sits flat.
- Clips along the sides — Slide a clip 10093081 over the edge of the back into each of the 4 holes in the side panels, 2 on each side. Push a cap 10093082 into each clip.
- Dowels in the plinth rail — Push 2 dowels 101345 by hand into the holes in one long edge of the plinth rail. Check: Don't hammer the dowels in.
- Plinth rail — Push the plinth rail, dowels first, into the holes in the bottom panel at the front of the bottom end.
- Glides — Press a glide 153548 into the bottom end of each side panel at the back, and a T glide 10040039 at each front corner, under the side panel and the end of the plinth rail.
- Dowels in the top back rail — Take the narrow rail with the 2 round pockets. Push 2 dowels 101345 by hand into the holes in its long edge. Check: Don't hammer the dowels in.
- Top back rail in — At the top end, hold the rail between the side panels at the back, pockets facing up, and push it in so its dowels go into the top panel.
- Lock the top back rail — In each round pocket of the rail, push a plug 151706 sideways into the hole towards the side panel, then push a pin 151705 into the plug.
- Stand it up — Tip the table up onto its glides and turn it round so the front faces you.
- Cam screws in the drawer front — Lay the drawer front face down on the rug. Screw 4 cam screws 118331 into the holes near its two short ends, 2 at each end.
- Dowels in the drawer sides — Lay the two drawer sides flat, grooves up. Push a dowel 101345 by hand into the hole in the front end of each side.
- Sides onto the front — Stand each side up over the drawer front, groove on the inside, and push it straight down so its dowel and the 2 cam screws go into its end. Check: The groove for the bottom must be at the same height on both sides.
- Cam locks in the sides — Put a cam lock 119030 into each of the 4 holes in the outer faces of the sides, next to the front. Turn each one clockwise with a flat screwdriver to lock it.
- Drawer bottom — Slide the drawer bottom down into the grooves of both sides until it reaches the front.
- Drawer back — Lay the drawer back between the top ends of the sides, its 4 big holes facing up and its groove over the edge of the bottom.
- Cam bolts through the sides — Push a cam bolt 145718 by hand into each of the 4 holes in the outer faces of the sides at the back end, so it goes into the end of the drawer back.
- Cam locks in the back — Put a cam lock 119030 into each of the 4 big holes in the drawer back and turn it clockwise with a flat screwdriver until it grips the cam bolt.
- Runners on the drawer — Stand the drawer upright. Fit runner DR along the bottom edge of the right side and DL on the left, wheel at the back, and screw each on with 2 screws 146114.
- Knob — Hold the knob 10052019 on the front of the drawer at the middle hole and screw the bolt 119976 into it from inside the drawer.
- Drawer in — Lift the drawer in front of its opening under the top panel, set its runners on the runners in the table and push it all the way in.
- Done! — Your HAUGA bedside table is ready. Don't sit on it, and keep the load on top under 25 kg.
HAUGA bedside table: questions and answers
How long does it take to assemble the IKEA HAUGA bedside table?
About 1–1.5 hours for 1 person, working through the 26 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the HAUGA bedside table?
Phillips screwdriver, flat screwdriver.
Can one person assemble the HAUGA bedside table?
Yes, it is a one-person build.
What size is the HAUGA bedside table once assembled?
40x36x63 cm, as given for this model. Leave extra floor space around it while you build.
How many screws and fittings come with the HAUGA bedside table?
52 fittings of 13 kinds, the most numerous being 8 × screw, 8 × cam lock, 6 × dowel. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA HAUGA bedside table assembly instructions PDF?
The official PDF is manual AA-2523359-1, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 004.889.63 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2523359-1. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example runner set 10047099). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA HAUGA wardrobe with sliding doors assembly instructions
- IKEA HAUGA cabinet with 2 doors assembly instructions
- IKEA HEMNES 3-drawer dresser assembly instructions
- IKEA MALM chest of 3 drawers assembly instructions
- IKEA ALEX drawer unit assembly instructions
- IKEA LENNART drawer unit assembly instructions
- IKEA MALM dressing table assembly instructions
- IKEA BRIMNES bedside table assembly instructions
All IKEA HAUGA assembly guides · All dressers & drawers assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained