Step by StepAssembly Find your furniture

IKEA IDANÄS bedside table assembly instructions

How to assemble the IKEA IDANÄS bedside table (nightstand), step by step: 33 animated steps built from the official manual, about 1.5–2 hours for 1 person, with Phillips screwdriver, flat-blade screwdriver.

IKEA IDANÄS bedside table, assembled

A white bedside table on a separate leg frame with an open shelf and a drawer: the cam-lock carcass is built lying down, the moulded top hooks on, it is finished upside down and the drawer runs on full-extension runners. Size: 47×40×68 cm. About 1.5–2 hours, 1 person. Tools: Phillips screwdriver, Flat-blade screwdriver.

Based on the official IKEA manual AA-2223931-5 (PDF). Guide updated .

IDANÄS bedside table: quick facts
Steps33
Time1.5–2 hours
People1
ToolsPhillips screwdriver, Flat-blade screwdriver
Size47×40×68 cm
Official manualAA-2223931-5
IKEA article number904.588.10 (white)
Pieces in the box88

In the box

PartPart numberQuantity
Side panel2
Rail2
Top1
Back panel1
Shelf1
Leg pair2
Leg frame rail2
Drawer front1
Drawer side2
Drawer bottom1
Drawer back1
Runner100448861
Runner100448351
Screw1003474
Cam screw1183318
Dowel10134512
Cam lock 119253/1181374
Cam lock1106308
Screw1050734
Pin1517052
Plug1517062
Glide100025474
Clip100930816
Cap100930826
Shelf pin1313724
Pin1457184
Knob100411201
Screw1199761

Steps

  1. Runners on the side panels — Lay both side panels flat on a rug, inner face up. Put runner 10044886 along the bottom edge of one panel and runner 10044835 on the other, as drawn. Fix each with 2 screws (100347). Check: Work on a soft surface so the panels are not scratched.
  2. Dowels in the rails — Push a wooden dowel (101345) into the hole in each end of the 2 rails: 4 dowels.
  3. Cam screws in the side panels — Screw 2 cam screws (118331) into the holes near the bottom edge of each side panel, at the front and back ends of the runner: 4 cam screws.
  4. Rails on the first side panel — Stand both rails upright on the side panel with runner 10044886, one at each end of the runner. Push their dowels into the holes so the rails sit over the cam screws. The large round holes face outwards, as drawn. Check: Check the holes on both rails before you press them down.
  5. Lock the rails to the first side — Push a cam lock (119253) into the round hole at the lower end of each rail and turn it clockwise with a flat-blade screwdriver to lock it: 2 cam locks.
  6. Second side panel — Tip the side panel with its rails up onto its back edge so the rails lie level. Lift the other side panel, runner facing in, and push it onto the free ends of the rails so the dowels and cam screws go into the holes.
  7. Lock the second side — Push a cam lock (119253) into the hole at the other end of each rail and turn it clockwise to lock the second side panel: 2 cam locks.
  8. Hook on the top — Slide the top onto the upper ends of the side panels so the pins in the panels go into the keyhole slots underneath it. Then press the top towards the back until it locks, flush with the rails. Check: The top must be pushed all the way home on both sides before you go on.
  9. Turn it over, slide in the back — Tip the table over onto its top so it stands upside down. Slide the back panel down the grooves at the back of the side panels, behind the rail, with the cable cut-out at the top end, until it rests on the top.
  10. Fix the back to the rail — Push 2 plugs (151706) through the holes in the back panel into the rail, then press a pin (151705) into each plug.
  11. Clips on the back — Press 6 clips (10093081) into the holes: 2 along each side edge of the back panel and 2 into the top just behind the back. Push a cap (10093082) into each clip.
  12. Rails into the first leg pair — Stand one leg pair on the floor. Push a frame rail into each of its legs from the side so the 2 pins at the rail end go into the keyhole slots, then press the rail down to lock it.
  13. Second leg pair — Fit the other leg pair onto the free ends of both rails the same way: pins into the keyhole slots, then press until the rails lock.
  14. Dowels for the leg frame — Push 2 wooden dowels (101345) into the holes in the bottom edge of each side panel: 4 dowels.
  15. Leg frame on — Turn the leg frame upside down and lower it onto the carcass so the dowels go into the holes in its side rails.
  16. Screw on the leg frame — Screw the leg frame to the side panels with 4 long screws (105073), 2 through each side rail.
  17. Glides, then stand it up — Press a glide (10002547) into the end of each leg. Then turn the bedside table over and stand it on its legs. Check: Turn it over carefully; do not let it fall onto the legs.
  18. Shelf pins — Push 4 shelf pins (131372) into the holes inside the side panels at shelf height, 2 on each side.
  19. Slide in the shelf — Slide the shelf into the cabinet from the front, just above the shelf pins.
  20. Lower the shelf onto the pins — Lower the shelf so it rests on all 4 shelf pins, and check that it lies level.
  21. Cam screws in the drawer front — Lay the drawer front face down on the rug. Screw 4 cam screws (118331) into the holes near its short ends, 2 at each end.
  22. Dowels in the drawer sides — Stand the 2 drawer sides on their back ends and push 2 wooden dowels (101345) into the holes in the top end of each: 4 dowels. Check: Push the dowels in by hand only as far as they go.
  23. Drawer sides on the front — Turn each drawer side over and lower it onto the drawer front so its dowels and the cam screws go into the holes. The grooves for the bottom face inwards.
  24. Lock the sides to the front — Push 4 cam locks (110630) into the holes on the outside of the drawer sides near the front, and turn each one clockwise to lock it.
  25. Slide in the drawer bottom — Slide the drawer bottom down the grooves of the drawer sides until it sits in the groove of the front.
  26. Drawer back — Lay the drawer back across the top ends of the sides, tilt it down into the notches and press it in so it is flush with the ends of the sides.
  27. Pins through the sides — Push 4 pins (145718) through the holes in the drawer sides into the ends of the back, 2 on each side.
  28. Lock the back — Push 4 cam locks (110630) into the holes in the back, next to the pins, and turn each one clockwise to lock the back to the sides.
  29. Knob — Stand the drawer up. Hold the knob (10041120) on the front and screw it on from inside with the screw (119976).
  30. Pull out the runners — Pull the moving part of both runners all the way out towards you.
  31. Drawer onto the runners — Hold the drawer level in front of its opening and lay it onto the pulled-out runners. Push it back so the hooks at the back ends of the runners catch in the holes of the drawer back.
  32. Click it down and push it in — Press the front of the drawer down so the locking devices under it click onto the runners, then push the drawer all the way in. Check: The drawer front can be adjusted up and down at the locking devices (manual page 24).
  33. Done! — Your IDANÄS bedside table is ready. If the drawer front is not level with the cabinet, lift it at the locking devices under the drawer, turn the adjuster and press it back down.

IDANÄS bedside table: questions and answers

How long does it take to assemble the IKEA IDANÄS bedside table?

About 1.5–2 hours for 1 person, working through the 33 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the IDANÄS bedside table?

Phillips screwdriver, flat-blade screwdriver.

Can one person assemble the IDANÄS bedside table?

Yes, it is a one-person build.

What size is the IDANÄS bedside table once assembled?

47×40×68 cm, as given for this model. Leave extra floor space around it while you build.

How many screws and fittings come with the IDANÄS bedside table?

72 fittings of 17 kinds, the most numerous being 12 × dowel, 8 × cam screw, 8 × cam lock. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA IDANÄS bedside table assembly instructions PDF?

The official PDF is manual AA-2223931-5, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 904.588.10 (white); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2223931-5. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example runner 10044886). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All IKEA IDANÄS assembly guides · All dressers & drawers assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained