Step by StepAssembly Find your furniture

IKEA NORDEN gateleg table assembly instructions

How to assemble the IKEA NORDEN gateleg table, step by step: 13 animated steps built from the official manual, about 1–2 hours for 2 people, with Phillips screwdriver, flat-blade screwdriver, hammer, Allen key (included).

IKEA NORDEN gateleg table, assembled

Solid birch drop-leaf table: a slim underframe with 6 small drawers and two swing-out gate legs, so it folds down to a 26 cm deep console. Size: 26/89/152x80 cm. About 1–2 hours, 2 people. Tools: Phillips screwdriver, Flat-blade screwdriver, Hammer, Allen key (included).

Based on the official IKEA manual AA-2580705-1 (PDF). Guide updated .

NORDEN gateleg table: quick facts
Steps13
Time1–2 hours
People2
ToolsPhillips screwdriver, Flat-blade screwdriver, Hammer, Allen key (included)
Size26/89/152x80 cm
Official manualAA-2580705-1
IKEA article number904.238.87 (birch)
Pieces in the box162

In the box

PartPart numberQuantity
Side frame with gate leg2
Bottom cross rail2
Table top middle section1
Drop leaf2
Stop block2
Drawer front6
Drawer back6
Drawer side12
Drawer bottom6
Hinge100056014
Allen key100833771
Wooden dowel1013528
Bolt1053304
Glide1072714
Screw11073342
Drawer fixing11654648
Screw1174944
Connecting plate1201392
Cross dowel1211214
Gate leg glide1565082

Steps

  1. Join the two side frames — Stand the two side frames up, gate legs facing out. Push 2 dowels 101352 into each end of both bottom cross rails, press the rails into the legs of one frame, then push the other frame onto them. Check: The gate legs come hinged to the frames. Here they swing freely, so take care when moving the frames.
  2. Connecting plates on top — Lay the 2 connecting plates 120139 across the top rails of both frames and fix each one with 2 screws 110733 through the round holes at its ends. Check: The countersunk side of the holes faces up. The slotted holes stay free for now.
  3. Stop blocks under the leaves — Lay the middle section and the two drop leaves upside down on a soft surface, edge to edge. Screw a stop block onto each leaf with 2 screws 117494, between the battens near its outer end.
  4. Hinge the leaves on — Lay a hinge 10005601 across each joint near both ends, 4 in all, and fix each one with 8 screws 110733: 4 into the middle section and 4 into the leaf.
  5. Bolt the cross rails — Fold the gate legs in against the frames and turn the frame upside down. Put the 4 cross dowels 121121 into the holes in the cross rails and turn them with a flat screwdriver so the threaded hole lines up. Then screw the 4 bolts 105330 through the legs into them with the Allen key 10083377.
  6. Frame onto the table top — Lower the upside-down frame onto the middle section of the top, between the hinges. Screw the plates to the top with 3 screws 110733 each: first the centre hole, then the two slots.
  7. Glides in the legs — Tap a glide 107271 into the end of each of the 4 corner legs with a hammer.
  8. Gate leg glides, then turn it over — Tap a glide 156508 into the end of each gate leg. Swing both leaves over against the sides of the frame, then turn the table over, end over end, onto its legs. Check: Get help to turn the table over.
  9. Drawer sides and back — Build the 6 drawers. For each one, stand the back between the two sides and knock 4 fixings 116546 through the sides into the back, 2 per side.
  10. Drawer bottom and front — Slide a bottom into the grooves of each drawer from the open end, put the front on and knock 4 fixings 116546 through the sides into it. Check: The finger notch in the front goes at the top.
  11. Drawers in — Slide 3 drawers into each end of the frame, fronts facing out: they run on the ledges of the rails.
  12. Unfold a leaf — To open the table, lift a leaf and swing its gate leg out under it until the pin on top of the leg sits in the hole of the stop block. To fold it, swing the gate leg back in first, then lower the leaf. Check: One leaf up: 89 cm long. Both leaves up: 152 cm. Folded: 26 cm.
  13. Done! — Your NORDEN gateleg table is ready, here with one leaf up. Lift the other leaf the same way for the full 152 cm, or fold both down to a 26 cm deep console.

NORDEN gateleg table: questions and answers

How long does it take to assemble the IKEA NORDEN gateleg table?

About 1–2 hours for 2 people, working through the 13 steps of this guide. Unpack and sort the hardware first: the In the box list has every part with its count, so you can check nothing is missing before you start.

What tools do I need for the NORDEN gateleg table?

Phillips screwdriver, flat-blade screwdriver, hammer, Allen key (included). Already in the box: Allen key.

Can one person assemble the NORDEN gateleg table?

It is planned as a 2-person build. One person can do most of it, but get help for steps 1, 8 and 12, where the furniture is lifted or turned.

What size is the NORDEN gateleg table once assembled?

26/89/152x80 cm, as given for this model. Leave extra floor space around it while you build, and room to lift or stand it up.

How many screws and fittings come with the NORDEN gateleg table?

122 fittings of 10 kinds, the most numerous being 48 × drawer fixing, 42 × screw, 8 × wooden dowel. The In the box table lists every one with its part number, so you can count them before you start.

Where can I download the IKEA NORDEN gateleg table assembly instructions PDF?

The official PDF is manual AA-2580705-1, free from ikea.com; this guide links it next to the steps. To find the product page with its documents, search ikea.com for article number 904.238.87 (birch); other colours have their own numbers but usually the same manual.

Which IKEA manual is this guide based on?

The official manual AA-2580705-1. Manuals and fittings change over time, so compare this code with the one printed on your paper manual. If they differ, follow your paper manual.

What if a part or screw is missing?

Check every box and all the packaging first: small fittings are often taped inside. Each fitting in the In the box list has its IKEA part number (for example hinge 10005601). IKEA customer service can send replacement fittings using that number.

Related assembly guides

All tables assembly guides · All furniture assembly guides

Stuck on a step? Common assembly problems and fixes · Furniture hardware explained