Step by StepAssembly Find your furniture

IKEA IDANÄS side table assembly instructions

How to assemble the IKEA IDANÄS side table, step by step: 16 animated steps built from the official manual, about 45–60 minutes for 1 person, with Phillips screwdriver, flat-blade screwdriver, Allen key (included).

IKEA IDANÄS side table, assembled

White side table with tapered legs, a middle shelf and a bottom shelf, built on its side from two ready-made side frames with cam locks, then finished upright. Size: 46×36 cm. About 45–60 minutes, 1 person. Tools: Phillips screwdriver, Flat-blade screwdriver, Allen key (included).

Based on the official IKEA manual AA-2350133-1 (PDF). Guide updated .

IDANÄS side table: quick facts
Steps16
Time45–60 minutes
People1
ToolsPhillips screwdriver, Flat-blade screwdriver, Allen key (included)
Size46×36 cm
Official manualAA-2350133-1
IKEA article number004.960.48 (white)
Pieces in the box56

In the box

PartPart numberQuantity
Side frame2
Narrow top rail2
Wide lower rail2
Bottom shelf1
Middle shelf1
Top1
Glide1123574
Cam screw1183318
Wooden dowel10134512
Cam lock1067204
Cam lock1192534
Shelf pin1041716
Shelf bracket100516604
Screw1002114
Allen key1000011

Steps

  1. Glides under the legs — Lay both side frames flat on a soft surface, inside face up. Press a glide into the hole at the bottom end of each of the 4 legs.
  2. 8 cam screws into the legs — Screw a cam screw into each of the 4 small holes on the inside face of each frame: 2 at the top end and 2 beside the lower rail. Use a Phillips screwdriver.
  3. Dowels into the narrow rails — Take the 2 narrow rails (the ones with the small hole in the middle, as the manual shows) and lay them with the large holes up. Push a wooden dowel into the hole in each end.
  4. Stand the narrow rails on the top end — Stand the narrow rails upright on the 2 cam screws at the top end of the lying frame, dowels down. Push in 2 cam locks 106720 and turn each clockwise with a flat screwdriver to lock. Check: Use cam locks 106720 here, not 119253.
  5. Dowels into the wide rails — Lay the 2 wide rails with the large holes up and push a wooden dowel into each end. Then turn the frame round so its top end is away from you.
  6. Stand the wide rails by the lower rail — Stand the wide rails on the 2 cam screws beside the frame's lower rail, large holes facing inwards. Push in 2 cam locks 119253 and turn each clockwise to lock. Check: Use cam locks 119253 here, not 106720.
  7. Second frame onto the rails — Turn the second frame over, inside face down, and lower it straight onto the 4 rails so its cam screws and the rail dowels go into the holes.
  8. Lock the second frame — Push 2 cam locks 119253 into the wide rails and 2 cam locks 106720 into the narrow rails at the second frame, then turn each clockwise with the flat screwdriver.
  9. Stand it up, 6 shelf pins — Stand the table upright on its legs. Press 6 shelf pins into the holes on the inside of the lower rails: 2 in the front rail, 2 in the back rail and 1 in each side rail, long end into the hole. Check: Long end into the hole, collar against the rail, short end sticking out.
  10. Bottom shelf onto the pins — Tilt the bottom shelf, pass it in between the front legs, then level it and lower it onto the 6 shelf pins inside the lower rails.
  11. 4 shelf brackets into the legs — Screw a shelf bracket into the hole on the inside face of each leg, about two-thirds of the way up, cup facing up. Turn them in by hand.
  12. Middle shelf onto the brackets — Slide the middle shelf in from the front between the legs, just above the brackets, then lower it so the slots in its ends sit down over the 4 brackets.
  13. Dowels into the top rails — Push 4 wooden dowels into the holes in the top edge of the front and back top rails, 2 in each.
  14. Lower the top on — Lower the table top straight down onto the frame so the 4 dowels go into the holes in its underside. The stepped edge faces down.
  15. Screw the top on from below — From underneath, drive 4 screws up through the holes near the ends of the two side top rails into the table top. Tighten them with the Allen key.
  16. Done! — Your IDANÄS side table is ready. Each shelf holds up to 5 kg and the whole table up to 20 kg.

IDANÄS side table: questions and answers

How long does it take to assemble the IKEA IDANÄS side table?

About 45–60 minutes for 1 person, working through the 16 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the IDANÄS side table?

Phillips screwdriver, flat-blade screwdriver, Allen key (included). Already in the box: Allen key.

Can one person assemble the IDANÄS side table?

Yes, it is a one-person build.

What size is the IDANÄS side table once assembled?

46×36 cm, as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the IDANÄS side table?

46 fittings of 8 kinds, the most numerous being 12 × wooden dowel, 8 × cam screw, 6 × shelf pin. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA IDANÄS side table assembly instructions PDF?

The official PDF is manual AA-2350133-1, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 004.960.48 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2350133-1. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example glide 112357). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA IDANÄS assembly guides · All tables assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained