Step by StepAssembly Find your furniture

IKEA RAKKESTAD wardrobe with 3 doors assembly instructions

How to assemble the IKEA RAKKESTAD wardrobe with 3 doors (closet), step by step: 40 animated steps built from the official manual, about 2½–3½ h for 2 people, with Phillips screwdriver, hammer, pencil, drill, step ladder, Allen key (included).

IKEA RAKKESTAD wardrobe with 3 doors, assembled

A black-brown three-door wardrobe with a clothes rail and shelves: the frame is screwed together lying on its front, the back panels are nailed on, then it is raised, fixed to the wall and the panelled doors are hung. Size: 117×55×176 cm. About 2½–3½ h, 2 people. Tools: Phillips screwdriver, Hammer, Pencil, Drill, Step ladder, Allen key (included).

Based on the official IKEA manual AA-2213860-4 (PDF). Guide updated .

RAKKESTAD wardrobe with 3 doors: quick facts
Steps40
Time2½–3½ h
People2
ToolsPhillips screwdriver, Hammer, Pencil, Drill, Step ladder, Allen key (included)
Size117×55×176 cm
Official manualAA-2213860-4
IKEA article number704.537.62 (black brown)
Pieces in the box224

In the box

PartPart numberQuantity
Side panel2
Divider1
Top panel1
Bottom panel1
Shelf3
Plinth rail2
Back panel1
Folding back panel1
Door3
Clothes rail1468571
Screw10021916
Dowel10134538
Screw1095673
Screw10524838
Screw1090412
Door stop1098374
Knob1195953
Angle bracket1037171
Bumper pad sheet1070911
Nail guide1054941
Allen key1000011
Mounting plate1092219
Hinge1093389
Rail holder1573082
Glide1585688
Nail 405950 (2 bags)60
Wall bracket1069892
Screw1090492
Washer1008234
Screw1090482
Plug1217142

Steps

  1. Hinge mounting plates — Lay the left side panel, the divider and the right side panel flat on a soft surface, with the faces shown up. Screw 3 mounting plates (109221) near the front edge of each panel, 2 screws (105248) per plate: 9 plates and 18 screws. Check: Work on a rug or the cardboard so the black-brown foil isn’t scratched. Two people are needed for several steps.
  2. Dowels into the divider — Push 4 dowels (101345) into the holes in the two ends of the divider, 2 at each end.
  3. Dowels into the shelves — Lay out the 3 shelves and push 6 dowels into each one, 3 along each short edge: 18 dowels.
  4. Divider up, fixed shelf on — Stand the divider on its front edge, mounting plates facing away from you. Push one of the shelves onto the dowels in the middle of the divider: this is the fixed shelf.
  5. Screw the fixed shelf to the divider — From the other side of the divider, drive 2 screws (100219) through it into the edge of the fixed shelf with the Allen key (100001).
  6. Dowels into the top and bottom — Lay the bottom panel beyond the bottom end and the top panel beyond the top end. Push 4 dowels into each one, 2 at each end: 8 dowels.
  7. Door stops — Tap 2 door stops (109837) into the holes near the front edge of the bottom panel and 2 into the top panel, with a hammer.
  8. Turn the bottom over, angle bracket — Turn the bottom panel over. Screw the angle bracket (103717) to it with a short screw (109041), at the hole near the middle of the front edge. Check: Use the short screw 109041 here, not the longer 109567.
  9. Bottom panel onto the divider — Stand the bottom panel on its front edge against the end of the divider, lifting the divider slightly so its dowels go into the holes. Drive 2 screws (100219) through the bottom panel into the divider.
  10. Top panel onto the divider — Stand the top panel on its front edge against the other end of the divider, onto its dowels, and drive 2 screws (100219) through it into the divider.
  11. The other 2 shelves — Push the other 2 shelves onto the dowels of the divider, one above and one below the fixed shelf.
  12. Right side panel — Stand the right side panel on its front edge and push it onto the dowels of the top, bottom and shelves. Drive 2 screws (100219) into the bottom panel, but not fully: leave them a little loose for now.
  13. Screw the right side to the top and shelf — Drive 4 screws (100219) through the right side panel: 2 into the top panel and 2 into the fixed shelf.
  14. Tighten the bottom screws — Now tighten the 2 screws at the bottom panel fully, until the heads sit flush with the side panel.
  15. Dowels into the plinth rails — Lay out the 2 plinth rails and push 2 dowels (101345) into each end: 8 dowels.
  16. Glides on the plinth rails — Stand each rail on its edge and press 2 glides (158568) into the holes in its top edge.
  17. Front plinth rail — Lay the front plinth rail flat at the bottom end, glides outwards, and slide it under the bottom panel along the front edge until its dowels go into the right side panel.
  18. Middle plinth rail — Slide the second plinth rail in the same way, at the row of holes in the middle of the side panel, until its dowels go into the right side panel.
  19. Left side panel — Stand the left side panel on its front edge and push it onto the dowels of the top, bottom and plinth rails. Drive 4 screws (100219) through it: 2 into the top and 2 into the bottom panel. Check: Have a helper hold the frame steady while you fit the side panel.
  20. Bracket to the front rail — Fix the angle bracket under the bottom panel to the front plinth rail with the second short screw (109041). Check: Use 109041 here, not 109567.
  21. Lay on the back panels — Lay the single back panel over the right section, then unfold the folding back panel and lay it over the left section, so they sit in the rebates of the frame.
  22. First nail — Check the back panels are square in the rebates. Hold the nail guide (105494) on the edge at the top corner, put a nail (405950) through it and tap it in, then slide the guide away and drive the nail home.
  23. Nail the other corners — Keep the edges lined up and nail the other 3 corners, one nail each.
  24. Nail along the divider — Hammer 12 nails along the joint of the back panels, into the edge of the divider.
  25. Nail all round the edge — Nail the back panels all round the edge, using the nail guide to keep the nails in the edges of the frame: 44 nails.
  26. Glides under the side panels — Press 2 glides (158568) into the holes in the bottom end of each side panel: 4 glides.
  27. Raise the wardrobe — With a helper, lift the top end and walk the wardrobe up onto its glides, keeping the bottom end on the floor. Check: Two people needed. Check there is room under the ceiling to raise it.
  28. Against the wall, mark the top — Push the wardrobe against the wall where it will stand. Draw a pencil line on the wall along the top of the wardrobe. Check: The wardrobe must be fixed to the wall to stop it tipping over. Use a step ladder, not the wardrobe, to reach the top.
  29. Mark the wall brackets — Pull the wardrobe away from the wall. Hold each wall bracket (106989) with its flat leg on the pencil line and mark the wall through the slot in the upright leg.
  30. Drill and plug the wall — Drill a hole at each mark: 8 mm for the plugs in solid or hollow walls, then tap in the plugs (121714). In solid wood, drill 3 mm and use no plug. If unsure which fixings suit your wall, ask a specialist.
  31. Screw the brackets to the wall — Hold each bracket with its slot over the plug and screw it to the wall with a screw (109048) and a washer (100823).
  32. Push it back — Push the wardrobe back against the wall, so the flat legs of the brackets rest on the top panel.
  33. Screw the brackets to the top — Screw each bracket to the top panel with a short screw (109049) and a washer (100823), through the slot in the flat leg. Check: Use 109049 here: the longer 109048 is only for the wall.
  34. Clothes rail holders — Screw a rail holder (157308) to the left side panel and one to the divider, near the top, with a screw (105248) each.
  35. Clothes rail — Drop the clothes rail (146857) into the two holders.
  36. Hinges on the doors — Lay the 3 doors flat, inside face up. Press a hinge (109338) into each of the 9 round holes, arm towards the door edge, and fix each with 2 screws (105248): 18 screws.
  37. Hang the doors — Hook each hinge arm onto its mounting plate: the left door on the left side, the middle door on the divider, the right door on the right side. Open the doors and tighten the screw on each of the 9 hinge arms. Check: Have a helper hold each door while you clip its hinges on.
  38. Knobs — Hold a knob (119595) on the front of each door at the hole near the opening edge and screw it on from the inside with a screw (109567).
  39. Bumper pads — Close the left and middle doors. Stick the 2 bumper pads from the sheet (107091) on the front edge of the divider, near the top and the bottom, where the right door closes. Then close the right door.
  40. Done! — Your RAKKESTAD wardrobe is ready. If a door hangs crooked or the gaps are uneven, adjust it with the screws on its hinges (height, side and depth). Keep it fixed to the wall.

RAKKESTAD wardrobe with 3 doors: questions and answers

How long does it take to assemble the IKEA RAKKESTAD wardrobe with 3 doors?

About 2½–3½ h for 2 people, working through the 40 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the RAKKESTAD wardrobe with 3 doors?

Phillips screwdriver, hammer, pencil, drill, step ladder, Allen key (included). Already in the box: Allen key.

Can one person assemble the RAKKESTAD wardrobe with 3 doors?

It is planned as a 2-person build. One person can do most of it, but get help for steps 8 and 27, where the furniture is lifted or turned.

Does the RAKKESTAD wardrobe with 3 doors need to be fixed to the wall?

The manual shows a wall fixing: see step 29 (Mark the wall brackets) and step 40 (Done). Use screws and plugs that suit your wall (wood, brick, concrete or plasterboard), and ask at a hardware store if you are not sure. Tall furniture and drawer units that are not fixed to the wall can tip over.

What size is the RAKKESTAD wardrobe with 3 doors once assembled?

117×55×176 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the RAKKESTAD wardrobe with 3 doors?

148 fittings of 20 kinds, the most numerous being 38 × dowel, 38 × screw, 16 × screw. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA RAKKESTAD wardrobe with 3 doors assembly instructions PDF?

The official PDF is manual AA-2213860-4, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 704.537.62 (black brown); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2213860-4. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example clothes rail 146857). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA RAKKESTAD assembly guides · All wardrobes assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained