IKEA HAUGA cabinet with 2 doors assembly instructions
How to assemble the IKEA HAUGA cabinet with 2 doors, step by step: 41 animated steps built from the official manual, about 2–3 hours for 2 people, with Phillips screwdriver, pencil, drill with Ø 8 mm bit (Ø 3 mm for wood), hammer.
A white cabinet with two panelled doors and an open top unit: the lower cabinet clicks together lying on its front, stands up, takes the top unit on one tall back panel, is fixed to the wall, then gets its shelves and doors. Size: 70x46x116 cm. About 2–3 hours, 2 people. Tools: Phillips screwdriver, Pencil, Drill with Ø 8 mm bit (Ø 3 mm for wood), Hammer.
Based on the official IKEA manual AA-2204746-8 (PDF). Guide updated .
| Steps | 41 |
|---|---|
| Time | 2–3 hours |
| People | 2 |
| Tools | Phillips screwdriver, Pencil, Drill with Ø 8 mm bit (Ø 3 mm for wood), Hammer |
| Size | 70x46x116 cm |
| Official manual | AA-2204746-8 |
| IKEA article number | 004.150.52 (white) |
| Pieces in the box | 119 |
In the box
| Part | Part number | Quantity |
|---|---|---|
| Side panel (cabinet) | 2 | |
| Top panel | 1 | |
| Bottom panel | 1 | |
| Back panel | 1 | |
| Plinth rail | 1 | |
| Side panel (top unit) | 2 | |
| Top-unit shelf | 1 | |
| Back rail | 1 | |
| Shelf | 2 | |
| Door | 2 | |
| Pin | 151707 | 10 |
| Plug | 151708 | 10 |
| Back clip | 10093081 | 8 |
| Clip cap | 10093082 | 8 |
| Dowel | 101345 | 5 |
| Glide | 158568 | 2 |
| T glide | 10051022 | 2 |
| Long dowel | 120173 | 4 |
| Hinge plate | 10039878 | 4 |
| Hinge | 10039873 | 4 |
| Shelf support | 10051650 | 8 |
| Cap | 190586 | 2 |
| Cap | 10047146 | 2 |
| Knob | 10052019 | 2 |
| Bolt | 119976 | 2 |
| Connecting plate | 10049270 | 2 |
| Plug | 144575 | 8 |
| Pin | 144574 | 8 |
| Door stop | 10050715 | 2 |
| Pin | 10051084 | 2 |
| Wall bracket | 150688 | 2 |
| Knob | 150689 | 2 |
| Washer | 126916 | 2 |
| Wall screw 147968 or | 158469 | 2 |
| Wall plug | 121714 | 2 |
Steps
- Side panels on a soft surface — Lay the two side panels of the cabinet flat on a rug or the empty box, inner side (with the keyholes) up, so they don't get scratched.
- Top panel onto the far side — Stand one side panel on its front edge, the rounded corner at the top end. Push the top panel's 3 knobs into the keyholes near the top end, then press the panel down towards the floor until it clicks. Check: The top panel sits about 7 cm below the top of the side panels, where the rounded corner ends.
- Bottom panel — Fit the bottom panel at the other end of the side panel in the same way: knobs into the keyholes, then press it down until it clicks.
- Second side panel — Stand the other side panel on its front edge, rounded corner at the top end. Push its keyholes over the knobs of the top and bottom panels and press it down until it clicks.
- Slide in the back panel — From the bottom end, slide the back panel into the grooves of both side panels, over the bottom and top panels, until it sticks out past the top end. That part will carry the top unit.
- Plugs in the back — Push a plug 151708 through each of the 8 holes in the back into the edges of the top and bottom panels, 4 along each. Check: Use the plugs 151708 here, not 144575.
- Clips along the sides — Slide a clip 10093081 over the edge of the back into each of the 6 holes in the side panels, 3 on each side. Push a cap 10093082 onto each clip.
- Pins into the plugs — Push a pin 151707 into each of the 8 plugs until its head sits flat on the back. Check: Use the pins 151707 here, not 144574.
- Plinth rail — Push 2 dowels 101345 by hand into the holes in the plinth rail, then push the rail onto the bottom panel at the front of the bottom end. Check: Don't hammer the dowels in.
- Glides — Press a glide 158568 into the bottom end of each side panel at the back, and a T glide 10051022 at each front corner, under the side panel and the plinth rail.
- Stand the cabinet up — With a helper, tip the cabinet up onto its glides and turn it to face you. Lift it by the side panels, not by the back panel. Check: Two people needed. Never lift or carry it by the part of the back that sticks out.
- Caps in the side panels — Press a cap 10047146 into the hole in the inner face of each side panel, above the top panel at the back.
- Long dowels in the top unit — Lay the two side panels of the top unit flat, inner side up. Push 2 long dowels 120173 into the holes in the bottom end of each panel.
- Shelf onto the first side — Stand one top-unit side panel on its front edge, dowels at the bottom end. Push the shelf's knobs into its keyholes near the top, then press the shelf down until it clicks.
- Second top-unit side — Stand the other side panel on its front edge and push its keyholes over the shelf's knobs, then press it down until it clicks.
- Back rail — Push 3 dowels 101345 by hand into the edge of the back rail. Turn the rail over and lower it between the side panels at the back, so the dowels go into the back edge of the shelf. Check: Don't hammer the dowels in.
- Plugs and pins in the rail — Push a plug 151708 into each of the 2 holes in the back of the rail, then push a pin 151707 into each plug. Check: Plugs 151708 and pins 151707 here, not 144575 and 144574.
- Top unit onto the cabinet — With a helper, lift the top unit upright, hold it over the cabinet and lower it straight down: the back panel goes into the groove under the back rail and the long dowels into the tops of the side panels. Check: Two people needed.
- Connecting plates — At the back, hold a connecting plate 10049270 over the joint on each side. Push a plug 144575 through each of its 4 holes, then a pin 144574 into each plug. Check: Use plugs 144575 and pins 144574 here, not 151708 and 151707.
- Clips in the top unit — Slide a clip 10093081 over the edge of the back into the hole in each top-unit side panel and push a cap 10093082 onto it.
- Wall brackets — Open the wall-fixing bag. Push the 2 pins of a wall bracket 150688 into the holes in each side panel behind the back, just under the top panel, its round threaded part over the hole in the back.
- Knobs (only with a skirting board) — If there is a skirting board where the cabinet will stand, screw a knob 150689 onto each wall bracket, clockwise. Without a skirting board, leave the knobs out and skip to marking the wall.
- Set the knobs — Turn each knob out (anticlockwise) until it sticks out past the back edge by about the thickness of your skirting board.
- Against the wall — Move the cabinet to its place and push it back until its lower edge rests against the skirting board and both knobs touch the wall, so it stands straight. Check: If a knob doesn't touch the wall, turn it out a little more.
- Mark the wall — Reach in under the top panel and mark the wall with a pencil through the hole in the back panel and wall bracket, on both sides.
- Move the cabinet aside — Pull the cabinet forward and move it to one side, clear of the two marks.
- Drill the holes — Drill a hole at each mark: Ø 8 mm and 70 mm deep in a solid wall, about 30 mm in a hollow wall, or Ø 3 mm in solid wood (no plugs needed there). Check: The screws and plugs suit most solid and hollow walls. If you are unsure, ask a specialist.
- Plugs in, cabinet back — Tap a wall plug 121714 into each hole with a hammer until it is flush with the wall. Then push the cabinet back to its place, against the skirting board.
- Screw it to the wall — From inside, put a washer 126916 on a long screw 147968 and screw it through the hole into the wall plug, on both sides. Without a skirting board (no knobs), use the shorter screws 158469. Check: The hollow side of the washer faces the screw head.
- Caps over the screws — Press a cap 190586 over each washer and screw head.
- Shelf supports — Push 8 shelf supports 10051650 into the holes in the side panels: 4 for each shelf, front and back, at the same height on both sides.
- Door stops on the shelves — Open bag 3. Lay both shelves flat. Press a door stop 10050715 into the hole in the middle of each shelf's front edge, then push a pin 10051084 down through it.
- Put in the shelves — Slide each shelf into the cabinet just above its 4 supports, door stop at the front, and lower it onto them. Start with the lower shelf.
- Hinge plates, left side — Hold a hinge plate 10039878 against the inside of the left side panel over the holes near the front, top and bottom, and tighten its 2 screws.
- Hinge plates, right side — Fit the 2 hinge plates on the right side panel the same way and tighten their screws.
- Hinges into the doors — Lay both doors face down on the rug. Press a hinge 10039873 into each of the 4 round holes, arm pointing away from the door edge.
- Tighten the hinge screws — Tighten the 2 screws of each hinge with a Phillips screwdriver.
- Knobs on the doors — Stand the doors up. Hold a knob 10052019 on the front of each door at the hole near its free edge and screw a bolt 119976 into it from behind.
- Hang the left door — Hold the left door in front of the cabinet and push the hinge arms back onto the hinge plates until they click. Open the door and tighten the screw on each hinge arm. Check: To line the doors up afterwards, turn the hinge screws as shown on manual page 33.
- Hang the right door — Hang the right door the same way: arms onto the plates until they click, then tighten the 2 screws.
- Done! — Your HAUGA cabinet is assembled and fixed to the wall. Max load per shelf: 18 kg. To line the doors up, turn the hinge screws as shown on manual page 33.
HAUGA cabinet with 2 doors: questions and answers
How long does it take to assemble the IKEA HAUGA cabinet with 2 doors?
About 2–3 hours for 2 people, working through the 41 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.
What tools do I need for the HAUGA cabinet with 2 doors?
Phillips screwdriver, pencil, drill with Ø 8 mm bit (Ø 3 mm for wood), hammer.
Can one person assemble the HAUGA cabinet with 2 doors?
It is planned as a 2-person build. One person can do most of it, but get help for steps 11, 16 and 18, where the furniture is lifted or turned.
Does the HAUGA cabinet with 2 doors need to be fixed to the wall?
The manual shows a wall fixing: see step 21 (Wall brackets) and step 25 (Mark the wall). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.
What size is the HAUGA cabinet with 2 doors once assembled?
70x46x116 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.
How many screws and fittings come with the HAUGA cabinet with 2 doors?
105 fittings of 25 kinds, the most numerous being 10 × pin, 10 × plug, 8 × back clip. The In the box table lists every one with its part number, so you can count them before you start.
Where can I download the IKEA HAUGA cabinet with 2 doors assembly instructions PDF?
The official PDF is manual AA-2204746-8, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 004.150.52 (white); other colours have their own numbers but usually the same manual.
Which IKEA manual is this guide based on?
The official manual AA-2204746-8. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.
What if a part or screw is missing?
Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example pin 151707). IKEA customer service can send replacement fittings using that number.
Related assembly guides
- IKEA HAUGA wardrobe with sliding doors assembly instructions
- IKEA HAUGA bedside table assembly instructions
- IKEA BILLY bookcase assembly instructions
- IKEA KALLAX shelf unit 2x4 assembly instructions
- IKEA BESTÅ frame assembly instructions
- IKEA HYLLIS shelving unit (in/outdoor) assembly instructions
- IKEA LACK wall shelf assembly instructions
- IKEA VESKEN shelf unit assembly instructions
All IKEA HAUGA assembly guides · All bookcases & shelves assembly guides · All furniture assembly guides
Stuck on a step? Common assembly problems and fixes · Furniture hardware explained